manual

Read pages 3-6
for kit assembly.
RIGHT SIDE
LADO DERECHO
LEFT SIDE
LADO IZQUIERDA
"B1" BRACKET USE HOLE #1
"B1" SOPORTE USA ABERTURA
NO. 1
"B2" BRACKET USE HOLE #1
"B2" SOPORTE USA ABERTURA NO. 1
"C2" BRACKET USE HOLE #1
"C2" SOPORTE USA ABERTURA NO. 1
"A1" BRACKET USE HOLE #1
"A1" SOPORTE
USA ABERTURA
NO. 1
FRONT OF KIT
FRENTE DE
ESTUCHE
Read pages 3-6
for kit assembly.
"A1" BRACKET USE HOLE #2
"A1" SOPORTE USA
ABERTURA NO. 2
RIGHT SIDE
LADO
DERECHO
LEFT SIDE
LADO
IZQUIERDA
"B1" BRACKET USE HOLE #2
"B1" SOPORTE USA ABERTURA NO. 2
FRONT OF KIT
FRENTE DE
ESTUCHE
14
1982-92 Chevrolet Camaro
1982-84 Pontiac Firebird
RADIO REMOVAL:
1. Remove the four screws from the radio trim panel.
2. Pull the panel up and outward towards the right.
3. Remove the four screws from the radio bracket, pull the radio out of the cavity. Disconnect the
antenna, speaker and all the electrical connections, then remove the radio.
NOTE: During the installation procedure the right side of the console must be pushed out 1/2 inch
to accommodate some units. Loosen the right side of, or remove the factory rear support bar.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1994-96 Chevrolet Caprice Classic
1994-96 Chevrolet Impala SS
RADIO REMOVAL:
1. Remove the fuse panel on the left side of the dash.
2. Extract one 9/32 inch screw behind the fuse panel.
3. Extract the two 9/32 inch screws from the under the dash panel on the driver's side (not the black
wiring access panel).
4. Extract the two 9/32 inch screws from below the ash tray.
5. Extract the two 9/32 inch screws from the top of the instrument panel bezel.
6. Make sure the parking brake is on, then insert the key and turn to the "on" position.
7. Put the vehicle into fi rst or low gear, and tilt the steering column adjustment all the way down and pull
outward on the instrument panel bezel. There are two spring clips on the bottom, release and remove
the spring clips.
8. Extract the four 9/32 inch screws holding the ash tray, remove the ash tray , unplug the connector
for the light.
9. Open the glove box.
10. Starting from the left side of the dash, working below the steering column, pull gently outward to
start releasing the spring clips.
11. Work all the way across the dash piece, there are about eight spring clips total. The last one will pop
out near the glove box. Remove the dash.
12. Extract the two 9/32 inch screws holding the radio, slide the radio out.
13. Unplug all the connectors and the antenna and remove the radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.