Installation instructions

9
1980-83 Chrysler Cordoba
1980-83 Dodge Mirada
Radio Removal:
1. Remove four screws securing the radio dash panel: two above the radio and two above the heater
controls.
2. Remove the radio dash panel. Remove two screws securing the radio to the dash. Pull the radio
out.
3. Disconnect power, antenna, and all speaker and electrical connections.
#2190 Panel
1975-79 Chrysler Cordoba
1975-79 Plymouth Fury
Radio Removal:
1. Remove four securing screws from the bottom edge of the radio dash panel.
2. Remove two securing screws from the top edge of the panel above the radio.
3. Unscrew the retainer ring securing the remote mirror control and remove the panel.
4. Remove two screws securing radio to the dash. Pull the radio out.
5. Disconnect power, antenna and all speaker and electrical connections.
#2190 Panel
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 5 & 6.
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
Para la instalación de radios DIN ISO y radios que se montan por los ejes, ver las páginas 5 y 6.
USE THESE SUPPORT TABS AS REQUIRED
Usar tantas de estas pestañas como sea
necesario
USE THIS BRACKET
Usar este braquete
REMOVE ALIGNMENT
PIN - BOTTOM
Sacar la clavija de
alineamiento - Inferior
USE THIS BRACKET
Usar este braquete
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 5 & 6.
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
Para la instalación de radios DIN ISO y radios que se montan por los ejes, ver las páginas 5 y 6.
USE THESE SUPPORT TABS AS REQUIRED
Usar tantas de estas pestañas como sea
necesario
REMOVE ALIGNMENT
PIN - BOTTOM
Sacar la clavija de
alineamiento - Inferior
Radio Removal:
1. Remove nine securing screws from the top and bottom of the radio trim panel. Remove the panel by
pulling it down and out.
2. Unhook the wiring harness.
3. Remove the two Chrysler anti-theft bolts retaining the radio (use Snap-On bit TTW 12 for 1/4" drive)
and remove the radio. Disconnect power, ground cable, antenna and speaker wires.
1983-84 Chrysler E Class
1984-88 Chrysler Le Baron
1984-87 Chrysler New Yorker
1983-88 Dodge 600 ES
1985-89 Dodge Aries 1981-89 Plymouth Reliant
USE THESE SUPPORT
TABS AS REQUIRED
Usar tantas de estas
pestañas como sea
necesario
USE THIS BRACKET
Usar este braquete
#2190 Panel
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 5 & 6.
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
Para la instalación de radios DIN ISO y radios que se montan por los ejes, ver las páginas 5 y 6.
REMOVE ALIGNMENT
PIN - BOTTOM
Sacar la clavija de
alineamiento - Inferior
Read pages 2-6
for kit assembly.
Read pages 2-6
for kit assembly.
Read pages 2-6
for kit assembly.