Installation instructions

29
Radio Removal:
1. Remove three screws from the radio trim below the dash.
2. Open out the 1-1/2" wide plastic trim piece above the radio trim.
3. Remove three screws from behind the trim. Remove the instrument cluster trim panel.
4. Remove three screws which secure the radio and the radio brackets to dash.
5. Disconnect the two wiring harnesses, antenna lead, and harness retaining clip. Remove the radio.
1984-89 Lincoln Town Car
Read pages 2-6
for kit assembly.
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 5 & 6.
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
Para la instalación de radios DIN ISO y radios que se montan por los ejes, ver las páginas 5 y 6.
Read pages 2-6
for kit assembly.
1986-89 Mercury Sable
Radio Removal:
1. Carefully pull on the edges of the radio trim panel
to release the plastic clips, and remove the trim
panel.
2. Remove four screws which secure the radio to
the dashboard, slide the radio out of the dash,
disconnect the harnesses and antenna, then
remove radio.
USE THIS BRACKET
Usar este braquete
USE THIS BRACKET
Usar este
braquete
#1550 Panel
1988-90 Mercury Tracer
USE BRACKETS SHOWN
Usar los braquetes que se muestran
USE THIN SPACER
Usar un espaciador delgado
USE THIN SPACER
Usar un espaciador delgado
Radio Removal:
1. Remove three screws from the underside of the upper lip of the radio/console trim panel.
2. Remove ashtray and remove two screws from inside the ashtray cavity.
3. Gently unsnap the trim panel, disconnect the wiring and remove the panel.
4. Remove four screws securing the radio pull the radio out of the cavity and disconnect the wiring,
and remove the radio.
#1550 Panel
CUT LOWER BRACKETS
ALONG CUT LINES
Cortar los braquetes inferiores a lo largo de las líneas de corte
Read pages 2-6
for kit assembly.
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
NOTE: INSTALLATION OF A DIN UNIT MAY REQUIRE DASH MODIFICATIONS.
NOTA: La instalación de una unidad DIN puede requerir modificar el tablero del vehículo.
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 5 & 6.
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
Para la instalación de radios DIN ISO y radios que se montan por los ejes, ver las páginas 5 y 6.
USE THIS BRACKET
Usar este braquete
USE THESE SUPPORT TABS AS REQUIRED
Usar tantas de estas pestañas como sea
necesario
REMOVE ALIGNMENT
PIN - BOTTOM
Sacar la clavija de
alineamiento - Inferior
#2190 Panel
1989-95 Plymouth Acclaim
Radio Removal:
1. Carefully release the spring clips securing the radio/dash trim: three clips along the top and two at
the bottom. Disconnect the panel light and remove the trim piece.
2. Extract the two bolts securing the radio: one at the top right, and one at the bottom left of the radio.
3. Pull the radio out of the dash cavity, disconnect the antenna and all electrical connections, and
remove the radio.
Read pages 2-6
for kit assembly.
USE THIS BRACKET
Usar este braquete
USE THESE SUPPORT TABS AS REQUIRED
Usar tantas de estas pestañas como sea
necesario
REMOVE ALIGNMENT
PIN - BOTTOM
Sacar la clavija de
alineamiento - Inferior
#2190 Panel