Installation instructions

22
1983-88 Ford Bronco II
1983-88 Ford Ranger
Radio Removal:
1. Remove the knobs from the radio.
2. Remove four screws from the top leading edge of the instrument cluster trim panel. Carefully pry the
top edge loose.
3. Carefully pry out the trim strip below the dash pocket, right and left of the ashtray strip.
4. Depress the spring clip behind light switch knob and remove knob. Carefully pry out the trim strip
from this location.
5. Remove the remaining four screws from the bottom edge of the instrument cluster trim panel
and remove the panel.
NOTE: If the truck is not equipped with a radio unscrew the dummy plate covering the radio
openings in the trim panel.
6. Remove four screws securing the radio assembly to the dash. Pull the radio out. Disconnect the
power, antenna, and all speaker and electrical connections.
Read pages 2-6
for kit assembly.
Read pages 2-6
for kit assembly.
1987-91 Ford Bronco Full Size
1987-91 Ford F-Series Pickup
Radio Removal:
1. Firmly pull on the edges of the radio trim panel to release the trim panel clips and remove the panel.
2. Remove four screws from the radio mounting bracket. Slide the radio out of the dash, disconnect
the wiring harnesses, and remove the radio.
3. Secure the radio/kit assembly to the dash using the four screws removed earlier.
4. Reassemble dash by reversing steps in the radio removal.
"A" RIGHT
Derecho
"R" "A"
#1550 Panel
"A" LEFT
Izquierdo
"L" "A"
"A" SPACER
Espaciador
"A"
"A" SPACER
Espaciador
"A"
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 5 & 6.
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
Para la instalación de radios DIN ISO y radios que se montan por los ejes, ver las páginas 5 y 6.
1975-91 Ford E150/E250/E350 Van
Radio Removal:
1. Remove the knobs and the shaft nuts from the radio.
2. Remove six screws from the dash panel.
3. Remove the panel and disconnect the cigarette lighter.
4. Remove four screws securing the radio mounting bracket to the dash. Release the rear support and
remove the assembly.
5. Disconnect the power, antenna, and all speaker and electrical connections.
Read pages 2-6
for kit assembly.
NOTE: INSTALLATION OF A DIN UNIT MAY REQUIRE DASH MODIFICATIONS.
NOTA: La instalación de una unidad DIN puede requerir modificar el tablero del vehículo.
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 5 & 6.
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
Para la instalación de radios DIN ISO y radios que se montan por los ejes, ver las páginas 5 y 6.
USE THIS BRACKET
Usar este braquete
USE THESE SUPPORT TABS AS REQUIRED
Usar tantas de estas pestañas como sea
necesario
REMOVE ALIGNMENT
PIN - BOTTOM
Sacar la clavija de
alineamiento - Inferior
#2190 Panel
USE THIS BRACKET
Usar este braquete
USE THESE SUPPORT TABS AS REQUIRED
Usar tantas de estas pestañas como sea
necesario
REMOVE ALIGNMENT
PIN - BOTTOM
Sacar la clavija de
alineamiento - Inferior
#2190 Panel