Installation instructions

21
2001 Dodge Stratus
Radio Removal:
1. Using panel removal tool, carefully pry out
the bezel, disconnect, and remove.
2. Extract four Philips head screws securing
radio, disconnect, and remove.
Read pages 2-6
for kit assembly.
USE THESE SUPPORT
TABS AS REQUIRED
Usar tantas de estas
pestañas como sea
necesario
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 5 & 6.
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
Para la instalación de radios DIN ISO y radios que se montan por los ejes, ver las páginas 5 y 6.
Radio Removal:
1. Remove the ashtray from the dash, extract the two screws securing the ashtray bracket to the dash
and remove the bracket.
2. Open up the cup holder and extract the two screws securing it to the dash.
3. Carefully pry out on the perimeter radio dash bezel using a panel removal tool to release the
fastening clips, disconnect all connectors and remove the bezel.
4. Extract the two screws securing the radio to the dash, pull the radio from the dash cavity, unplug all
connectors, disconnect the ground strap and remove the radio.
1978-02 Dodge Van
1978-83 Plymouth Van
Read pages 2-6
for kit assembly.
USE THIS BRACKET
Usar este braquete
USE THESE SUPPORT TABS AS REQUIRED
Usar tantas de estas pestañas como sea
necesario
REMOVE ALIGNMENT
PIN - BOTTOM
Sacar la clavija de
alineamiento - Inferior
#2190 Panel
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 5 & 6.
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
Para la instalación de radios DIN ISO y radios que se montan por los ejes, ver las páginas 5 y 6.
Read pages 2-6
for kit assembly.
1985-91 Ford Aerostar
Radio Removal:
1. Remove two screws from the bottom edge of the radio trim panel.
2. Pull down two snaps above the air-conditioning outlet vents and remove the radio trim panel.
3. Pull out the radio. Remove four screws from the radio mounting bracket; disconnect the wiring, and
remove the radio.
1980-86 Ford Bronco - Pickup
Radio Removal:
1. Remove knobs from radio when vehicle is equipped with a radio.
2. Remove two screws from the top of the radio panel. Pull the top out and up to release the tabs on
the bottom of the panel.
3. Remove four screws from the radio mounting bracket. Remove the assembly.
4. Disconnect the power, antenna, and all speaker and electrical connections.
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 5 & 6.
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
Para la instalación de radios DIN ISO y radios que se montan por los ejes, ver las páginas 5 y 6.
Read pages 2-6
for kit assembly.
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 5 & 6.
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
Para la instalación de radios DIN ISO y radios que se montan por los ejes, ver las páginas 5 y 6.
#2561 Panel
USE THIS BRACKET
Usar este braquete
USE THESE SUPPORT TABS AS REQUIRED
Usar tantas de estas pestañas como sea
necesario
REMOVE ALIGNMENT
PIN - BOTTOM
Sacar la clavija de
alineamiento - Inferior
#2190 Panel
USE THIS BRACKET
Usar este braquete
USE THESE SUPPORT TABS AS REQUIRED
Usar tantas de estas pestañas como sea
necesario
REMOVE ALIGNMENT
PIN - BOTTOM
Sacar la clavija de
alineamiento - Inferior
#2190 Panel