Installation instructions

20
1994-97 Dodge Ram
Radio Removal:
1. Remove two screws securing the dash panel inside the glove box.
2. Remove four screws from the bottom edge of the dash panel and one on the left side of the panel.
3. Carefully pull the panel from the dash and remove the panel.
4. Remove two screws securing the radio to the dash. Pull the radio out.
5. Disconnect power, antenna, and all speaker and electrical connections.
Read pages 2-6
for kit assembly.
USE THIS BRACKET
Usar este braquete
USE THESE SUPPORT TABS AS REQUIRED
Usar tantas de estas pestañas como sea
necesario
REMOVE ALIGNMENT
PIN - BOTTOM
Sacar la clavija de
alineamiento - Inferior
#2190 Panel
Radio Removal:
1. Remove the ashtray
2. Carefully pull outward on the edges of the trim panel to release the snaps, and remove the panel.
3. Remove one retaining screw from above the right upper corner of the radio.
4. Pull the dash trim towards the passenger side to gain access to the upper right radio bolt; remove
the top right bolt and the lower left bolt.
5. Pull out the radio. Disconnect the power, antenna, speaker leads, and all other electrical
connections. Remove the radio.
1987-94 Dodge Shadow
1987-94 Plymouth Sundance
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 5 & 6.
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
Para la instalación de radios DIN ISO y radios que se montan por los ejes, ver las páginas 5 y 6.
Read pages 2-6
for kit assembly.
USE THIS BRACKET
Usar este braquete
USE THESE SUPPORT TABS AS REQUIRED
Usar tantas de estas pestañas como sea
necesario
REMOVE ALIGNMENT
PIN - BOTTOM
Sacar la clavija de
alineamiento - Inferior
#2190 Panel
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 5 & 6.
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
Para la instalación de radios DIN ISO y radios que se montan por los ejes, ver las páginas 5 y 6.
Read pages 2-6
for kit assembly.
Radio Removal:
1. Carefully release the spring type fasteners from the radio/console trim panel - three from along the
top and two from the bottom of the panel.
2. Remove two screws from along the top of the side console trim pieces, and spread the side piece
out slightly for access to the radio bolt.
3. After spreading the side piece, extract the top right radio mounting bolt, then remove the bottom left
bolt.
4. Spread the side piece once again to provide clearance for pulling the radio out of the cavity; pull the
radio out, disconnect the connectors, and remove the radio.
1989-95 Dodge Spirit
USE THIS BRACKET
Usar este braquete
USE THESE SUPPORT TABS AS REQUIRED
Usar tantas de estas pestañas como sea
necesario
REMOVE ALIGNMENT
PIN - BOTTOM
Sacar la clavija de
alineamiento - Inferior
#2190 Panel
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 5 & 6.
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
Para la instalación de radios DIN ISO y radios que se montan por los ejes, ver las páginas 5 y 6.