Installation instructions

14
1995-00 Chrysler Sebring
1995-00 Dodge Avenger
Radio Removal:
1. Carefully pry out on radio/AC control trim bezel to
release the snap clips. Remove the bezel.
2. Extract the two screws holding radio in, unplug
connector, unbolt ground wire from rear of radio
and remove radio.
USE THIS BRACKET (BOTTOM)
Usar este braquete (Inferior)
USE THIS
BRACKET(TOP)
Usar este braquete
(Superior)
#2190 Panel
Radio Removal:
NOTE: The factory radio provision is a DIN and a half opening.
1. Use panel removal tool to pry out radio dash bezel.
2. Disconnect and remove bezel.
3. Extract four Philips head screws from radio.
4. Pull radio away, disconnect and remove.
2001-05 Chrysler Sebring Convertible
2000-06 Chrysler Sebring, 4-Dr. Sedan
2002-06 Dodge Stratus Sedan
USE THESE SUPPORT
TABS AS REQUIRED
Usar tantas de estas
pestañas como sea
necesario
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 5 & 6.
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
Para la instalación de radios DIN ISO y radios que se montan por los ejes, ver las páginas 5 y 6.
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 5 & 6.
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
Para la instalación de radios DIN ISO y radios que se montan por los ejes, ver las páginas 5 y 6.
2001-05 Chrysler Sebring, Coupe
2002-06 Dodge Stratus Coupe
Radio Removal:
1. Extract two Philips head screws from bottom of radio bezel.
2. Using a panel removal tool, unsnap and remove the dashbezel.
3. Extract four Philips head screws securing radio;
lift away, disconnect, and remove.
USE THESE SUPPORT
TABS AS REQUIRED
Usar tantas de estas
pestañas como sea
necesario
#2561 Panel
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 5 & 6.
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
Para la instalación de radios DIN ISO y radios que se montan por los ejes, ver las páginas 5 y 6.
#2561 Panel
2001-06 Chrysler Town & Country
2001-06 Dodge Caravan
Radio Removal:
1. Open drink holder and remove screw cover panel at bottom of radio bezel, extract (2) Philips head
screws from behind.
2. Using a panel removal tool, unsnap, disconnect,
and remove the dash bezel.
3. Extract four Philips head screws securing radio,
lift away, disconnect, and remove.
USE THESE SUPPORT
TABS AS REQUIRED
Usar tantas de estas
pestañas como sea
necesario
#2561 Panel
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 5 & 6.
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
Para la instalación de radios DIN ISO y radios que se montan por los ejes, ver las páginas 5 y 6.
Read pages 2-6
for kit assembly.
Read pages 2-6
for kit assembly.
Read pages 2-6
for kit assembly.
Read pages 2-6
for kit assembly.