Owner's Manual

ManualsBrandsScosche ManualsAudio accessories & installationScosche CRQ04

your

product

onllne

www.scosche.com/register

CRQ04

2014-18

Dodge

Durango

ter

Consol

Dire

Fit

zel

PARTS

INCLUDED

1 .

(1)

Direct Fit Bezel

MQUSM

(1)

Vehicle Specific T-harness

(2)

MAGICPLATE"•

(2)

MAGICPLATE"' Applicator

(6)

Double-sided Adhesive

READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING

THIS

MOUNT

KIT.

WARNING:

Do not use the magnetic mount with any hard-drive based devices such

as:

iPod classic, iPod Video and Zune MP3 players. Use caution whenever removing

or handling plastic parts of any vehicle. Unnecessary force

pressure can cause pieces

to crack

break. Please use a plastic card

remove the metal plates. Remove adhesive

residue with a non-abrasive cleaner.

CAUTION: This magnetic device is not a toy. The small magnets are harmful

swallowed.

Keep away from children.

PRELIMINARY INTRODUCTION

Wirelessly charge your Qi-enabled smartphone without the need

plug your device into

a car charger or USS cable. Quickly charge your device at 5W

charging. The

high

powe

red neodymium magnets are 1

00%

safe and will

not

damage your device. The

CRQ04 works with Qi-enabled smartphones from these manufacturers: Apple, Samsung,

Google, Microsoft, LG, HTC, Motorola. Also works with Qi-enabled cases, receivers, and

battery covers.

CAUTION:

Disconnect

your

vehicles

negative

battery terminal

before

the

installation

help

prevent electncal

damaqe

recommend

the

use

of a

volU

ohm

meter

over

a test light

check

wiring.

test

gro1111(led

wire pro lie

can

cause

damage

the

vehicle's

computer

and/or

diagnostic

system.

Avoid all

factory

airbag

wirmy

airbags

can

accidentally

deploy

causing

serious

if1jury

death.

NOTE

See

your

vehicle's

instructions

for

any

special

tools

your

installation

might

require.

IMPORTANT!

NOT

RETURN

PRODUCT

THE

RETAILER.

you

need

assistance

replacement

parts

contact

at:

1-800-363-4490

www.scosche.com/contact.

Our

office

hours

are:

Mon-ffi:

8AM-5:30PM

(PST)

and

Sat:

8AM-2PM

(PST)

LIABILITY DISCLAIMER

This instruction booklet is based on carefully documented data and research

automobile disassembly, wire harness

and information pertaining

the installation

this kit. Scosche Industries, Inc. cannot be held responsible for

discrepancies/ inconsistencies that

ma~

occur due

the automobile manufacturing changes

options, or damages

that may occur in the automobile during the installation of components while using this booklet.

Summary of content (7 pages)

PAGE 1
Register your product onllne at www.scosche.com/register CRQ04 2014-18 Dodge Durango Qi Center Console Direct Fit Bezel PARTS INCLUDED 1. 2. 3. 4. 5. (1) Direct Fit Bezel w/ MQUSM (1) Vehicle Specific T-harness (2) MAGICPLATE"• (2) MAGICPLATE"' Applicator (6) Double-sided Adhesive READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS MOUNT KIT. WARNING: Do not use the magnetic mount with any hard-drive based devices such as: iPod classic, iPod Video and Zune MP3 players.
PAGE 2
MAGICPLATE™ MOUNTING OPTION 1 NOTE: For mounting directly to device, use the large single plate with template guide as shown in the instructions below. 0 8 Remove the white paper backing from both plates Line up the corresponding arrows on the Template Guide to the to the bottom of your phone. REMOVING THE PLATE Use a thin plastic card to carefully lift the plate's adhesive surface from the mounting surface. Slowly lift up and remove the plate.
PAGE 3
MAGICPLATE™ MOUNTING OPTION 3 (Continued) NOTE: For mounting directly• to Galaxy S9/S9+, use the (2) small plates with the integrated template guide for Galaxy as shown. •For mounting directly to device only. Do not mount to case. 0 A V Removethe white paper backing from both plates A W Line up "U" channel to the fingerprint reader and camera on the phone. Remove the backing from the protective film as shown on the removal tabs (A), and place between the device and the lower plate (B).
PAGE 4
Modification Required: Please read complete instructions before proceeding. Location modification required for this installation, proceed with caution. If you are unsure or feel that the installation is to difficult, we recommend you seek professional installation. Note that additional installation fees may apply and vary by location. Scosche is not responsible or liable for any additional fees or modification done by the installer.
PAGE 5
TESTING QI MODULE (MQUSM) Testing Connection Before proceeding to the preparation/installation please test the modules functionality by connecting the provided vehicle specific t-harness (diagram on right). Once the module is connected, place the Qi-enabled device on the module and refer to the LED Status chart below for specifics. For technical assistance with the installation please call or visit us on the web at: 1-800-383-4490 x1 I www.acosche.
PAGE 6
VEHICLE ASSEMBLY @--------.--. 9. Connect the provided power t-harness according to the diagram displayed under the Test Connection on page 5, or see illustration on the right. Connect the female and male 12V power connectors first then route the type-c connector to the designated slot created during the preparation steps on page 5. 10. Preform the following as listed, see illustration 10 at right for referance: A. Route the Type-C connector through the hole created durring preparation on the OEM panel.
PAGE 7
FCC STATEMENT This equipment has been tested and found to comply with the limits for a WPC device, pursuant to Part 18 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the product.