manual

REMOVE
ALIGNMENT
PIN - BOTTOM
USE THIS
BRACKET
SHAFT MOUNT (DIN-C) RADIOS
Using the radio's knobs/hardware, secure the radio to the mounting panel and to the shaft radio faceplate as
shown.
ASSEMBLING THE KIT (Cont'd)
REAR
SUPPORT
STRAP
CAUTION:
REAR SUPPORTING THE RADIO ADDS TO
THE INSTALLATION'S STRUCTURAL
INTEGRITY.
REAR
SUPPORT
STRAP
DIN RADIO
5MM SCREWS
CJ1278
MOUNTING
PANEL
CJ1278
ISO
MOUNTING
BRACKETS
CJ1278
TRIM RING
SNAP SHAFT TABS
SHAFT RADIO
SPACER (OPTIONAL)
SUPPLIED WITH
YOUR NEW RADIO
CJ1278
MOUNTING
PANEL
CAUTION:
REAR SUPPORTING THE RADIO ADDS TO
THE INSTALLATION'S STRUCTURAL
INTEGRITY.
DIN-ISO MOUNT: (DIN-E Radio with Side Mounting Holes)
1. Snap the DIN iso side mounting brackets to the back of the mounting panel (1 left and
1 right). Use supplied hardware to bolt them to the back of the kit panel.
2. Snap the DIN-ISO Trim Ring into the radio opening.
3. Load the Radio from the REAR of the mounting panel until the nosepiece of
the radio comes through the front of the kit.
4. Use the 5MM screws to secure the radio from the sides.
314
1998-01 Dodge Ram
Radio Radio:
1. Extract (1) Screw from lighter socket area.
2. Carefully pryout on the radio dash bezel to release the fastening
clips, disconnect all connectors and remove the bezel.
3. Extract the (2) screws securing the radio to the dash,
pull the radio from the dash cavity, unplug all
connectors, diconnect the ground strap and remove the radio.
1995-99 Dodge Neon
1995-99 Plymouth Neon
Radio Removal:
1. Remove the ashtray from the dash.
2. Carefully pry outward on the radio trim bezel to release spring
clips then remove.
3. Extract the two 3/8" screws securing the radio to the dash, pull
the radio from the dash cavity, unplug all connectors,
disconnect the ground strap and remove the radio.
Read pages 2-4 for kit assembly.
Read pages 2-4 for kit assembly.
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
REMOVE
ALIGNMENT
PIN - BOTTOM
USE THESE
SUPPORT
TABS AS
REQUIRED
USE THESE
SUPPORT TABS
AS REQUIRED
USE THIS
BRACKET
REMOVE
ALIGNMENT
PIN - BOTTOM
USE THESE
SUPPORT
TABS AS
REQUIRED
USE THESE
SUPPORT TABS
AS REQUIRED
USE THIS
BRACKET
Read pages 2-4 for kit assembly.
1994-97 Dodge Ram Pickup
Radio Removal:
1. Remove the ashtray from the dash, extract the two screws securing the ashtray bracket to the
dash and remove the bracket.
2. Open up the cup holder and extract the two screws securing it to the dash.
3. Carefully pry out on the perimeter radio dash bezel using a panel removal tool to release the
fastening clips, disconnect all connectors and remove the bezel.
4. Extract the two screws securing the radio to the dash, pull the radio from the dash cavity, unplug
all connectors, disconnect the ground strap and remove the radio.
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.