manual

Use the shaded mounting tabs and indicated brackets. Carefully
break or cut off the unused brackets. Then assemble the radio
and the mounting panel as shown below, and secure the kit to
your dash using the supplied screws. Reassemble your dash,
and attach the radio's front panel and controls.
The following example shows a typical installation.
CAUTION:
Disconnect your vehicle's negative battery terminal before the installation to help prevent electrical
damage. We recommend the use of a volt/ohm meter over a test light to check wiring. A test light or
grounded wire probe can cause damage to the vehicle's computer and/or diagnostic systems. Avoid all
factory airbag wiring. Airbags can accidentally deploy causing serious injury or death.
NOTES:
• See your vehicle's instructions for any special tools your installation might require.
• Read all instructions accompanying your car stereo/cassette player for proper wiring
and mounting instructions.
INTRODUCTION
ASSEMBLING THE KIT
Your kit includes:
The instructions for each vehicle show which mounting panel
and brackets to use.
• 1 Mounting Panel
• 2 Snap Shaft Brackets
• 1 ISO Trim Ring
• 2 Spacers
• 2 ISO Mount Brackets
• 1 Snap-In Pocket
The Scosche in-Dash Installation Kit for 1974-UP Chrysler and Jeep Vehicles provides the parts you need to
mount your car stereo/cassette player into your vehicle's dash. Refer to the individual instructions in this
manual to remove your vehicle's factory installed radio.
PRELIMINARY PARTS LIST
ASSEMBLING THE POCKET
1. Locate and align bottom guides and top snaps of
the pocket to kit panel.
2. Slide pocket on bottom guides while the top
snaps are aligned.
3. When aligned properly, the top pocket snaps will
lock to kit panel.
WIRE CODES
NOTE:For Factory WIring Codes go to: www.scosche-cars.com
2
Read pages 2-4 for kit assembly.
1978-02 Dodge Ram Van
1978-83 Plymouth Van
Radio Removal:
1. Remove two screws securing the dash panel inside the glove box.
2. Remove four screws from the bottom edge of the dash panel and
one on the left side of the panel.
3. Carefully pull the panel from the dash and remove the panel.
4. Remove two screws securing the radio
to the dash. Pull the radio out.
5. Disconnect power, antenna, and all
speaker and electrical connections.
REMOVE
ALIGNMENT
PIN - BOTTOM
USE THESE
SUPPORT
TABS AS
REQUIRED
USE THESE
SUPPORT TABS
AS REQUIRED
USE THIS
BRACKET
Read pages 2-4 for kit assembly.
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
1987-94 Dodge Shadow
1987-94 Plymouth Sundance
REMOVE
ALIGNMENT
PIN - BOTTOM
USE THESE
SUPPORT
TABS AS
REQUIRED
USE THESE
SUPPORT TABS
AS REQUIRED
USE THIS
BRACKET
Radio Removal:
1. Remove the ashtray
2. Carefully pull outward on the edges of the trim panel to release
the snaps, and remove the panel.
3. Remove one retaining screw from above the right upper corner of
the radio.
4. Pull the dash trim towards the passenger side to gain access to
the upper right radio bolt; remove the top
right bolt and the lower left bolt.
5. Pull out the radio. Disconnect the power,
antenna, speaker leads, and all other
electrical connections. Remove the radio.
Read pages 2-4 for kit assembly.
1989-95 Dodge Spirit
Radio Removal:
1. Carefully release the spring type fasteners from the radio/console trim
panel - three from along the top and two from the bottom of the panel.
2. Remove two screws from along the top of the side console trim pieces,
and spread the side piece out slightly for access to the radio bolt.
3. After spreading the side piece, extract the top
right radio mounting bolt, then remove the
bottom left bolt.
4. Spread the side piece once again to provide
clearance for pulling the radio out of the
cavity; pull the radio out, disconnect the
connectors, and remove the radio.
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
15
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
REMOVE
ALIGNMENT
PIN - BOTTOM
USE THESE
SUPPORT
TABS AS
REQUIRED
USE THESE
SUPPORT TABS
AS REQUIRED
USE THIS
BRACKET
15