User manual

ManualsBrandsScosche ManualsMobile PhonesBFTA

BFTAK

HANDS-FREE BLUETOOTH

INTERFACE FOR SELECT

2005-UP SELECT TOYOTA, SCION, LEXUS VEHICLES

iPhone is a trademark of Apple Inc., registered in the US and other countries.

SI 02/10-BFTAK (3000493)

SAT-READY RADIO IS REQUIRED FOR

ALL APPLICATIONS LISTED BELOW

APPLICATIONS HARNESS APPLICATIONS

Scosche’s BFTAK Bluetooth Interface will allow you to wirelessly communicate with your

Bluetooth enabled celular phone and Stereo Bluetooth transmitters. The BFTAK communi-

cates directly with your factory radio allowing you direct control of hands-free, voice dialing,

and A2DP functionality. These interfaces maintain the original integrity of important diagnostic

and safety systems within the vehicle. For up-to-date applications or any Technical asistance

with this product, call Scosche Tech support at (800) 621-3695 Ext 3.

LEXUS

GS 2006-07

IS250/350 2006-08

RX350 2005-08

SCION

tC 2005-06

xA 2005-06

xB 2005-06

xB 2008-09

xD 2008-09

TOYOTA

4RUNNER 2005-09

AVALON 2005-09

CAMRY 2007-09

COROLLA 2005-09

FJ CRUISER (PREMUIM/JBL RADIOS ONLY) 2007-09

HIGHLANDER 2005-09

LAND CRUISER 2005-07

MATRIX (NON-JBL RADIOS ONLY) 2009

MATRIX 2005-08

PRIUS W/NAVIGATION ONLY 2005-08

RAV4 2006-09

SEQUOUIA 2006-09

SIENNA 2005-09

SOLARA 2005-09

TACOMA (NON-JBL RADIOS ONLY) 2009

Summary of content (12 pages)

PAGE 1
BFTAK HANDS-FREE BLUETOOTH® INTERFACE FOR SELECT 2005-UP SELECT TOYOTA, SCION, LEXUS VEHICLES Scosche’s BFTAK Bluetooth Interface will allow you to wirelessly communicate with your Bluetooth enabled celular phone and Stereo Bluetooth transmitters. The BFTAK communicates directly with your factory radio allowing you direct control of hands-free, voice dialing, and A2DP functionality. These interfaces maintain the original integrity of important diagnostic and safety systems within the vehicle.
PAGE 2
IMPORTANT CELL PHONE DISCLAIMER: READ FIRST! • Some cellular phone manufacturers utilize a Bluetooth microprocessor that unfortunately is not compatible with the BlueFusion system. Some phones from Palm, LG (Envy/Envy2), Samsung (Impression) and HTC (Omni) have SAT1 MainMenu exhibited operating difficulties with the BlueFusion system.
PAGE 3
MICROPHONE INSTALLATION TECH TIP: Aim the microphone in the direction of the driver’s headrest. MICROPHONE INSTALLATION: 1. Attach the microphone to the headliner above the rear view mirror. 2. Carefully route the microphone cable behind the headliner and down the “A” (front most) pillar. Use caution when routing cable and avoid sharp edges or moving metal parts. 3. Route the cable to the BlueFusion interface location and plug it into the 3-pin connector on the Scosche “T “harness.
PAGE 4
ADDITIONAL PARING NOTES: • If pairing is unsuccessful, repeat steps 1-6 above. If you are unable to pair, please call Tech Support (800) 621-3695 Ext. 3 • After your phone has been initially paired with BlueFusion, it should easily re-connect for future use. Many phones will automatically re-connect to the BlueFusion system as long as you keep your phones Bluetooth feature active.
PAGE 5
USING THE RADIO CONTROLS/ NAV SCREEN NOTE: The radio controls and illustrations in this manual may vary between vehicle models, years and trim levels. This section is provided as a guide; your vehicle may differ.
PAGE 6
USING THE RADIO CONTROLS ACTIVE CALL MENU OPTIONS: (Displayed when phone call is connected): TOUCHSCREEN BUTTON 1 CH 001 Vol+ TOUCHSCREEN BUTTON 4 CH 004 Vol- TOUCHSCREEN BUTTON 2 PRESET BUTTONS #1 & #4 ADJUST PHONE CALL VOLUME CH 002 Toggle PRESET #2 TOGGLES (Switch) BETWEEN TWO ACTIVE CALLS TOUCHSCREEN BUTTON 3 CH 003 EndCall TOUCHSCREEN BUTTON CH 005 5 Transfer-to-Headset PRESET #3 ENDS ACTIVE CALL PRESET #5 TRANSFERS CALL TO HANDSET (Privacy mode) TOUCHSCREEN BUTTON 6 CH 100 2Ra
PAGE 7
SWITCHING BETWEEN SOURCES Your BlueFusion system appears as an XM source to the Factory radio. This is why it is required to go to the XM Radio band first to your BlueFusion screen While using other sources other than XM (BlueFusion) the interface will automatically switch to the XM source when you have an incoming phone call. The radio switches through the sources to find the XM source on the radio, some audio may bleed through while switching sources.
PAGE 8
HANDS-FREE OPERATION HANDS-FREE OPERATION INCOMING CALLS: When receiving an incoming call the Factory radio will automatically switch to the BlueFusion source and display caller number. The BlueFusion system is designed to display caller ID only. (Some phones may provide additional message string information and provide a name in place of the calling number. Your results may vary). BlueFusion does not support Phonebook profile. TO ANSWER A CALL: Press Seek Forward once on the steering wheel controls.
PAGE 9
SECONDARY AND CONFERENCE CALL HANDLING When receiving a second call while in an active call the BlueFusion display a new menu with a list of second call handling functions. TO ANSWER THE SECOND CALL AND PLACE ACTIVE CALL ON HOLD: Press Seek forward once on radio. SWAP CALLS: (option only present with 2 active phone calls) From radio scroll to “swap calls” in the menu and press seek forward once. RELEASE HELD CALL: On the radio scroll to “Release held call” in the menu and press seek forward once.
PAGE 10
A2DP/AVRCP STREAMING AUDIO A2DP STREAMING AUDIO/ AVRCP REMOTE CONTROLS: Important Cell Phone Disclaimer: READ FIRST! BlueFusion will support audio streaming until it is in paired with a cell phone (whether this is within the same device supporting multiple profiles or two separate device. -While streaming A2DP, redial and voice dial functions are DISABLED.
PAGE 11
TROUBLE SHOOTING For all issues take the following steps first before moving on to any other trouble shooting. This process insures complete initialization. 1) Turn off vehicle. 2) unplug interface. 3) Enter vehicle and close all doors. 4) Wait until the vehicle computer enters “Sleep” Hibernation. (After approx. 3 min. Listen for click sound in thee doors). 5)Without opening doors, plug in interface. 6) Start engine. Unit has been installed properly but BlueFusion screen does not display.
PAGE 12
FCC This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: 1) This device may not cause interference, and 2) this device must accept any interference that may be received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. Such modification could void the user’s authority to operate the equipment.