User's Manual

2
3
GETTING STARTED
ASSEMBLING THE CIGARETTE LIGHTER DOCK STATION:
1. Align the notches on the top of the lighter probe with
the notches in the bottom of docking station and slide
forward to lock into place as shown.
ASSEMBLING THE EAR HOOK:
1. Test fit the 2 ear hooks over your
left or right ear and choose the
one that fits comfortably.
2. Rotate the ear hook 90 degrees
and simply snap onto the
headset as shown.
3. Point headset (MIC) in the
direction of your mouth for best
operation. (Microphone is
located in the tip.)
GETTING STARTED (Cont'd)
CHARGING THE BATTERY:
Before using the headset for the first time, you should charge the
battery for a full 2 hours. Charge the headset either in the
docking station or using the USB/PC charging cable provided in
the kit.
PC-USB CHARGING:
Plug the USB charging cable into your computer and plug the
other end into the earpiece as shown. The LED indicator will
illuminate in RED while the battery is charging.
DOCK STATION CHARGING:
Place the headset into the docking station
when vehicle cigarette lighter socket has
power as shown. The LED indicator will
illuminate in RED while the battery is
charging.
The headset must be paired with a Bluetooth
®
enabled mobile phone before use. Keep the CBH and phone
in the range of 3 feet (1 meter) when pairing.
1. Power on the CBH Headset.
2. Press and hold the volume (+) key for 5 seconds. The BLUE indicator light will blink and (2) beeps will
be heard indicating the headset is in paring mode.
3. While headset LED is flashing, follow the instructions for your cell phone to seek (or discover) any
nearby Bluetooth
®
devices. If needed, consult your cell phone’s manual for information on pairing or
discovering Bluetooth
®
devices for your particular phone.
4. After searching, your phone should display a list of local Bluetooth
®
devices. The phone should display
the Scosche CBH device as: BH5300
5. Select BH5300 and confirm the connection. Enter the password "1234". Bluetooth
®
pairing should now
be complete.
6. If your phone fails to locate the Scosche CBH headset, then check to make sure your phone is seeking
Bluetooth
®
devices. Check to make sure the Scosche CBH is in pairing mode. Repeat steps 1-5. If you
cannot successfully pair the two devices, call Tech Support at [phone] Ext 3.
PAIRING THE HEADSET WITH BLUETOOTH DEVICES
OPERATION / HEADSET
POWER ON:
Press and hold the Power Key for 5 seconds. The indicator light will blink once Red, then Blue. You will hear
the 3 chimes
POWER OFF:
Press and hold the Power Key for 5 seconds. You will hear one beep at approximately 3 seconds and
CONTINUE to hold the key for 2 additional seconds, and then the headset will beep 3 times indicating power
is off. The headset will disconnect with any paired device when powered off.
CALL ANSWER:
When the headset is ringing, simply press and release the Power Button to ANSWER an incoming call.
CALL ENDING:
During conversation, simply press and release the Power Button to END the call.
CALL REJECT:
To reject (non-answer) an incoming call, press the Power Button for 3 seconds while the headset is ringing to
REJECT the call.
VOLUME:
During conversation, press "+" to increase volume or press "-" to decrease volume.
VOICE DIAL:
Press and hold the Power Key for 3 seconds. You will hear one beep, then state the voice name of the
contact you’re calling.
NOTE: Your Bluetooth
®
phone must support voice dialing capability to use this feature. Consult your
phone’s user guide for information specific to your phone.
LAST NUMBER REDIAL:
Press and release the Power Key. Redialing of the last number called should begin automatically.
HANDS-FREE TAKE-OVER:
During a conversation you can switch to the CBH hands-free headset by simply pressing the power button if
the CBH headset is already powered on. If the headset is off, then power it on and the headset should take
over after it connects to your mobile phone.
MICROPHONE MUTE:
During conversation, press "+" volume for 5 seconds. A beep will be heard indicating the MIC has been
muted.
CALL SWAP:
During conversation, press the Power Button 2X to answer the second incoming call.
NOTE: Your Bluetooth
®
phone must support hands-free call swapping capability to use this feature. Consult
your phone’s user guide for information specific to your phone.
3-WAY CALL:
During conversation, press the Power and Volume (+) Button until a beep is heard.
NOTE: Your Bluetooth
®
phone must support hands-free 3-way call capability to use this feature. Consult
your phone’s user guide for information specific to your phone.