User Manual

ManualsBrandsSCOORNEST ManualsSecurity CameraSCOORNEST A9 Wireless Security Camera

Table Of Contents

Wireless Security Camera User Guide

Wireless Security Camera User Guide

If you have any problems, please contact us without hesitation!

We will reply your messages within 24 hours to help you solve the problem.

Forward

1. After turn on the camera，please reset it first .

Reset: Press and hold the Mode button of the camera for about 5 seconds, during

which the red indicator light will flash rapidly, release the button, wait for the

indicator light to flash steadily and the reset is successful.

2. There are no speakers in this camera, so no sound will come out of the camera

when in use.

3. When using an SD card with a size of 64GB and above, please format the card

before it can be recognized and recorded (you can download Disk Genius on your

computer and select FAT32 to format your SD card)

4. Please turn off the camera before inserting the SD card. Removing the SD card

while the camera is on may cause file corruption.

5. Charge the camera for about 3 hours for the first time. The battery naturally

discharges during shipping, so if it doesn't turn on, please charge it.

Mobile APP Installation

Download and install HDWifiCamPro, IOS is downloaded from Apple Store, Android

system is GooglePlay search.

For easy installation, please scan the QR code below to download the HDWifiCamPro

installation.

If your device cannot connect to GooglePlay, please scan the APK QR code below to

download and install.

Note: It is recommended to use a browser or third-party QR code scanning software

to scan and download the App.

(Note: All permissions must be turned on when downloading the APP)

Summary of content (7 pages)

PAGE 1
Wireless Security Camera User Guide If you have any problems, please contact us without hesitation! We will reply your messages within 24 hours to help you solve the problem. Forward 1. After turn on the camera，please reset it first . Reset: Press and hold the Mode button of the camera for about 5 seconds, during which the red indicator light will flash rapidly, release the button, wait for the indicator light to flash steadily and the reset is successful. 2.
PAGE 2
Product Buttons and Indicators Description ON/OFF MODE Switch button, click the button to turn on, press the button for a while to turn off Press and hold for 5 seconds to restore factory settings, and disconnect the network connected to the camera Lights up when charging, turns off when fully charged Charging indicator (blue light) Work indicator Blinking/steady light is the power-on state (red light) Network indicator (red light) 1. Slow flash, AP hotspot mode 2.
PAGE 3
2. On the WIFI connection page, select “ ( DGO*****”, “DBG*****”, “HTM*****” , "TUT*****") WIFI hotspot and connect. After the connection is successful, return to the App, and the device is added successfully (If the APP does not automatically add a device, you can click Search to add the searched device). The mobile phone will remind you whether to switch the network, be sure to keep the connection / do not allow switching. 3.
PAGE 4
Set the camera to connect to WIFI 1. Click the Settings button on this interface to open the Camera Setting page. 2. Select "WiFi", select the name of the Wi-Fi you want to connect to, enter the password of the Wi-Fi, and press the Sure button to connect. Note: After saving, the camera is in the WiFi network state, and the camera App is online after 30 seconds (the red light of the device is always on). If the camera is close to the router, the WiFi signal will be better.
PAGE 5
1. screen flips up and down 2. screen flips left and right 3. infrared switch 4. resolution 5. full screen 6. camera indicator switch 7. speaker 8. take photos 9. manual recording video 1. event 2. videos and remote Manually recorded videos and remote automatic recorded videos will be saved here. Please download important files to your mobile phone in time to avoid file damage. 3. album 4.
PAGE 6
1. wifi connection 2. user infomations 3.Record: micro SD card 4. Restart 5. Reset the device 6. QR code and camera ID Scan or enter them for share the camera. 1 “Add online camera” on the other device (Picture 1) 2 Scan the QR code on the main device (Picture 2) 3 Cam ID shows up and click “Sure” (Picture 3) 4 Connect the camera to Wifi on the main device (Picture 4), the camera will be restarted. After that, the other device can connect to the camera.
PAGE 7
FAQ: 1. When using this product for the first time, please fully charge the product. 2. The remote video is stuck: Please select the appropriate resolution according to the network environment. 3. SD card does not save video: You must format the SD card for the first time. 4. Forget the username or password: The default password of the camera is 6666. If you forget the username or password, you can restore the camera to the factory settings and reset the username and password. 5.