TOYOTA Scion FR-S Preparation ! ! Kit Contents: OEM Audio Plus FR-S System 400 Item 1 Item 2 Item 6 Item 7 System 400 Item 3 Item 8 Item 4 Item 5 Item 9 Item 10 ! Tools Recommended Hardware Content Item Quantity 1 2 2 1 3 1 4 1 ! Description 1” Soft Dome Tweeter with Neodymium Magnet 8” Carbon Fiber Subwoofer in Custom Fit Sealed Enclosure (with Amps Attached) Amplifier Module (See Item 2) (1) DSP Amplifier (1) Subwoofer Amplifier Quick-Sync Harness 5 1 6 7 1 1 8 1 9 1 10 1
TOYOTA Preparation ! Scion FR-S ! System 400 Table of Contents I. Preparation.....................................................................................................................................................1-2 1. Table Of Contents.............................................................................................................................. 2 II. Procedure....................................................................................................................
TOYOTA Procedure! Scion FR-S ! System 400 1. Vehicle Preparation a. Apply parking brake. b. Open the trunk and hood of the vehicle. c. Disconnect the negative (-) battery cable. d. Prepare a protective surface to place all vehicle components on.!! ! 2. Tweeter Installation a. Remove dash speaker grills 1. Very carefully disengage the speaker grill on the dashboard using a plastic panel or pick tool. Once loosened lift straight up then away to remove. (Fig. 2-1) 2.
TOYOTA Procedure! Scion FR-S ! System 400 5. Connect the tweeter connector and make sure it is secured with built-in locking tab. 6. Install the speaker grill by sliding the back end in first. (Fig. 2-6) 7. Push the front side of the speaker grill straight down until it snaps back into place. (Fig. 2-7) 8. Repeat steps 1-7 for the other tweeter. 3. Radio Removal 1. Make sure you have a protective blanket over the center stack/transmission area to protect from scratches during radio removal. (Fig.
TOYOTA Procedure! Scion FR-S ! System 400 3. Use a 10mm socket to remove the (4) bolts securing the radio. (Fig. 3-3) 4. All radio connectors have a locking tab that you must push down to disconnect. Carefully remove each connector then set the radio aside. (Fig. 3-4) 4. Quick-Sync Harness Installation a. Remove Driver and Passenger Side Threshold Panel 1. Disengage both ends of the threshold panel by spreading the edges. Very carefully pull straight up to remove. Repeat for other side. (Fig. 4-1) .
TOYOTA Procedure! Scion FR-S ! System 400 2. Carefully pull the kick panel to the right towards the pedals (Two small snaps secure it). Check for green snaps that may not have came off with the kick panel. Re-insert the green snaps to the kick panel if any. (Fig. 4-3) c. Remove Driver and Passenger Side Rear Panels 1. Loosen weather-stripping by hand and remove carefully in an outward direction. (Fig. 4-4) 2. Use a 10mm socket to remove the bolt securing the bottom seat cushion. (Fig. 4-5) 3.
TOYOTA Procedure! Scion FR-S System 400 ! 4. Use a plastic panel tool to remove the push in snap at the bottom of the rear panel. (Fig. 4-7) ! ! 5. Located in the trunk area, pull both backrest release straps to fold the backrest down. (Fig. 4-8) Fig.&5(9& 6. Use a plastic panel tool and remove the two push in snaps at the rear of the panel. (Fig. 4-9) 7. Carefully disengage the snaps one by one and pull the rear panel towards you and away to remove.
TOYOTA Procedure! d. Scion FR-S ! System 400 Route the Quick-Sync Harness 1. Use a utility knife and cut a U-shaped slot approximately 1” wide and 2” high in the area located in this picture on the passenger side trunk panel. This will provide access for the harness plugs to the amplifiers. (Fig. 4-11) 2. Remove the trunk carpet and trunk floor board. (Fig. 4-12) 3. Use a plastic panel tool to remove the three push in snaps securing the foam support between the back seat and spare tire. (Fig.
TOYOTA Procedure! Scion FR-S ! System 400 5. Lift the foam support up and fold it over so it rests on top of the rear seat back rest. (Fig. 4-15) 6. Disconnect the 10-pin factory amp connector. (Fig. 4-16) 7. Run the Quick-Sync harness’ amplifier connectors through the 1”x 2” slot. Pass through one connector at a time. (Fig. 4-17) 8. Using the factory ground located behind the rear passenger side trim panel, remove the 10mm ground bolt and install the harness ground together with the factory ground.
TOYOTA Procedure! Scion FR-S ! System 400 9. Run the ground wire with exiting factory wire and secure using the provided cable ties. (Fig. 4-19) 10. Route the harness through the channel provided under the foam support. (This will allow the foam support to be re-installed properly). (Fig. 4-20) 11. Connect the factory male amp connector to the female connector from the Quick-Sync harness. (6-pin connector does not need to be plugged). (Fig. 4-21) 12.
TOYOTA Procedure! Scion FR-S ! System 400 16. Lift carpet by disengaging the white plastic clips in the driver side threshold area and continue routing the harness underneath the carpet towards the driver sidekick panel area. Reinstall carpet clips and weather-stripping. (Fig. 4-23) 17. Route the Quick-Sync harness under the driver side dash and towards the radio cavity. (The two yellow power wires must remain separate in the driver-side kick panel for now).
TOYOTA Procedure! 5. Scion FR-S ! System 400 Amplifier and Subwoofer Installation a. Amplifier Connection 1. Plug the white 22-pin connector to the upper receptacle and the gray 22-pin connector to the lower receptacle of the DSP Amplifier (larger amp). Plug the black 10-pin connector to the bottom receptacle on the Sub Amplifier (smaller amp). IMPORTANT: Make sure all connectors are fully inserted and securely locked (listen for a locking click – Pull on harness lightly to confirm secure connection).
TOYOTA Procedure! Scion FR-S ! System 400 4. Install and position the speed clip so that it aligns with the top hole on the 2-hole bracket. (Fig. 5-5) ! 5. Place the subwoofer enclosure in position and install the ¼-20 x 2 ½” hex screw with washer on the backside to secure the enclosure. (Shifting the enclosure may be necessary to align holes). Do not fully tighten yet. (Fig. 5-6) 6. Install the ¼-20 x 1 ½” hex screw with washer on the front side of the enclosure. (Fig. 5-7) 7.
TOYOTA Procedure! Scion FR-S ! System 400 2. Return to the driver side under-dash and route the two yellow power wires through the firewall grommet (lubricate accordingly to prevent binding). Run the entire length of power wire then pull it back one inch and apply a bead of silicone sealant to the wire. Push the wire with silicone to seal the opening. (Fig. 6-2) 3. Install the 1/4" corrugated split loom onto to the power wires. Run the entire length to the firewall grommet. (Fig. 6-3) 4.
TOYOTA Procedure! Scion FR-S System 400 ! 2. Insert 12 ga. Power Wire into Yellow butt connector. Insert 14 ga. Power Wire into Blue butt connector. Crimp and apply heat to both butt connectors to activate the solder and heat shrink insulator for the best connection possible. (Fig. 7-2) 8. Fuse Installation a. Insert the 20A fuse for the 14 ga. power wire (thinner wire) and the 30A fuse for the 12 ga. power wire. (Fig. 8-1) 9. Connect Battery ground (-). (Fig. 9-1) 10. Set Clock to correct time.
TOYOTA Procedure! Scion FR-S ! System 400 2. Select "Natural" setting in the SSP Menu. (Fig. 11-2) (Pg 9 Radio owner’s manual) b. Pioneer Premium Radio (PT546-00121) 1. Turn radio on and select "Car Type" > "tC" in "System settings" (Fig. 11-3) (Pg 57 Radio owner manual) NOTE: Setting Car type to FR-S will result in a balanced sound reproduction. 2. Select "Natural" setting in the "SSP Menu" (Fig. 11-4) (Pg. 57 Radio owner manual) c. Aisin SNS 200 (NSDA-W10U) 1.
TOYOTA Procedure! Scion FR-S ! System 400 2. Verify "Parametric EQ" is set to "Flat" (Fig. 11-6) (Pg 185 Radio owner manual) 3. Verify the Fader/Balance settings are centered. (Fig 11-7) 4. Verify the Focus settings are centered. (Fig. 11-8) 12. This concludes the OEM Audio Plus System 400 | Scion FR-S Installation a. Start your engine. b. Turn on your radio. c.
TOYOTA Procedure! Scion FR-S ! System 400 Checklist –These points MUST be checked to ensure a quality installation.! Check: Power Windows Vehicle Function Detail: Verify power window controls are functioning properly. Power Door Locks Hazard Lights Verify power door lock controls are functioning properly. Verify hazard lights are functioning properly. Clock Verify proper time on clock. Radio Verify radio is functioning properly.
