Digital (Enhanced) Overhead Stirrer User Manual OS40-Pro Digital Enhanced Overhead Stirrer OS20-Pro Digital Overhead Stirrer Please read the User Manual carefully before use, and follow all operating and safety instructions! www.scilogex.
Contents Preface…………………………………………………… Service…………………………………………………… Warranty ………………………………………………… 1.Safety Instructions …………………………………… 2.Proper Use …………………………………………… 3.Inspection …………………………………………… 3.1 Receiving Inspection …………………………… 3.2 Listing of Items ………………………………… 4.System assembly ……………………………………… 5.Trial Running ………………………………………… 6.Control and Display …………………………………… 6.1 Control…………………………………………… 6.2 Display ………………………………………… 7.Motor Protect and Overload Protection ……………… 8.Faults ………………………………………………… 9.
Digital (Enhanced) Overhead Stirrer Welcome to the “Digital (Enhanced) Overhead Stirrer User Manual ”. Users should read this Manual carefully, follow the instructions and procedures, and be aware of all the cautions when using this instrument. Please provide the customer care representative with the following information： • Serial number（on the rear panel） • Description of problem (i.e.
Digital (Enhanced) Overhead Stirrer 1.Safety Instructions • Warning! • Read the operating instructions carefully before use. • Ensure that only trained staff works with the instrument. • • Protective ground contact! • En s u r e t h e s o c ke t m u s t b e g r o u n d e d (protective ground contact) before use.
Digital (Enhanced) Overhead Stirrer 2.Proper use 3.2 Listing of Items The instrument is designed for mixing sticky substance in schools, laboratories or factories. It can be installed on a variety of impeller, for different viscosity of the medium. This instrument is not suitable for using in residential areas or other constraints mentioned in Chapter 1. Do not use the accessories recommended by the manufacturer, or failure to use the instructions, may be caused unsafe situation.
Digital (Enhanced) Overhead Stirrer 4.System assembly a.Install stand The stand must be assembled according to the following instructions. Adjust the height of the main unit, and the distance from main unit to the support holder by rotating the locking device. Anti-drop protector can be adjusted up or down, ensure the locking position is suitable for fixing the main unit, and then attach the main unit to the stand. b.Install stirring impeller Plug the stirring impeller into the drill chuck.
Digital (Enhanced) Overhead Stirrer Note: Do not touch components of high-speed running instrument during operation to avoid damage and harm. 6.Control and Display Items Default settings Speed control button Speed Set stirring speed, press the button to start/stop stirring function. Mode switch knob Mode 6.1 Control Figure 3 6 Shift speed and torque display. LCD displays the current speed value at initial running; LCD displays the current torque value when press the mode knob.
Digital (Enhanced) Overhead Stirrer Power switch /Overload protection light Power/Overload Green/Red LED display light. LED light shows green when switch on, LED light shows red when starts overload protection. When the torque reaches limited value, overload protection function will be started. At the same time overload protection light flashes, while the system stops running. Drill chuck Can be held stirring impellers. Power switch I/O Switch ON or OFF the instrument.
Digital (Enhanced) Overhead Stirrer original setting speed value to start stirring function. The overhead protection still continues starting if the above method used, please contact manufacturer/supplier. 7.Motor protection and overload protection Overhead Stirrer works continuous, the motor current is electronically limited to achieve security stall and overload protection.
Digital (Enhanced) Overhead Stirrer • Do not remove the power line when cleaning. Only use 9.Interface and output recommended cleansers: Overhead stirrer makes use of special accessories and cables to connect external devices. Standard 9-pin interface is used to be connected to the PC. • selected from the specified communication line of the EIA-standard RS232C, corresponding with DIN66020. • Transmission method: Asynchronous signal transmission in start-stop-operation.
Digital (Enhanced) Overhead Stirrer 11.Associated standards and regulations Power [W] Max. stirring quantity (H2O) [L] Construction in accordance with the following safety standards: Motor rating input[W] EN 61010-1 UL 3101-1 CAN/CSA C22.
Digital (Enhanced) Overhead Stirrer Max. viscosity [mPas] 50000(Enhanced model) 10000 Chuck range diameter [mm] 0.5-13 Dimension[W x H x D] [mm] 83x220x186 Weight[kg] 3.5(Enhanced model) 2.5 Temperature[℃] 5-40 13.Ordering information Cat No. Descriptions OS40-Pro, Digital Enhanced Overhead Stirrer(Exclude universal stand), 840203019999 Max. stirring quantity 40L, USA plug, 110V/220V/50Hz/60Hz OS40-Pro, Digital Enhanced Overhead Stirrer(Exclude universal stand), 840203119999 Max.
Digital (Enhanced) Overhead Stirrer OS20-Pro, Digital Overhead Stirrer(Exclude universal stand), 840103219999 Max. stirring quantity 20L, Euro plug, 110V/220V/50Hz/60Hz OS20-Pro, Digital Overhead Stirrer(Exclude universal stand), 840103319999 Max. stirring quantity 20L, UK plug, 110V/220V/50Hz/60Hz 18900076 Straight stirrer, PTFE-coated 18900077 Blade stirrer, PTFE-coated 18900078 Centrifugal stirrer, PTFE-coated 18900069 Drill chuck 18100319 9-Pin interface line, suitable for OvaPC software.
SCILOGEX, LLC 500 Four Rod Road Suite 122 Berlin, CT 06037 USA Tel：1- (860) 828-5614 Fax：1- (860) 828-5389 E-mail: info@scilogex.com Website：Http://www.scilogex.
