MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer User Manual MS-H-Pro Digital Hotplate Magnetic Stirrer MS-Pro Digital Magnetic Stirrer Please read the User Manual and the related Video of this instrument on our website carefully before use, and follow all operating and safety instructions! The website www.scilogex.com Cat No.
8.2 Residual Heat Warning（HOT） 8.3 Setting the Safety Temperature 9 Function: Stirring 9.1 Basic Stirring 9.2 Stirring Bar Breakaway Monitoring 10 Remote Control 11 Faults 12 Maintenance and Cleaning 13 Associated Standards and Regulations 14 Technical Data 15 Products andAccessories 16 Main Spare Parts 16.1 Spare Parts Diagram of MS-(H)-Pro 16.2 List of Spare Parts of MS-(H)-Pro Contents Contents Preface Service Warranty 1 Safety Instructions 2 Proper use 3 Inspection 3.1 Receiving Inspection 3.
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer Welcome to the “MS-(H)-Pro Digital（Hotplate） Magnetic Stirrer User Manual”. Users should read this Manual carefully, follow the instructions and procedures, and beware of all the cautions when using this instrument. Please provide the customer care representative with the following information： • Serial Number（on the rear panel） • Description of problem (i.e.
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer 1 clean, non-slip, dry and fireproof surface, do not operate the instrument in explosive atmospheres, with hazardous substances or under water. • Gradually increase the speed, reduce the speed if : - The stirring bar breakaway because of too high speed - The instrument is not running smoothly, or container moves on the base plate. • Temperature must always be set to at least 25 ℃ lower than the fire point of the media used.
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer components. Safe operation is only guaranteed with the accessories described in the “Accessories” chapter. Accessories must be securely attached to the device and cannot come off by themselves. Always disconnect the plug before fitting accessories. • Ensure that the external temperature sensor is inserted in the media to a depth of at least 20 mm. • When using metal vessels, do not place the temperature sensors on the bottom of the vessel.
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer 3 • Ensure the power be off • Plug in the power cable，ensure the power be on and begin initializing. • Add the medium into the vessel with a stirring bar. • Put the vessel on the workplate. • Set the rated stirring speed and start stirring. • Observe the stirring bar and LCD display. • Set the rated temperature and start heating. • Observe the real temperature on LCD display. • Stop the heating and stirring functions.
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer 5 Control and Display Items Speed control knod Stir 5.1 Control elements LED Heat (MS-H-Pro) Descriptions Set the rated rotary speed. The function “Stirring” is switched ON or OFF via push the knob. Temperature control Set the rated temperature. The function knob “heating” is switched ON or OFF via Heat push the knob. (MS-H-Pro) Mode Key Shift among the three operating modes: Mode A, B, and C mode.
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer 5.2 Display Real value Note: If both heating and stirring functions have been started at the same time, the display of function “heating” always has higher priority. If in this case speed is changed via the stirring knob, it display stirring speed and reverses to temperature in the duration of 5 seconds.
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer Items Operating mode Setting temperature (°C ) SAFE (℃ ) Setting rotary speed (rpm) Residual heat warning Stirring bar breakaway monitoring Table 4 stirring bar breakaway monitoring can be set in this mode. Default settings A 25 350 100 On OFF Operation mode B MS-H-Pro has heating and stirring functions. Users can control on the front panel or by remote PC.
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer Operation mode B before the device is switched ON. • Ensure the external temperature sensors connecting firmly before heating. • Set the temperature via turnning the temperature control knob slowly to the ideal scale . • When the heating function is switched on, the LED “Heat” will light up and the LCD will display the real temperature. • The rated temperature will be displayed on the right-hand side of the LCD as well as Temp and °C characters.
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer In the B mode, if the external temperature sensor is not plugged in, “Probe” will flash. If plugged in, “Probe” will be shown on the digital display to indicate that the sensor is operating. The external temperature sensors’ value and actual temperature are displayed. Compared with the temperature control of the hotplate, the external temperature sensor can control the medium’s temperature more precisely.
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer set. Breakaway can occur when stirring at high speeds , when large stirring bars are being driven at speeds close to the maximum magnetically torque or sample viscosity changes. Using MS-(H)-Pro, stirring bar breakaway monitoring function can be set at the rotary speed range between 300 and 1500 rpm. When stirring bar breakaway is detected, stirring is stopped immediately to enable the stirring bar to be picked up.
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer in start-stop-operation. • Mode of transmission: Fully Duplex. • 1 start bit; 7 character bits; 1 parity bit [straight (even]); 1 stop bit. • Transmission speed: 9600 bit/s NOTE: Forbid to plug in or plug out the RS 232C communication line! 10 Remote control 11 Faults Figure 6 The unit can be controlled from an external PC (using the dedicated software) via the RS232 C serial interface fitted to the unit.
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer • Heating cannot be started when push the temperature control knob, or stirring cannot be started when push the speed control knob. - Check whether the unit is in the mode setting program, - Exit from the mode setting and restart the heating/ stirring functions. • Unit cannot be powered off when switched off. - Check if the residual heat warning function is still ON and hotplate temperature is above 50℃ (the LCD still work and “Hot” flash).
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer 13 Associated standards and regulations Stirring point position quantity Max. stirring quantity (H2O) [L] 20 Construction in accordance with the following safety standards: EN 61010-1 UL 3101-1 CAN/CSA C22.2(1010-1) EN 61010-2-10 Construction in accordance with the following EMC standards: EN 61326-1 Associated EU guidelines: EMC-guidlines: 89/336/EWG Instrument guidelines: 73/023/EWG 14 1 Max.
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer The safety temperature range of the hotplate [℃] 100~350(MS-H-Pro) 811123029999 MS-H-Pro Digital Hotplate Magnetic Stirrer ，Porcelain enamel,USA plug, 110V/50Hz/60Hz 811123039999 MS-H-Pro Digital Hotplate Magnetic Stirrer ，Stainless Steel, Cn plug, 220/50Hz/60Hz 811123049999 MS-H-Pro Digital Hotplate Magnetic Stirrer ，Stainless Steel, USA plug, 110V/50Hz/60Hz 811123059999 MS-H-Pro Digital Hotplate Magnetic Stirrer ，Porcelain enamel, Euro plug, 220/50Hz/
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer 811113019999 MS-Pro Digital Magnetic Stirrer ，Stainless Steel，Cn plug, 220V/50Hz/60Hz 18900009 Stirring bars（25mm x 8mm），1pcs/pk Stirring bars（30mm x 6mm），1pcs/pk 811113029999 MS-Pro Digital Magnetic Stirrer ，Stainless Steel，USA plug, 110V/50Hz/60Hz 12500005 18900011 Stirring bars（40mm x 8mm），1pcs/pk 12500004 Stirring bars（50mm x 8mm），1pcs/pk 811113039999 MS-Pro Digital Magnetic Stirrer ， Stainless Steel，Euro plug, 220V/50Hz/60Hz 18900013 Stirring b
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer 16.2 List of spare parts 16 Main spare parts 16.1 Spare parts diagram 18 19 20 1 2 3 4 17 16 15 14 13 5 12 11 6 10 9 8 Figure 8 7 No Name No.
SCILOGEX, LLC 500 Four Rod Road Suite 122 Berlin, CT 06037 USA Tel：1- (860) 828-5614 Fax：1- (860) 828-5389 E-mail: info@scilogex.com Website：Http://www.scilogex.
