BlueSpin (Hotplate) Magnetic Stirrer User Manual MS-H280-Pro BlueSpin LED Digital Hotplate Magnetic Stirrer MS-PA BlueSpin LED Digital Magnetic Stirrer MS-PB BlueSpin Classic Magnetic Stirrer Please read the User Manual carefully before use, and follow all operating and safety instructions! www.scilogex.
Contents Preface ................................................................................. 1 Service ................................................................................. 1 Warranty .............................................................................. 1 1. Safety Instructions ....................................................... 2 2. Proper Use ................................................................... 3 3. Inspection ..................................................
BlueSpin (Hotplate) Magnetic Stirrer Please provide the customer care representative with the Preface following information: • Serial number(on the rear panel) • Certification • Description of problem (i.e., hardware or software) • Methods and procedures adopted to resolve the problems • Your contact information Welcome to the “BlueSpin (Hotplate) Magnetic Stirrer”.
BlueSpin (Hotplate) Magnetic Stirrer substances or under water. • Gradually increase the speed, reduce the speed if: - Stirring bar breaks away due to high speed - The instrument is not running smoothly, or container moves on the base plate • Temperature must always be set at least 50℃ lower than the fire point of the media used.
BlueSpin (Hotplate) Magnetic Stirrer • The instrument can only be disconnected from the main power supply by pulling out the main or the connector plug. • The voltage stated on the label must correspond to the main power supply. • Ensure that the main power supply cable does not touch the hotplate. Do not cover the device. • The instrument may only be opened by experts. • Keep away from high magnetic field. 2.
BlueSpin (Hotplate) Magnetic Stirrer 3. Inspection 4. Control 3.1 Receiving Inspection 4.1 Control elements Unpack the equipment carefully and check for any damages which may have arisen during transport. Please contact manufacturer/supplier for technical support. Probe ( Hotplate model ) Note: If there is any apparent damage to the system, please do not plug it into the power line. LED Display 3.
BlueSpin (Hotplate) Magnetic Stirrer LED Display Speed Control Knob Speed Control Knob Figure 4 Classic model Figure 3 Digital model Figure 5 5
BlueSpin (Hotplate) Magnetic Stirrer Items Descriptions Temperature Control Set the temperature parameters. The function “heating” is switched ON or Knob Heat Digital hotplate model Speed Control Knob Stir LED Display Probe Power Switch Temperature Control Digital model Classic model Knob Stir OFF via push ON/OFF knob. Set the rotary speed. The function “Stirring” is switched ON or OFF via push ON/OFF knob. LED displays the real working state and all settings.
BlueSpin (Hotplate) Magnetic Stirrer 4.2 Display Figure 7 Digital model Figure 6 Digital hotplate model Characters Temperature display area Speed display area Characters Speed area Descriptions When heating function was switched ON, LED displays the temperature setting value and shifts to real value in 5 seconds. When the heating function is switched OFF and the hotplate temperature is still above 50°C, LED displays “Hot”, otherwise LED displays OFF.
BlueSpin (Hotplate) Magnetic Stirrer 5. Trial Run 6. Function: Heating (Digital hotplate model ) • Make sure the required operating voltage and power supply voltage match. • Ensure the socket must be properly grounded. The device is controlled by digital temperature control technology, which has two separate safe circuits. The hotplate is kept at a constant temperature by a digital control circuit. The hotplate temperature can also be monitored from a separate, adjustable safe circuit.
BlueSpin (Hotplate) Magnetic Stirrer heating function will be stopped automatically under abnormal conditions. Please operate follow the instructions below: ‐ Hotplate center and outer edge. ‐ The sample in the vessel and hotplate surface. In order to ensure the accuracy of the temperature inside the container, please use the external temperature sensor PT1000. • • 6.1 Working with external temperature sensor Switch OFF the instrument.
BlueSpin (Hotplate) Magnetic Stirrer 7. Stirring 8. Faults The function “stirring” of LED digital model is switched on or off via pushing on/off speed control knob. The speed range of 100 to 1500 rpm and in steps of 10 rpm. The function “stirring” of classic model is switched on or off via rotating speed control knob. The speed range of 0 to 1500 rpm.
BlueSpin (Hotplate) Magnetic Stirrer 9. Maintenance and Cleaning • Proper maintenance can keep instruments working properly and lengthen its lifetime. • Do not spray cleanser into the instrument when cleaning. • • Unplug the power line when cleaning.
BlueSpin (Hotplate) Magnetic Stirrer Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
BlueSpin (Hotplate) Magnetic Stirrer Specifications Items Plate material Digital model Specifications Classic model Items Digital model *Ceramic coated/Plastic Dimensions of workplate (mm) φ135 φ135 *Heating power [W] 500 - RT-280, increment:1 *Temperature display [°C] 220×160×75 Weight [kg] *1.4/0.7 0.7 Permitted ambient temperature [°C] 5-40 - Permitted relative humidity 80% LED - Protection class acc.
BlueSpin (Hotplate) Magnetic Stirrer 50Hz/60Hz 12. Ordering Information Cat No.
BlueSpin (Hotplate) Magnetic Stirrer 861521239999 MS-PA, BlueSpin LED Digital Magnetic Stirrer, Euro plug, 100-240V, 50Hz/60Hz 861521339999 MS-PA, BlueSpin LED Digital Magnetic Stirrer, UK plug, 100-240V, 50Hz/60Hz 18900148 Support clamp of PT1000 18900080 Reaction block for 50ml round bottom flask(one flask capacity) 18900081 Reaction block for 100ml round bottom flask(one flask capacity) 18900082 Reaction block for 250ml round bottom flask(one flask capacity) 18900083 Reaction block for 500m
SCILOGEX, LLC 500 Four Rod Road Suite 122 Berlin, CT 06037 USA Tel: 1-860-828-5289 Fax:1-860-828-5389 E-mail: info@scilogex.com Http://www.scilogex.