Record Your Model Number: _______________________________________________________ Record Your Serial Number: _______________________________________________________ Record Your Date of Purchase: _______________________________________________________ SCIFIT • Scientific Solutions for Fitness • SCIFIT • Scientific Solutions for Fitness • SCIFIT • Scientific Solutions for Fitness • SCIFIT
Important Safety Instructions Read all instructions before using your SCIFIT exercise machine! Save these instructions! Danger! To minimize risk of electric shock: Warning! To reduce risk of burns, fire, electric shock, or injury to persons: SCIFIT • Scientific Solutions for Fitness • SCIFIT • Connect to a dedicated, properly grounded outlet only. See Power Requirements below. Also, always unplug this appliance from the electrical outlet immediately after using and before cleaning. 1.
Directives de sécurité importantes Lire toutes les directives avant d’utiliser l’appareil SCIFIT ! Conserver les présentes directives ! Danger ! pour minimiser les risques Raccorder l’appareil uniquement à une prise adéquatement mise à la terre. Se reporter à la section Alimentation requise ci-dessous. Il faut également débrancher l’appareil de la prise électrique immédiatement après son utilisation et avant sa maintenance.
Important Safety Instructions Power Requirements – AC5000 and AC5000M (220V) Plug Configuration Provided Separately. 1. SCIFIT’s AC5000 and AC5000M treadmill requires a 208-265 Volt/15 AMP dedicated circuit. The circuit must have a minimum of 12 gauge wire. A dedicated circuit is a power outlet reserved for the exclusive use of your treadmill. This requires a power line to be routed from the main breaker box or subpanel to the power outlet for the treadmill.
Directives de sécurité importantes Alimentation requise – 5000 CA (220 V) et 5000M (220V) 1. Les tapis roulants 5000 CA et (220 V) exigent un circuit spécialisé de 208-265 volts, 20 A ayant un calibre minimal de 12. Par circuit spécialisé, on entend une prise réservée pour l’usage exclusif du tapis. Il faut donc acheminer une ligne électrique du boîtier principal des disjoncteurs ou du panneau secondaire jusqu’à la prise du tapis. Aucun autre dispositif ne doit être branché sur la prise.
Table of Contents Introduction 1.1 to 1.2 Product Components 2.1 Assembly 3.1 to 3.8 Setup 4.1 Installation and Maintenance 5.1 Treadmill Preventative Maintenance 6.1 Heart Rate Transmitter Strap 7.1 Program Descriptions 8.1 Keypad Functions 9.1 Detailed Program Instructions 10.1 to 10.4 Troubleshooting 11.1 Warranty Policy and Service Procedures SCIFIT • Scientific Solutions for Fitness • SCIFIT • Scientific Solutions for Fitness 12.1 to 12.
Introduction 1.1 Thank you for your purchase of the SCIFIT treadmill. We have incorporated the finest technology and ergonomic design into this machine to assist you in achieving your fitness goals. However, for your safety, please adhere to the following recommendations before you begin to exercise. Fit-Key™ Your SCIFIT treadmill is equipped with a Fit-Key receptacle. Contact SCIFIT to learn more about the Fit-Key exercise protocol and documentation software.
Introduction 1.2 Safe Use of Treadmill • The safest position is with your feet on each top side frame, straddling the running belt. Step onto the running belt after you have started the treadmill to prevent injury. • To balance yourself look straight ahead and hold on to the siderail or handlebars. • It is common to feel slightly dizzy after getting off the treadmill after a workout. This is because the ground has been moving under you.
Product Components 2.1 � 1. External component and name � ������� ������������ ������������������� ������������������� ����������������� ���������� �������������������� ��������� ������������ ��������� ������������ ���������� ��������� ��������� 2.
Assembly 3.
Assembly 3.2 � ����� �������������� ��������������� � � � � � � � ���� �� �� ��� � � ������� � � � � � � � � � � � Setup 4.1 Assembly The treadmill comes pre-lubricated and ready to use. Some treadmills are shipped with the handlebars removed. To assemble, follow the assembly procedure provided separately. Caution: Do not run power cord under treadmill to avoid damage to the power cord by the belt or elevation racks.
Assembly 3.
Assembly 3.4 1.
Assembly 3.5 2. Install middle frame Inverter Cable Actuator Cable Speed Handle Switch Cable Incline Handle Switch Cable Pic#3 1 STEP Install the inverter cable, actuator cable, incline handle switch cable and speed handle switch cable through the middle frame Pic#4 2 STEP Adjust four M8 bolts and washers tightly.
Assembly 3.
Assembly 3.
Assembly 3.
Setup 4.1 Moving The treadmill has wheels attached to the front of the motor end for easy handling. These built-in wheels are designed for short distance relocation of the treadmill, not for moving or delivery. To move a short distance, elevate to 10%, unplug from wall outlet, lift rear of treadmill, then move. Please use a platform dolly to move the treadmill longer distances. SCIFIT Treadmill Settings Table These settings enable the club owner/manager to customize certain features of the treadmill.
Installation and Maintenance 5.1 Placement Avoid placing the treadmill in direct sunlight, in areas of extreme temperature or humidity, or where the equipment may be splashed with any fluid. This treadmill is intended for indoor use only. Position treadmill so the plug is easily accessible. Allow a minimum of 20” or 50cm between treadmill and wall or other treadmills. Position the equipment so the plug is easily accessible. Deck Maintenance The treadmill deck is prewaxed and needs minimal maintenance.
Treadmill Preventative Maintenance 6.1 After intense training, always clean your SCIFIT product. Perspiration that stays in contact with the frame, casings, and control panel may cause rust or other damage. Clean surfaces with water and mild soap. Dry with a towel. Follow the Schedule below to maintain optimal performance of a SCIFIT treadmill. Weekly Clean exterior • Wipe the control panel with the damp cloth – do not spray liquid directly on it. • Clean the machine with water and mild soap.
Heart Rate Transmitter Strap 7.1 Uses of the Heart Rate Transmitter Strap Size Adjuster The wireless heart rate transmitter strap accessory is a useful device if you desire continuous feedback on your current heart rate during a workout. The Heart Rate Control program enables the user to set-up a target heart rate.
Program Descriptions 8.1 SCIFIT treadmills offers exercise programs: Manual, Heart Rate Control and several different Profile programs. A description of each exercise program is summarized in this section. The Quick Start Manual program allows the user to adjust the speed or elevation to a desired setting. This setting will not change unless the user manually increases or decreases the speed or elevation using the UP or DOWN arrow keys.
Keypad Functions 9.1 START Key Starts the treadmill. STOP/CLEAR Key When pressed during a workout, this key stops the treadmill in a pause mode. Press STOP a second time to clear the program, or press START again to continue the program. SPEED AND ELEVATION UP and DOWN ARROW Keys Adjust speed and elevation as desired. ENTER Key Press ENTER after choosing the desired program, speed, time or target heart rate. SELECT Key Press SELECT to set the multifunction display in desired display mode.
Detailed Program Instructions 10.1 Step-by-Step Instructions for Operating the Manual Quick Start Program: Press START Press START. The treadmill will start at the minimum speed and elevation. The time will begin counting up from zero. Adjust Speed Adjust speed as desired with the UP or DOWN ARROW keys. Adjust Elevation Adjust elevation as desired with the ELEVATION UP or DOWN ARROW keys.
Detailed Program Instructions 10.2 Step-by-Step Instructions for Operating the Heart Rate Control Program Put on the Heart Rate Transmitter Strap The Heart Rate Transmitter Strap is required for this program. Refer to Section 4-1, Heart Rate Transmitter Strap, for a complete set of instructions on using the strap. Without transmitter strap, the Heart Rate Control Program will shut down. The Heart Rate Control Program will not operate with the contact pulse grip system.
Detailed Program Instructions 10.3 Step-by-Step Instructions for Operating a Hill/Speed Profile Program Select Program Push the PROGRAM key until the desired hill/speed profile is displayed. The respective profiles appear in the dot matrix window, speed on top, elevation on bottom. The selection includes elevation based programs and speed based programs. Once the desired program is displayed, press ENTER. Set Maximum Speed Set maximum Speed using the SPEED UP/DOWN KEYS.
Detailed Program Instructions 10.4 Step-by-Step Instructions for Operating the Reverse Mode (AC5000M only) Press REVERSE (AC5000M only) Press REVERSE when treadmill is in idle mode. ������� Press START Press START. The treadmill will start at the minimum speed (In the reverse direction) and elevation. The time will begin counting up from zero. Caution: Be prepared for belt to start in reverse direction. Adjust Speed Adjust speed as desired with the UP or DOWN ARROW keys.
Troubleshooting 11.1 CONDITION Main power does not turn on REASON SOLUTION Power cable is not connceted. Connect the powercord into plug.
Warranty Policy and Service Procedures SCIFIT Statement of Warranty 12.1 SCIFIT warrants, to the original purchaser, new products against defective workmanship and/or materials under normal and proper use subject to the following limitations.
Warranty Policy and Service Procedures 12.2 Freight and Shipping SCIFIT is NOT responsible for the repair or replacement of any unit or part damaged during transit or installation. Fire, flood and acts of God are NOT covered under this warranty. The customer is responsible for inspection of each unit and part for shipping damage at the time of delivery.
Warranty Policy and Service Procedures 12.3 Parts Supply During the first 30 days, warranty parts will be shipped via overnight delivery. Determination must be made before 2:00 p.m. Central Time on any given weekday for next day delivery. During the remainder of the first year warranty period, parts requirements will be filled second day air. Thereafter, parts will be supplied via ground shipment. The customer is welcome to request overnight or second day parts shipping at customer’s expense.
SCIFIT • Scientific Solutions for Fitness • SCIFIT • Scientific Solutions for Fitness • SCIFIT • Scientific Solutions for Fitness • SCIFIT
