User's Manual

Shadows cast by neighboring walls, trees and roof
overhangs should be avoided. Besides, the sun is lower
in the sky in winter, the winter shadow should be
avoided too where possible.
INSTALLATION AND TEST
1. Remove external power adapter or COM1 cable (if
any) from the WS-30S, and turn off the battery switch.
2. Release the mounting bracket from the back side of
the WS-30S by pulling the bracket downward from the
case.
3. Use the mounting bracket as a template, hold it against
the wall where the WS-30S is to be mounted, and
mark the positions of the three screw holes. Drill three
6mm (1/4in.) holes 1 inch deep. Insert the supplied
wall plugs and attach the bracket to the wall with the
screws.
4. Turn on the battery switch. Use the supplied screw
(4mm) to fix the WS-30S on the bracket, refer to Fig 4.
Then put the plastic cap on the cavity of the top cover.
5.
It’s a must to test RF range after installation
,
steps
as below.
A).On the LS-30 Base Unit, entering “Installer Mode”
and select \Set Siren\ Siren/Relay Test then press the
“YES” button, which will trigger the WS-30S to
generate a chirp if everything is correct.
B).Use a magnet to approach the right-bottom corner
of the WS-30S, you will hear a chirp from the WS-30S
and a beep from the LS-30 Base Unit if the distance is
OK.
Remark:
If the WS-30S is removed from the bracket,
or the housing is opened, the internal tamper switch
would activate the siren for 5 minutes, or until the
WS-30S is mounted on the bracket again. Meanwhile,
the WS-30S would send a RF signal of tamper
detection to the LS-30 Base Unit.
INDICATION
The reaction of the light and sound of the WS-30S varies
with the operation or alarm state as below,
-Power ON and code enroll: The WS-30S enters
ENROLL state for 30 seconds automatically when the
power is applied. Light stays ON continuously, until the
WS-30S learns a new code (2 chirps), or a 30-second
timeout expires (one chirp, no new code learnt).
-Alarm state:
Light flashes, and siren sounds
continuously. When alarm time expires, sound stops but
light keeps flashing until the LS-30 is disarmed by
Master/User press hotkey C (Clear) on the Base Unit.
SOUND TYPES
For the sake of easy identification of the alarm states, the
siren sounds differently with different alarm signals from
the LS-30 Base Unit.
:
Burglar Alarm, or WS-30S is
tampered (continuous tone)
:
Fire Alarm
:
Medical Alarm, Panic Alarm, Special
Sensor Alarm, Sensor Tampered
- -
:
LS-30 changes from Disarm to Arm
state (two chirps, see Note 2)
-
:
LS-30 changes from Arm to Disarm
state (single chirp, see Note 2)
Remarks:
1). “-“ means ON, the blank interval means Pause.
2). Assume that “Mode Change Chirp” and “Tamper
Siren” are set “ON” on the Base Unit.
3). Arm/Disarm chirp sound can be disabled by setting
jumper J10 to “Off” with only strobe remains.
LOW BACK-UP BATTERY
Back-up battery is monitored all the time, when low
battery is detected, the WS-30S would send Battery Low
RF signal to the Base Unit. And once the battery is
recharged by sunlight or external power, a “Battery Low
Restore” RF signal will be sent as well.
SPECIFICATIONS:
Power: 1W Solar panel
Internal rechargeable battery: Ni-MH 6V/1200mAH
Fully charged battery back-up time: 30 days
Current consumption: 1.5mA @standby,
170mA @activation
Siren output: about 115 dB (@30cm, facing the piezo
siren)
Strobe: Red or blue as required
Tamper protection: Activates when removing from the
bracket or opening the cover.
RF: 2-way radio.
IP Rating: 54 (with dust and splashing water protected
by proper installation)
Size: 90 x 233 x 190 mm
Weight: 730g
Maximum Strobe Light Viewing Angle
Mounting Bracket
Fig.4
Fig.5
Side view
To
p
view