MSDS

it can be done without risk to personnel. If possible, prevent runoff water from entering storm drains, bodies of
water, or other environmentally sensitive areas. Isolate from incompatible chemicals (see Section 10, Stability
and Reactivity), heat, sparks, electrical equipment, and open flame.
6. ACCIDENTAL RELEASE MEASURES
SPILL AND LEAK RESPONSE: Trained personnel using pre-planned procedures should respond to uncontrolled
releases. Proper protective equipment should be used. In case of a spill, clear the affected area and protect
people.
RESPONSE TO INCIDENTAL RELEASES: Personnel who have received basic chemical safety training can generally
handle small-scale releases, such as 1 container of this product. Respond to incidental chemical releases by
wearing gloves, goggles, and appropriate body protection.
RESPONSE TO NON-INCIDENTAL RELEASES: Respond to non-incidental chemical releases of this product, such as
the simultaneous puncturing of several containers, by clearing the impacted area and contacting appropriate
emergency personnel. Clean up should only be done by qualified personnel. Responders should wear the
level of protection appropriate to the type of chemical released, the volume of the material spilled, and the
location where the incident has occurred. Minimum Personal Protective Equipment should be Level B: triple-
gloves, chemical resistant apron, boots, and splash goggles and Self-Contained Breathing Apparatus. Level B
should also be used when oxygen levels are below 19.5% or are unknown.
RESPONSE EQUIPMENT AND PROCEDURES: Absorb spilled liquid with polypads or other suitable absorbent
materials. Decontaminate the area thoroughly. Prevent spill rinsate from contamination of storm drains, sewers,
soil or groundwater. Place all spill residues in a suitable container and seal. Dispose of in accordance with
applicable U.S. Federal, State, or local procedures or appropriate standards of Canada (see Section 13, Disposal
Considerations).
7. HANDLING and STORAGE
WORK PRACTICES AND HYGIENE PRACTICES: As with all chemicals, avoid getting this product ON YOU or IN YOU.
Wash thoroughly after using this product. Do not eat or drink while using this material. Avoid generating dusts,
mists or sprays of this product. Remove contaminated clothing immediately.
STORAGE AND HANDLING PRACTICES: All employees who handle this material should be trained to use it safely.
Open containers carefully on a stable surface. Empty containers can contain residual material; therefore,
empty containers should be handled with care. Store containers in a cool, dry location, away from direct
sunlight, sources of intense heat, or where freezing is possible. Store away from incompatible materials (see
Section 10, Stability and Reactivity). Keep container tightly closed when not in use. Inspect all incoming
containers before storage, to ensure containers are properly labeled and not damaged. Control possible sources
of ignition.
PROTECTIVE PRACTICES DURING MAINTENANCE OF CONTAMINATED EQUIPMENT: Follow practices indicated in
Section 6 (Accidental Release Measures). Make certain that application equipment is locked and tagged-out
safely if necessary. Collect all rinsates and dispose of according to applicable U.S. Federal, State, or local
procedures or appropriate Canadian standards.
NFPA 30B: Level 1 Aerosol.
8. EXPOSURE CONTROLS - PERSONAL PROTECTION
VENTILATION AND ENGINEERING CONTROLS: Use with adequate ventilation to prevent inhalation of vapors and
spray mists. Ensure exposure levels are maintained below the limits provided in Section 2 (Composition and
Information on Ingredients).
RESPIRATORY PROTECTION: If adequate ventilation can not be guaranteed, use NIOSH approved respirators to
control dusts, mists, fumes or vapors. Maintain airborne contaminate concentrations below guidelines listed in
Section 2 (Composition and Information on Ingredients). Oxygen levels below 19.5% are considered IDLH by
OSHA. In such atmospheres use of a full-face-piece pressure/demand SCBA or a full face-piece, supplied air
respirator with auxiliary self-contained air supply is required under OSHA’s Respiratory Protection Standard (29 CFR
1910.134).
EYE PROTECTION: For consumer use, wearing eye protection (such as safety glasses) is advisable. However, for
specific industrial applications, enhanced eye protection can be necessary. Use approved safety goggles or
safety glasses, as described in OSHA 29 CFR 1910.133. If necessary, refer to U.S. OSHA 29 CFR 1910.133, or