@ Preventative Maintenance Product Support Website: Guide www.nautilus.
Nautilus T9 Series Treadmills Daily • Inspect the power cord and wal[king belt for wear, , Check the position of the walking belt. Verify it does not rub against the frame, Evenly space the be,It on the deck within 0.25 inches of each side rail. Adiust the bek if necessary. • Check the optional side hand rails. Fasten them securely. , Remove potential hazards from the treadmill area. Cleaning Clean the treadmill on a regular basis he_ps to improve operation and increase component _ifespan.
Do not ove_ighten the walking heft. Be not torque adj_stment screws beyond _ in@s {9 N-M}. reduces the beff life and may damage the rolbr bearings. Adjusting 0ve_ightening Belt Tension Adiust the heft tension whenever the heft s_ips or moves unsteadily during operatiom 1. Loosen the _o adiustment bolts (See Rgore 1}. 2.
Oonotcutthebe_t.Doingso can cause Adjusting the rear rol_er to fall and snap the alignment pins on the end c:ap. Belt Tracking Adiust the be_t tracking whenever the belt moves to one side or the other. Stay off the bek when adiu_ments. 1. Sta_ the treadmill at minimum speed and grade. 2, Increase speed to 6 m#h. Make the following 2=1 If the belt moves to the right: turn the right adia_ment bok 1/4-tam c_ockwise. 2=2 If the belt moves to the left: turn the _efl adiu_ment bok 1/4°turn clockwise. 3.
Nautilus U916/R916 Ro ati n ÷ M a i nt ÷ na n c ÷ Upon receiving your machine, use a soft, clean towel to wipe off the dust, which may have accumulated during shipping. Your new machine will require minor assembly, Refer to the "lnsta]lation Instructions" section for details. Cleaniag 1. DO NOT USE G_SS CL_NERS with a water-dampened 2. OR ANY OTHERHOUSEHOLD CLEANERS ON THE CONSOLE. C_eanthe console daily cloth and wipe dry after cleaning.
Chat:king the Battery Charge Using your multimeter, touch the red lead to the positive termina_ of the battew and the black lead to the negative terminal. 2. If the voltage level is less than 6.1 VDC, charge the battery. Rechargi N the Batt÷W Back-Up The CommerciaF Series U916 and R916 bikes are both self-powered (cordless)with Typically, the bike can be operated without Nugging in the battery charger. a rechargeable batteW back-up.
Nautilus E916 Elliptical Upon receiving your machine, use a soft, clean towel to wipe off the dust, which may have accumulated during shippingo Your new machine will require, minor assembly. Refer te theqnstaLlation Instructions" section for details. Cleaning = DO NOT USE GLASS CLEANERS ORANY OTHER HOUSEHOLD CLEANERS ON THE CONSOLE. Clean the console daily with a water-dampened c_oth and wipe dry after cbaning. 2.
th® Bal:1e y Backo J l} The Cemmercia_ Series EV918 arid E916 e4@tica_ are both self=powered (cordless) with a rechargeable battery back=up. Typica!ly, the elliptical can be operated without #lugging in the battery charger. If, however, the console flickers during operation or the console dis#lay does not _ight up whi_e using the machine, then use the battery charger to recharge the battery back-up. The battery charger is supplied with the unit and plugs into a standard 115volt, 15 amp outlet.
Nautilus Strength 1. UPHOLSTERV CLERI',IINGRHD PROTE_iOH A. Keep pads B. Clean and free of perspiration disinfect da)_ especially C. Clean areas all outside chlorinated Dish-ffectant at all times. upholstery where at the end [. e_oplrat_on surfaces with of each and scalp non-abrasive, household cleaners.. Cleaner is an effective non- Nautilus upholstery care 2. CLENNiNG NND CRREOF PRINTED $UflFNCES A. Wipe painted surfaces with a clotl_ and car wax. damp B. Let dry cloth.
Stairmaster £outine ClubTrack Maintenance 2100 Series Treadmills Schedules Performing reutine maintenance will help prevent unnecessaw wear to the treadmill and!or injuw to the user. The maintenance schedules are meant only to seP_eas a guide_Depending on where and how the treadmill is being used, more frequent routine maintenance may be required Daily • Inspect the powe_cord and walking belt for wear.
Treadmill Interior DANGEROUS VOLTAGES ARE PRESENT UNDER THE TREADMILL HOOD. EXERCUSECAUTION WHEN PERFORMING SERVICETO THE ELECTRICAL COMPONENTS UNDER THE HOOD. Depending upon the treadmill environment, dust and or lint c:snaccumulate under the hood Cleall the interior of the treadnlill following the procedure below: 1 Turn the t_eadmill circL_itbreaker off, and unplug the treadmill power cord,. Remove tile six (6) screws on the treadmill hoed. 3 Lifteffthe hood. 4 Clean i_/sidethe unit.
A_ustiH% I÷It T÷nsion SECIIE LONG HAIRAND LOOSE CLOTHINGIEIFOIE WOIRING HEAl THE TIEAI MILLWALKING S!tFACE 01 Pl LLEYS. DO NOT USE ALLYOUI WEIGHTTU IESIST THE BELT MOVEMEIT. TII llIl IE$1STAICE APPIIEI TOI LllI (MIIE TIAN IJl SEIOIIS) MAY SlUT IIWN TIE SYSTEM. (VAIIIUI Ellll MISSILES Will APPEAl iF TtLS U¢CUIS. CYCLEPOWEt TO RESUME NOtMAL OPERATION.) DO NOT UVEITIIHTEI TIE WALKING IELT. DO IUT TOIIUE AIJUSTMENT $CIEWS BEYIII I II-LIS 11 I-M)IA×IMUM.
Adiust the belt tension whenever the bett slips or moves unsteadily during operation by following the step,s below: 1 Start by loosening the two (2} adjustment bolts, Adjustment Bolts With the walking belt loose, place two marks 35 inches (:889ram) apaR on each side d the belt near the edge, The belt must be loose enough for you to move it from side to side on the front ,orrear roller.
A usting Be t Trackin@ Performthis:procedurewhenever the belt movesto one side or the other.
Stairmaster 7000PT Stepmill HELPFUL HINTS Readall maintenan£e[nstructbnstholo%hl_ybeforebeginningwork. [nsome case< an assistant is requiredW performthe necessau tasks,The safety level given by the designd this equipmentcan only be maintainedwhen ttle equipment is regularlyexaminedfor damageandwear.
Clean tile stq) hinges carefully. Perspiration tends to accumulate in the hinges and this can I@d to eventual corrosion, 6.
TheStairMaster_ StepmiIP 7000PTexerciseSYstemhas six componentsthat requireperiodiclubrication: the drive chain°the two step chains°the b_',/o bearing platesandthe step hinges.Thes4e parts are shown in the figure bebw. Youwill needto removethe side coversto lubricatethe chainsand the bearingplates, Dr_ve 1. Placea protectivemat on the floor wt]i]e you are lubricatingyour ' c machine.
. Cleaneachbearingplate and lubricate it with multipurposegreaseevery three months.Theplate is lubricatedto reducefriction when the ot4 stlaRbearingsroll over the plate, Onceper mo,_lth,use 3G _/motoroil or brushlight bear nggrease into the step hJnge:to lubricatethe hingesandto preventcorrosion.
Table 3.
Stairmaster 4600CL / 4600PT / 4200PT PREVENTIVEMAINTENANCE Most of these preventive maintenance procedure:scan be performed after removing the mid-cover:The preventive maintenance schedule is summarized in Table 3. The schedule is based on normal u_ge in a commercial health club environment; adjust the schedule to meet actual machine usage.
Lubrication There are nine componentsthat need periodic lubrication: the drive chain, the step chains, the pedal arm return springs, the step chain connection points, the pedal arm bushings,the leveling arm bushings,the spring pulley shafts, the pedal shafts and the leveling arm pins. These pars are shown in Figure 11, page 74. Removethe bottom cover to get to the components.
TO REDUCE THE POSSIBILITY OF SLIPPING, BE SURE THE PEDAL AREA IS FREEOF GREASE OR OIL, WIPE ANY EXCESS OIL OFF THE MACHINE SURFACES. Remove the spring pulleys every three months, Clean the spring pulley shafts with a dry cloth, Protect the shafts from corrosion with a thin coat of: multi-purpose 8_ grease before reassembling. Removethe tmdals every three months.
Table 3: Recommended Preventive Maintenance Schedule FRE@JEN_ W_:_ Daily CO|!sol÷ Dai!_y Lubrimte ;_i_ and d-_ms StepC ' o Cleanar_ lubricate St@ Cllain Connection PoiIT_ Spring Pulley Shafts Pe@l Shafts and Le,_qing _m Pins C_ANER MOlltJ]ly or aR_ 30) Iqo|Jrsof use QJa_e:lyor Dilu't_ b3usa_old clearer _A _%Wmotor oil Mild h_urs E_p/3 Cleanand lubricate _A malths Mu:lti.
Figure 11: Pa_s Needing Periodic Maintenance DriveC_in S_p C_in Leveli_ ArmPin PedalS_ I_veling Arm Shaft Ped=lArm _elj_ Fed_lArmS_ Arm B_hi_
Stairmaster 3800 Bike PREVENTIVEMAINTENANCE The procedures for performing recommended preventive maintenance on the Momentum systems r_/cle ergometer are summarized in Table 5, DO NOT USEG_SS CLEANEROR ANY OTHERHOUSEHOLD CLEANERSON THECONSOLE.Clean the console daily with a waterdampened cloth and wipe dry a_er cleaning, Clean the exterior covers, the pedals, and the seat on a weekly basis using either soap and water or a diluted, non-mineral based househoH cleaner such as Fantastic®.
Monthly Inspection Pedal crank: Inspectthe crank bearingsfor either excessiveplay or tightness, Either condition will reducethe Fifeof the bearings. Ensure the bearing damps are tighL Referto the "Part Removaland RepLacement"section of this manual for the proper adjustment Belts: inspect the HTDand PoJy-Vbelt for excessivewear, Adjust the belt tension if necessary. HTDBelt: Adjust the HTDbelt tension to allow 1/2" of belt deflection with fingertip pressure betw_n tile idler pulley and the HTDsprocket.
To adjust the tension: • bosen the idler • o o assemblyscrew sothat the idler pulley can slide up and down, Slidethe idler pulley up or down to tighten or loosenthe belt, Main flame Idlerassy Oncein position, tighten the idler assemblyscrew. Verifythe HTDlmlt tension. Poly-V belt: Make sum the belt is centered on the pulleys, To adjust the tension: • Loosen the top alternator attachment screw and the alternator adjustment nut. Pivot the alternator up or down as necessary to allow .25" (0.
Maintenance Table 5.
Stairmaster ClubStride 5100NSL Elliptical .... Upon receivin_ your machine, use a soft, clean towel to wipe off the dust, which may have accumulated during shipping. Your new machir_e will require minor assembly. Refer te the"lnstallation [nstructions" section for details. Cleaning = DO NOT USE GLASS CLEANERS ORANY OTHER HOUSEHOLD CLEANERS ON THE CONSOLE. Clean the conso4e daily with a water-dampened c_oth and wipe dry after cleaning. 2.
Schwinn Windrigger Use a damp of sweat, cloth Windrigger IMPORTANT: To avoid damaging Windrigger solvent to wipe your rower when the computer.
Schwinn IC Spinning Bikes II Dai|y maintenance Dry the Schwtnn Evolution remove Bike a_er each use to sweat and molsSure_ Wlpe your SchwJnn Evolution Bike regularly with a mlld_ non°abrasive cWeaner and water so[u_on_ Rinse to remove detergent residue and then dry [MPOEANT! To avoid damaging Schwlnn ba_d | Evolution the finish on your Bike, never use a _troleum o solvent when cleaning, Chain adjustme_ The chain on your _hwlnn fa_or¥ Evo[udon set and lubrlcatedo It should Immediate a_
Nautilus Stairmaster SM916 Stepmill Maintenance Maintenance Records For ease of maintenance the StepMill ':_SM916 console w[[[ keep track of hours, number of workouts, 5me between _ast servicing, etc, You can access any of the custom menus Iby pressing [LEVEE UP], [4], [ENTER]. The censure wi[[ men display MACH[NE STATUS, the opt:ions.
Maintenance Clean the exterior of the machine daily using soap and water or a diluted, non = mineral based householld cleaner such as Fantas5_ _:'. 2_ Maintenance Sched._e Oaily Weekly Monthly Co|_m ellis Ge.eraJ Maintenance Check Safety & Warnir_g Labels X Spot Check Step Chains X AlternatorBelt:Tension X Tension to 40-54 i:nlbs Lubric_ien Drive Chains 300 hrs.
iMPORTANT: If installing the optional LCDMonitor; refer to the NV915 installation manual at this time. The console will power on and remain powered whenever the external power supply is connected. Recycling Do not dispose of this product as refuse. This product is to be recycled. For informatio n on the proper method of disposal contact a Nautilus _' Customer Service Representative.
Nautilus Stairmaster SC916 Stairclimber Maintenance Maintenance Records For ease ef maintenance the SC918 Stairg[[mber console w'[H keep track of: hours, number of workouts, time be_een rust servicing, etc. You can quickly access any of the custom menus by pressing ]LEVEE UP], [4], [ENTER]. The console wi[_ then display "MACHINE STATUS." Use the [Level: UP] and [Leve_: DOWN] keys to scroll through the options° For detaills, refer to the Machine Status Console Codes [n the previous sec_on.
Maintenance Schedule General Maintenance X X X Tension to 3045 inlbs 30W OiI 300 hi's, Multi-Purpose glgase Or e_®p/ 900 his CleanLo,_r SideCovers X Clean with a water dampened cloth and wipe dry after cleaning, x soap a diluted household cleaner, X Sp,fiags ............. M Iti-Purpo se g_ ase or Clean, then wipe with lightly oil; soaked rag, C|eaning 11. Do not use glass cleaners or any other househoW cleaners on the consoJe.
Maintenance Checking the Baffery Charge 1. Using your mu_timeter, touch the red lead to the positive terminaJ a diluted, non°rain of the battew and the black lead to the negaUve terminal 2. If me vo_tage leve_ is less than 6.1 VDC, charge the ba_ewo Charging the Battery Back=Up The StairMasteP _ Commercial Series SC916 StairgJimber is selfpowered (cordless} with a rechargeaNe baEew bacbup.
