Schwinn® IC Bikes Evolution®, Evolution® SR Assembly Manual Nautilus® Bowflex® Schwinn® Fitness Pearl Izumi® StairMaster® Universal® Nautilus Institute® PN001-7189 (12/11/2007)
Table of Contents Product Specifications 2 Safety Warnings 3 Exploded Drawing 4 Parts List 5 Assembly Steps 6 Contact Numbers 11 Product Specifications Dimensions 50” L x 22.5” W x 40” H (127cm x 57cm x 102cm) Assembled Unit Weight 121 lbs (55 kg) Packaged Shipping weight 130 lbs (59 kg) Workout Area 89” L x 61.
Safety Warnings This icon means a potentially hazardous situation which, if not avoided, could result in death or serious injury. Before using this equipment, obey the following warnings: Read and understand the complete Owner’s Manual. Read and understand all Warnings on this machine. • Keep children away from this machine. Watch them closely when near the machine. Moving parts that appear dangerous to adults may not appear so to children. • Consult a physician before starting an exercise program.
Exploded Drawing 27 25 1 44 42 39 50 B 42 50 39 50 A 51 50 51 4 Assembly Manual 67
Parts List Ref. # 1 25 27 A B 67 Description Frame Handle Bar Seat Slider Assembly with Saddle Front Stabilizer Bar with Wheels and Feet Rear Stabilizer Bar with Feet Water Bottle Cage Small Parts Box Qty.
Assembly Step 1 Ref. # Description Qty 1 Frame 1 A Front Stabilizer Bar with Wheels and Feet 1 B Rear Stabilizer Bar with Feet 1 39 13mm Hex Bolt 4 50 Flat Washer 8 51 13mm Lock Nut 4 Tools Required Stamped Steel Combination Wrench 1 Adjustable wrench or 13mm Socket 1 5mm Hex Tool 1 Front A. Position the Front Stabilizer Bar (A) under the frame bracket as shown in the illustration. 39 B.
Assembly Step 2 Ref. # Description Qty 1 Frame 1 44 Pop Pin Assembly for Head Tube 1 25 Handle Bar 1 44, 27, 45 Seat Slider Assembly (Pre-Assembled) 26 Seat Post 67 Water Bottle Cage 1 2 Tools Required Adjustable wrench 1 A. Remove the Pop Pin Assembly (44) from the small parts bag and add some grease to the threads of the large 21mm nut that will screw into the head tube boss on the bike.
Assembly Step 3 Ref. # Description Qty 1 Frame 1 43 Pedals with Toe Clips & Straps (Left & Right) 1 Pair Tools Required Stamped Steel Combination Wrench 1 A. Remove Pedals (42) from the small parts box and look at the ends of the pedal threads. You will notice that each pedal is market with an “R” or an “L” on the very end of the spindle past the threads. This mark indicates which side of the bike the pedal is intended to mount.
Assembly/Initial Setup Adjustments Step 4 - Final Inspection A. Tighten all hardware. B. Read warnings on machine. Please read and refer to the Owner’s Manual for: • Operating Instructions • Maintenance Instructions • Warranty Information. Failure to visually check and test assembly before use can cause damage to the equipment. It can also cause serious injury to users and bystanders.
Assembly This page intentionally left blank.
Contact Numbers OFFICES IN THE UNITED STATES: INTERNATIONAL OFFICES: E-mail: customerservice@nautilus.com For technical assistance and a list of distributors in your area, please call or fax one of the following numbers. TECHNICAL/CUSTOMER SERVICE Phone: 800-NAUTILUS (800-628-8458) Fax: (877) 686-6466 E-mail: cstech@nautilus.com INTERNATIONAL CUSTOMER SERVICE Nautilus International S.A.
©2007. Nautilus, Inc. All rights reserved. Nautilus, the Nautilus Logo, Universal, Bowflex, StairMaster, Pearl Izumi and Nautilus Institute are either registered trademarks or trademarks of Nautilus, Inc. Schwinn and the Schwinn Quality Seal are registered trademarks. All other trademarks are owned by their respective companies. Nautilus, Inc., World Headquarters, 16400 SE Nautilus Drive, Vancouver, WA 98683 1-800-NAUTILUS www.nautilus.
