OWNER’S MANUAL Model 600A For 6 and 12-Volt Batteries TM computer smart amp amp ™ S L O W CHARGE MEDIUM CHARGE amp MEDIUM CHARGE Fully Automatic Microprocessor Controlled Battery Charger CAUTION: Read all Safety Rules and Operating Instructions, and follow them with each use of this product. Schumacher Electric Corporation Mount Prospect, IL 60056 U.S.A. Send Warranty Product Repairs to: Customer Service Returns P.O. Box 280,1025 E.
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ..................................................................... 3 PERSONAL SAFETY PRECAUTIONS ....................................................................... 4 BEFORE USING YOUR BATTERY CHARGER .......................................................... 5 PLUGGING IT IN.................................................................................................... 5 USING AN EXTENSION CORD.......................................................
Important Safety Instructions WARNING – RISK OF EXPLOSIVE GASES WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE THAT EACH TIME BEFORE USING YOUR CHARGER, YOU READ THIS MANUAL AND FOLLOW THE INSTRUCTIONS EXACTLY.
Never place charger directly above battery being charged. The gases from the battery will corrode and damage the charger. Be sure to position the charger power cord to prevent it from being stepped on, tripped over or damaged. Never pull out the plug by the cord when unplugging the charger. Pulling on the cord may cause damage to the cord or the plug. Never touch the battery clamps together when the charger is on. You could cause a spark.
BEFORE USING YOUR BATTERY CHARGER It is important to understand the charger’s requirements. This section explains the charger’s electrical requirements and how to prepare a battery for charging. PLUGGING IT IN Your charger requires a 120V AC receptacle installed according to all local codes and ordinances. • Make sure that pins on plug of extension cord are the same number, size, and shape as those of plug on charger. • Check that the extension cord is properly wired and in good electrical condition.
operating instructions IMPORTANT: Follow all safety instructions and precautions when charging your battery. Wear complete eye protection and clothing protection. Charge your battery in a well-ventilated area. Charging Battery In The Vehicle: part of the chassis or engine block, away from the battery (see figure above). DO NOT connect clamp to negative battery post, carburetor, fuel line or sheet metal part. 1. Avoid personal injury by keeping clear of fan blades, belts, pulleys and other engine parts.
Charging Battery Removed From The Vehicle: POSITIVE 6. Press the appropriate control buttons to select the desired charge rate and battery voltage. The CHARGING (yellow) LED should light and the charging process should start. If the CONNECTED (red) LED is not on, check for correct cable connections. NEGATIVE BATTERY CHARGER BATTERY 24", 6 GAUGE CABLE 7. To disconnect the charger, unplug its power cord before attempting to disconnect the charger clamps.
speedcharge CONTROL TM CHARGED 75% 50% 2A SMALL 6V 4A MEDIUM 12V 25% 6A LARGE CHARGING CONNECTED BATTERY SIZE BATTERY TYPE 600A CONTROL PANEL BATTERY SIZE Use this button to set the charge rate to one of the following three: BATTERY TYPE BUTTON Use this switch button to set the type of battery to be charged to one of the following two: • 2A or 4A BATTERY SIZE: Intended for charging small batteries such as those commonly used in garden tractors, snow mobiles and motorcycles.
using your battery charger OVERVIEW Using the battery charger is very simple. First, connect the battery and AC power following the precautions listed under “OPERATING INSTRUCTIONS”. Then select the appropriate BATTERY TYPE and BATTERY SIZE for your battery. The charger will then do everything automatically. This section explains a few details. AUTOMATIC SHUT OFF: When the 2A, 4A or 6A charge rate is selected, the charger is set to perform an automatic charge.
charging tips Read this entire manual before using your charger. The tips below serve only as a guide for specific situations. Reviving your battery: If you only wish to charge your battery enough to start your vehicle, you do not need to wait for the entire charging process to be completed. When the battery status displays 3 yellow LEDs the battery has usually been charged enough for the vehicle to start normally.
Troubleshooting Performance problems often can be corrected by the user. Please completely read this chart for possible solutions to common problems. PROBLEM POSSIBLE CAUSE Connected light is not on. The battery is not connected Connect or adjust clips. correctly. Check for correct polarity. SOLUTION Connected to 12 volt battery, Press the button to select 6V selected on charger. the correct size and type. Connection to battery is reversed. Correct connection. The battery is less than one volt.
limited warranty SCHUMACHER ELECTRIC CORPORATION, 801 BUSINESS CENTER DRIVE, MOUNT PROSPECT, ILLINOIS 60056-2179 MAKES THIS LIMITED WARRANTY TO THE ORIGINAL PURCHASER AT RETAIL OF THIS PRODUCT. THIS LIMITED WARRANTY IS NOT TRANSFERABLE. Schumacher Electric Corporation warrants this battery charger for five years from date of purchase at retail against defective material or workmanship. If such should occur, the unit will be repaired or replaced at the option of the manufacturer.
MANUAL DEL DUEÑO Modelo 600A Para Baterías de 6 y 12 voltios TM computer smart ™ 2 4 amperios C A R G A L E N T A 6 amperios C A R G A MEDIANA amperios C A R G A MEDIANA Cargador de Baterías Totalmente Automático Controlado por Microprocesador PRECAUCIÓN: Lea todas las Reglas de Seguridad e Instrucciones de Operación y sígalas en cada uso de este producto. Schumacher Electric Corporation Mount Prospect, IL 60056 U.S.A. Envíe los productos para Reparación bajo Garantía a: Customer Service Returns P.
ÍNDICE INSTRUCCIONES IMPORTANTES DE SEGURIDAD ................................................ 3 PRECAUCIONES DE SEGURIDAD PERSONAL ....................................................... 4 ANTES DE USAR SU CARGADOR DE BATERÍAS . ................................................. 5 CÓMO ENCHUFARLO........................................................................................... 5 EL USO DE UN CORDÓN DE EXTENSIÓN.........................................................
Instrucciones de Seguridad Importantes ADVERTENCIA – RIESGO DE GASES EXPLOSIVOS EL TRABAJAR PRÓXIMO A UNA BATERÍA DE PLOMO-ÁCIDO ES PELIGROSO. LAS BATERÍAS GENERAN GASES EXPLOSIVOS DURANTE SU OPERACIÓN NORMAL POR ESTE MOTIVO, ES DE SUMA IMPORTANCIA QUE CADA VEZ, ANTES DE USAR SU CARGADOR, USTED LEA ESTE MANUAL Y SIGA LAS INSTRUCCIONES EXACTAMENTE.
Si el fluido de la batería (electrolito) se congela, lleve la batería adentro de un sitio abrigado y permita que la batería se descongele antes de comenzar a cargarla. Nunca opere el cargador de baterías si ha recibido golpe fuerte, se ha dejado caer o de otro modo ha sufrido daño. Llévelo a un profesional calificado para inspección y reparación. Nunca deje que el ácido de la batería caiga sobre el cargador mientras usted lee la gravedad específica o llene la batería.
ANTES DE USAR SU CARGADOR DE BATERÍAS Es importante entender los requisitos del cargador. Esta sección explica los requisitos eléctricos del cargador y la manera de preparar una batería para cargarse. • Asegúrese que todas las clavijas en el enchufe del cordón de extensión sean del mismo número, tamaño y forma que aquellos del enchufe en el cargador. • Verifique que el cordón de extensión esté correctamente cableado y en buenas condiciones eléctricas.
INSTRUCCIONES DE OPERACIÓN IMPORTANTE: Siga todas las instrucciones y precauciones de seguridad al cargar la batería. Lleve protección completa para los ojos y para la ropa. Cargue la batería en un área bien ventilada. PARA CARGAR LA BATERÍA DENTRO DEL VEHÍCULO la figura arriba). NO conecte la pinza al poste negativo de la batería, ni al carburador, la línea de combustible o ninguna plancha de metal. 1.
PARA CARGAR LA BATERÍA SACADA DEL VEHÍCULO: POSITIVO NEGATIVO CARGADOR DE BATERÍAS BATERÍA CABLE DE 24”, CALIBRE 6 CORDÓN DE FUERZA AL TOMACORRIENTE DE FUERZA A TIERRA 1. Note la polaridad de los postes de la batería al verificar las marcaciones de identificación en la batería: POSITIVO (POS, P o +) y NEGATIVO (NEG, N o -). El poste positivo generalmente es más grande que el poste negativo. 6. Oprima los botones de control apropiados para seleccionar la tasa de carga y el voltaje de batería deseadas.
CONTROLES DEL SPEEDCHARGE TM CARGADA 75% 50% 2 AMP PEQUEÑA 6 VOLTIOS 4 AMP MEDIANA 12 VOLTIOS 25% 6 AMP GRANDE CARGANDO CONNECTADA TAMAÑO DE BATERÍA TIPO DE BATERÍA PANEL DE CONTROL DEL 600A BOTÓN DE TIPO DE BATERÍA (Battery Type) Use este conmutador para fijar el tipo de batería a ser cargada en uno de los dos tipos a continuación: BOTÓN DE TAMAÑO DE BATERÍA (Battery Size) Use este botón para fijar la tasa de carga en una de las tres a continuación: • TASA DE CARGA 2A o 4A: Destinada para cargar
CÓMO USAR SU CARGADOR DE BATERÍAS CIERRE AUTOMÁTICO: Cuando se selecciona la tasa de carga 2A, 4A o 6A, el cargador queda preparado para efectuar carga automática. Al efectuar carga automática, el cargador deja automáticamente de cargar después de que la batería esté cargada. VISTA GENERAL El modo de usar el cargador de baterías es muy sencillo. Primero, conecte la batería y la potencia CA siguiendo las precauciones detalladas bajo ‘INSTRUCCIONES DE OPERACIÓN”.
PAUTAS PARA CARGAR Lea este manual entero antes de usar el cargador. Las pautas a continuación sirven únicamente de guía para situaciones específicas. Para restaurar la batería. Si se desea cargar la batería sólo lo necesario para que el vehículo arranque, no se necesita esperar que se complete el ciclo entero de cargar. Cuando el estado de la batería muestra 3 de los DEL en amarillo, la batería por lo general ha sido cargada lo suficiente para que el vehículo arranque en forma normal.
SOLUCIÓN DE PROBLEMAS A menudo el usuario mismo puede corregir los problemas de funcionamiento. Sírvase leer este cuadro de principio a fin para encontrar posibles soluciones a los problemas comunes. PROBLEMA POSIBLE CAUSA SOLUCIÓN La luz CONNECTED no se enciente. La batería no está conectada correctamente. Conecte o ajuste las pinzas. Verifique que la polaridad sea correcta. Conectado a batería de 12 voltios, pero se ha seleccionado 6V en el cargador.
PROBLEMA POSIBLE CAUSA SOLUCIÓN El cargador está haciendo un ruido de chasquido audible. El cargador tiene un relé que enciende y apaga la corriente a la batería. No hay problema, es condición normal. La corriente medida es mucho más baja que aquella seleccionada. El cargador llegó al voltaje máximo y está reduciendo la corriente. No hay problema, es condición normal.