JERSEY Purchase date : _________________ Product Tracking Reference : _____________________________ Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-866-839-2888, 9 a.m. – 5 p.m., EST, Monday – Friday.
TABLE OF CONTENTS Package Contents........................................................................................................................................3 Hardware Contents......................................................................................................................................5 Safety Information........................................................................................................................................6 Preparation....................
PACKAGE CONTENTS P F N O M F Q C D E S R I L G M K A J H B 3 L
PACKAGE CONTENTS PART DESCRIPTION QUANTITY CODE A Base 1 --- B Base flange 2 --- C Fixed glass panel 1 99SG10315-WM D Shower door 1 99SGD0014-WM E Side panel 1 99SG20012-WM F Aluminum metal track 2 99STR0025-WM G Vertical rubber track 1 99SRU0006 H PVC magnetic door seal 2 99SRU0021 I Rubber strip (Long) 1 99SRU0033 J Bottom rubber track 1 99SRU0009 K Rubber strip (Short) 1 99SRU0003 L Glass support bracket 2 99SGC0012-WM M Shower hinge 2 99SHI0011-WM
HARDWARE CONTENTS BB CC Wall plug ø6X30 Screw ST4X30 Screw ST4X15 Brass cap & fitting Screw ST4X20 Qty. 8 Qty. 8 Qty. 6 Qty. 6 Qty. 2 AA HH II DD JJ EE KK LL Screw ST5X35 Wall plug ø8X30 Allen key 2.5 mm Allen key 4 mm Large cap Qty. 2 Qty. 2 Qty. 1 Qty. 1 Qty. 4 MM Small cap Qty.
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. • Handle the tempered glass with caution! Improperly handling the glass can cause it to break suddenly in small pieces (never in pointed fragments). • You will need at least two people to install this unit properly. WARNING • OVE is not responsible for any damage to the unit or personal property caused by improper installation.
INSTALLATION INSTRUCTIONS STEP A The center of one metal track should be 30 1/2 in. (775 mm ) from the wall. And the center of another metal track should be 58 1/2 in. (1486 mm) from the wall. The two metal tracks should be placed at approximately 1 1/4 in. (30 mm) from the edge of the base to the track center. n. /2 i mm ) 58 1 1/4 in. (30 mm) 1 30 5 (77 7 1/2 in.
INSTALLATION INSTRUCTIONS STEP B It is recommended that a small diameter bit be used when first drilling ceramic tiles to avoid breaking them. Begin with the smaller bit and gradually move to larger drill bits until the proper sized hole is attained. 1. Level the tracks (F) and mark the track holes positions. Temporary removes the frames and ensures that the distance is correct. 2. Drill pilot holes at the marked place. Ensure that the final hole is large enough to fit snugly the wall anchors. 3.
INSTALLATION INSTRUCTIONS STEP C 1. Place the seal strips (I) at the base of glass panels (C & E) and cut it to size. 2. Place the seal strips (K) at the base of the glass (E) and cut it to size. 3. Insert glass panels (C & E) into the tracks (F). Do not fully tighten hardware as further adjustments may be required.
INSTALLATION INSTRUCTIONS STEP D 1. Using an Allen key (JJ), install the hinges (M) on the glass panel (C) by following the illustration. Install shower door (D) to the hinges that are on the glass panel. 2. Install the bottom rubber track (J) on the shower door (D) and cut it to size. The longer lip of the strip must be in the internal side of the shower. 3. Install the PVC magnetic door seals (H) on the edge of shower door and side panel. 4.
INSTALLATION INSTRUCTIONS STEP E 1. Using a cutter, remove exposed rubber strips where the glass support brackets (L) are to be installed. 2. Place rear part of bracket (L) and one rubber gasket (FF) centered in the notch as illustrated and mark location of hole to drill on shower base. Remove glass support bracket (L) and rubber gasket (FF). Drill a hole in the shower base using the drill. 3.
INSTALLATION INSTRUCTIONS STEP F 1 & 2. Inset the glass clips (O & Q) and wall brackets (P) on the support bar (N). 3. Place the support bar on the glass panels (C & E), then adjust the glass clips position on the support bar. 4. Mark the wall bracket (P) positions on the wall. 5 & 6. Temporarily remove the support bar from the glass panel. 7. Place the wall bracket (P) on the marked line on the wall, mark the two holes position of the bracket plate. 8. Drill the two holes on the marked place. 9.
INSTALLATION INSTRUCTIONS STEP G 1. Disassemble the handle (R & S) using an Allen key. Install the handle (R & S) as shown. 2. Ensure that the door closes tight and opens smoothly, and there is a tight connection between the side glass panel and the frame as well as the support bar. 3.
CARE AND MAINTENANCE For the daily maintenance, use a wet cloth and a soft liquid cleaner. Never use abrasive cleaners containing some acetone, chlorine or strong bleach, scrapers, metallic brushes, nor other objects or the products which can graze or tarnish surfaces. LIMITED 5-YEAR WARRANTY This warranty extends only to the original owner lend-user for personal household use only. For commercial uses, additional limitations may apply. Distributor warrants your satisfaction with each shower.
