Installation Manual

2
Copyright © 2014-15 Schneider Electric. All Rights Reserved.
All trademarks are owned by Schneider Electric Industries SAS or its affiliated companies.
solar.schneider-electric.com
Conext™ Mini Power Distribution Panel Installation Guide
865-1013-01
D
Knockout and Product Dimensions
F
Wall Mounting the Mini PDP
AC1
AC2
Event
Equalize
kW
A
Charging
!
Inverting
Refer to the Conext XW/XW+
Inverter/Charger Installation Guide for
detailed mounting instructions.
Wall mount the Conext XW/XW+.
Before mounting the Mini PDP, mount the Conext XW/XW+ to the wall first.
1
NOTE: When remov-
ing your choice of
knockouts, ensure no
debris remains inside
the chassis. Insert
appropriately-sized
UL/CSA strain reliefs.
EQUIPMENT DAMAGE
Do not drill, cut or punch holes into the XW/XW+ chassis or Mini PDP. Use only the
knockouts provided for conduit entry.
Failure to follow these instructions can result in damage to equipment.
NOTICE
Inner: 3/4" trade (28.2 mm or PG 21)
Outer: 1" trade (35 mm)
Inner: ISO-16
Outer: 1/2" trade (22.2 mm or PG 16)
Inner: ISO-40
Outer: ISO-50
Inner: 1 1/2" trade
Outer: 2" trade (62.7 mm)
outside view
Bottom Knockouts
3x
2x
2x
1x
Side Knockouts
(L) outside view (R)
Inner: 3/4" trade (28.2 mm or PG 21)
Outer: 1" trade (35 mm)
6x
Inner: 1/2" trade (22.2 mm or PG 16)
Outer: 3/4" trade (28.2 mm or PG 21)
2x
3/4" trade (28.2 mm or PG 21)
Holes for mounting
Conext MPPT 60 150
solar charge controllers
2x
Loosen the 2 attachment screws
(included) on the bottom of the
XW/XW+ unit.
Remove the DC terminal
flat and split washers and
bolts (included with the
XW/XW+ unit).
Loosen the attachment screws and remove the DC terminal bolts and washers
on the XW/XW+.
E
Removing the Mini PDP Door and Faceplate
Optional: To mount the door on the other
side of the Mini PDP, remove the top and
bottom screws holding the brackets in
place and reattach on the opposite side.
Remove and reverse the two brackets on
the top and bottom of the door assembly.
Reposition the magnetic latch.
Remove the top (shown)
and bottom screws holding
the door brackets in place
Remove the door,
if desired.
1
To access the wiring and breakers, open the door, remove the front
faceplate (as shown) on the Mini PDP.
Set aside the 8 screws.
Attach the Mini PDP to the XW/XW+.
AC1
AC2
Event
Equalize
kW
A
Charging
!
Inverting
Align the keyholes on the top of the Mini PDP and push it
up flush against the bottom of the XW/XW+.
Tighten the attachment
screws (2x) to the
XW/XW+. Torque screws
to 12 in-lbf.
NOTE: Detach the front
breaker assembly if
necessary to ease
securing the attachment
screws to the XW/XW+.
Secure the bottom mounting
bracket with 4 wall screws
(not provided)
XW+ unit
(shown - not included)
407 mm
(16 ")
632 mm
(24.9")
DOOR SWING
CLEARANCE
430 mm
(16.9")
470 mm
(18.5")
406 mm
(16")
209 mm
(8.2")
225 mm
(8.9")
Outside Dimensions