Manualshelf

User Manual

ManualsBrandsSchneider ManualsInverter AccessoriesSchneider Conext ComBox
1234
975-0643-01-01 C
7-2014
1
www.schneider-electric.com
Conext™ ComBox
865-1058
Contact Information
www.schneider-electric.com
Please contact your local Schneider Electric Sales Representative or visit the Schneider Electric website at:
http://www.schneider-electric.com/sites/corporate/en/support/operations/local-operations/local-operations.page
B Material List
A
B
C
D
E
F
G
H
Communication and
Monitoring Device
Quick Start Guide
HAZARD OF ELECTRIC SHOCK AND FIRE
Failure to follow these instructions will result in death or serious injury.
Connect only to Safety Extra Low Voltage (SELV) circuits and power sources.
All wiring must be done by qualified personnel to ensure compliance with all applicable installa-
tion codes and regulations.
For Indoor Use Only.
Do not disassemble. No user serviceable parts inside.
DANGER
Exclusion for Documentation
UNLESS SPECIFICALLY AGREED TO IN WRITING, SELLER
(A) MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY TECHNICAL OR OTHER INFORMATION PROVIDED IN ITS MANUALS OR OTHER
DOCUMENTATION;
(
B) ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSSES, DAMAGES, COSTS OR EXPENSES, WHETHER SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL OR INCIDENTAL, WHICH
MIGHT ARISE OUT OF THE USE OF SUCH INFORMATION. THE USE OF ANY SUCH INFORMATION WILL BE ENTIRELY AT THE USER’S RISK; AND
(C) REMINDS YOU THAT IF THIS MANUAL IS IN ANY LANGUAGE OTHER THAN ENGLISH, ALTHOUGH STEPS HAVE BEEN TAKEN TO MAINTAIN THE ACCURACY OF THE TRANSLATION,
THE ACCURACY CANNOT BE GUARANTEED. APPROVED CONTENT IS CONTAINED WITH THE ENGLISH LANGUAGE VERSION WHICH IS POSTED AT WWW.SCHNEIDER-ELECTRIC.COM.
Conventions Used
A
FED G H
C
C Identification
Reset pinhole
Micro-SD port
USB Host port
USB Device port
LED indicator lights
Power port
Xanbus ports
DIN rail sliding catch
RS 485 Modbus port (or RS 485 port)
10/100 Ethernet port
Dry contact port
A
B
C
D
E
F
G
H
I
J
K
A B C D
E
F
G
H
J KI
A Introduction
E1 Mounting to a wall
this mounting template is 1:1
4
7
/16" (112 mm)
1
/
4
"
(6 mm)
#6 screw (supplied)
mark on the wall
D Overview of available power sources
NOTE:
The Conext ComBox can be powered by all three sources simultaneously. Typically,
the AC/DC adapter is used as a primary power source. Xanbus or 24V input power
through the RS 485 are secondary power sources.
Do not turn on the Conext ComBox by connecting to either of these power sources
until section H1 Turning On the ComBox.
Xanbus
a
24V power
supply on RS 485
5.5 mm
2.1 mm
12V, 1.5A
a. For a complete list of Xanbus-enabled devices including devices that can provide power
to the Conext ComBox, see the Installation and Configuration Guide.
The Conext ComBox is a multi-function communication device that delivers system
performance monitoring for residential, industrial and telecom energy systems. As well as
being a datalogger, the ComBox provides a communications gateway between a network
of Xanbus™-enabled devices and Modbus devices through an RS485 or TCP/IP
connection. System operators can also remotely configure the ComBox and monitor
performance with third party software packages.
A
Section Step
A
Label
Safety
Direction
Expand
B
Conext ComBox unit
AC/DC adapter* with changeable plugs
Thumb Drive (User guides, device discovery tool)
Ethernet cable
Xanbus network terminator
RS 485 Modbus connector (or RS 485 connector)
Dry contact connector
Woodscrew #6 with anchor (2)
* When ordering a replacement, reference PN: 0J-921-0023-Z.

Summary of content (4 pages)