Automation & Control Advantys™ STB IP20 Distributed I/O Catalog October 07 This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123 www.barr-thorp.
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123 www.barr-thorp.
us. Flexibility Interchangeable modular functions, to better meet the requirements for extensions b Software and accessories common to multiple product families b This international site allows you to access all the Telemecanique® brand products in just 2 clicks via comprehensive range data-sheets, with direct links to: b Complete library: technical documents, catalogs, certificates, FAQs, brochures... b Selection guides from the e-catalog. b Product discovery sites and their Flash animations.
Contents 0 Advantys™ STB IP20 Distributed I/O Solution 1 Open and Modular System b Presentation, composition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pages 6 to 7 b Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pages 8 to 11 b Functions, characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pages 12 and 13 Network Interface Modules Selection guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuration Software b Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 82 b Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pages 83 to 86 b References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 87 Dimensions b Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Presentation Advantys™ STB Distributed I/O Solution Open and Modular System Presentation To meet the needs of machine manufacturers and users, automation architectures have been decentralized while delivering performance close to that of centralized systems. Installed as close to the machine as possible, these island architectures reduce the time and cost of wiring for sensors and actuators, while increasing system availability.
Composition Advantys™ STB Distributed I/O Solution 0 Open and Modular System Composition of an Advantys STB island An Advantys STB island is made up of one or more segments comprising PDMs (Power Distribution Modules) and input/output modules. An Advantys STB island starts with a network interface module and ends with a bus terminator supplied with this module.
Description Advantys™ STB Distributed I/O Solution 0 Open and Modular System Description of Advantys STB basic Advantys STB basic: single segment With a basic network interface module it is possible to realize an island with only one segment (a “single” segment) comprising up to 12 input/output modules (excluding PDM power distribution modules, network interface module and bus termination).
Description (continued) Advantys™ STB Distributed I/O Solution 0 Open and Modular System Standard Advantys STB configurations Standard Advantys STB: single segment With a standard NIM network interface module it is possible to realize an island with only one segment (a “single” segment) comprising up to 32 input/output modules (excluding PDM power distribution modules, network interface module, bus termination and auxiliary power supplies).
Description (continued) Advantys™ STB Distributed I/O Solution Open and Modular System Standard Advantys STB: primary segment and extension segments The island bus can support the primary segment with up to 6 extension segments (7 segments in all). A standard NIM network interface module supports up to 32 I/O modules (excluding PDM power distribution modules, network interface module, bus termination, auxiliary power supplies and EOS/BOS bus extension modules).
Description (continued) Advantys™ STB Distributed I/O Solution 0 Open and Modular System Standard Advantys STB: CANopen extension module - Device Integration The CANopen extension module STB XBE 2100 can be used to connect, at the end of the segment, external CANopen devices such as: v IP67 Advantys FTB I/O, in plastic or metal casing. v Altivar® 31/61r/71r variable speed drives. v Festo® CPV-CO2 electropneumatic valves. v Parker® P2M2HBVC11600 electropneumatic valves.
Advantys™ STB Distributed I/O Solution Functions Open and Modular System Basic/standard Advantys STB functions The table below sets out the main features of the basic and standard Advantys STB ranges: I/O modules Advantys STB Basic Max. no.
Advantys™ STB Distributed I/O Solution Characteristics 0 Open and Modular System Operating environment Advantys STB devices satisfy the following regulatory agency certifications: b UL b CSA b CE b FM Class 1, Div. 2 They are designed for use in industrial environments of pollution class 2, in applications of over voltage category II (as defined in publication IEC 60664-1) and at altitudes of up to 2000 m (2187.22 yd), without reduction in load.
Selection guide Advantys™ STB Distributed I/O Solution 0 Network Interface Modules Applications Data exchange between master PLC and Advantys STB I/O modules Bus or network type Ethernet TCP/IP Network CANopen bus Bus or network nature Industrial LAN CAN field bus Physical interface 10 BASE-T ISO 1198 Data rate 10 Mbit/s 10 Kbit/s…1 Mbit/s depending on bus length Shielded dual twisted pair via Ethernet ConneXium ™ cabling system Shielded dual twisted pair Number of devices (1) Up to 256
0 Data exchange between master PLC and Advantys STB I/O modules Modbus Plus™ network Fipio® bus Industrial LAN compliant with the Modbus Plus standard INTERBUS® bus Profibus DP bus DeviceNet network Open industrial field bus INTERBUS industrial field bus compliant with the FIP standard (Generation 4) Industrial field bus Profibus DPV.0 Modbus Plus standard FIP standard Isolated RS 485 RS 485 Network compliant with v.2.0 of the Open DeviceNet Vendor Assoc.
Advantys™ STB Distributed I/O Solution Presentation Network Interface Modules Presentation The STB Npp 2212 and STB Npp 1010 NIM (Network Interface Module), located at the beginning of each island, are gateways for exchanging data between the network or bus master PLC and the Advantys STB automation island. The standard modules STB Npp 2212 also allow configuration and addressing of the external devices of the installation. These settings are stored in the module’s internal RAM or Flash memory.
Presentation (continued) Advantys™ STB Distributed I/O Solution 0 Network Interface Modules The range of NIM network interface modules comprises 4 basic NIM modules and 7 standard NIM modules.
Advantys™ STB Distributed I/O Solution Description Network Interface Modules Description Network interface modules STB Npp 2212/1010 The front panel of the STB Npp 2212/1010 network interface module has the following features: 4 1 5 6 2 7 3 (STB Npp 2212 standard module only) 8 Interface modules with network/bus address selectors. 1 4 5 6 2 7 3 8 INTERBUS STB NIB 2212/1010 interface modules (STB Npp 2212 standard module only) 1 A connector to connect the island to the fieldbus.
Characteristics Advantys™ STB Distributed I/O Solution 0 Network Interface Modules Characteristics Type of network interface module Range Network or bus STB Compliance with bus or network standards Power supply Input current Voltage limits Output voltage to the island logic bus Output current rating Isolation Immunity to electromagnetic interference (EMC) Connector type Max. number of addressable I/O modules Number of segments supported cV mA cV c A NCO 2212 Standard CANopen IEEE 802.
Catalog numbers Advantys™ STB Distributed I/O Solution 0 Network Interface Modules Network interface modules (1) Network or bus Ethernet network Standard Power supply (2) c 24 V CANopen bus Standard c 24 V STBNCO2212 0.135 Basic c 24 V STBNCO1010 0.135 Modbus Plus™ network Standard c 24 V STBNMP2212 0.145 Fipio® bus Standard c 24 V STBNFP2212 0.145 INTERBUS® bus Standard c 24 V STBNIB2212 0.155 Basic c 24 V STBNIB1010 0.155 Standard c 24 V STBNDP2212 0.
Catalog numbers (continued) Advantys™ STB Distributed I/O Solution 0 Network Interface Modules Connection accessories CANopen bus Designation TSX CAN TDM4 Fitted at ends Length CANopen IP 20 junction box 4 SUB-D ports. Screw terminals for connection of main cables Line termination Pre assembled CANopen cables 1 SUB-D connector, 9-way, female at each end. Standard, e marking: low smoke emission. Halogen-free.
Catalog numbers (continued) Advantys™ STB Distributed I/O Solution 0 Network Interface Modules Connection accessories (continued) Modbus Plus™ network Designation Use Catalog number 9-pin SUB-D male connector Connection of the Modbus Plus connector ASMBKT085 Modbus Plus junction box IP 20 device for T connections 990NAD23000 0.230 IP 65 unit for T connections, supports 1 RJ45 connector on front panel 990NAD23010 0.
Catalog numbers (continued) Advantys™ STB Distributed I/O Solution 0 Network Interface Modules Connection accessories (continued) INTERBUS® Bus Designation Installation bus cables Junction interface Inter-station bus cables Use Length Pre assembled cables for 0.110 m connecting 2 network (0.12 yd) interface modules 1m (1.09 yd) To connect inter-station – bus to installation bus – 100 m (109.3 yd) 400 m (437.
Catalog numbers (continued) Advantys™ STB Distributed I/O Solution 0 Network Interface Modules Internal bus extensions Designation Use with standard STB Installed at end of segment STBXBE1000 (except for the last segment on the island) BOS internal bus extension module Installed at the beginning of STBXBE1200 each extension segment – Bus extension module to CANopen external devices Installed at the end of the last STBXBE2100 segment to connect standard CANopen devices – Auxiliary power supply c
Catalog numbers (continued) Connections Advantys™ STB Distributed I/O Solution 0 Network Interface Modules Bus extensions: Optional separate parts Designation Keying pin Used for Modules Removable connectors Customizing labels (1) I/O bases and modules Insulated Screw-type screwdriver removable 2.5 mm (0.
Presentation Advantys™ STB Distributed I/O Solution Power Distribution Modules Presentation The STB PDT p105 basic PDM (Power Distribution Modules) provide power for the I/O module sensors and actuators (1) via the same bus 3. Two basic power distribution modules are available: b The STB PDT 3105 module is dedicated to providing power to I/O module sensors and actuators requiring a c 24 V power supply.
Presentation (continued) Advantys™ STB Distributed I/O Solution 0 Power Distribution Modules Connection of power supplies (continued) A single power supply a 115/230 V a 115/230 V 3 3 IN/OUT IN/OUT c 24 V Configuration with basic PDM Low-cost configuration with a single power supply for the NIM network interface module, sensor bus and actuator bus.
Advantys™ STB Distributed I/O Solution Description 0 Power Distribution Modules Description 7 2 (STB PDT p100 standard module only) 1 3 4 5 6 8 (STB PDT p100 standard module only) The front panel of the Advantys STB PDT p10p power distribution modules features: 1 A location for a customized label.
Characteristics Advantys™ STB Distributed I/O Solution 0 Power distribution modules Characteristics of power distribution modules Type of module Range Power supply V Max. current STB PDT 3100 Standard c 24 (1) STB PDT 2100 a 115/230 STB PDT 2105 a 115/230 For inputs A 4 at 30°C (86°F) 5 at 30°C (86°F) – 2.5 at 60°C (140°F) 2.5 at 60°C (140°F) – For outputs A 8 at 30°C (86°F) 5 at 60°C (140°F) 10 at 30°C (86°F) 5 at 60°C (140°F) – – For inputs/outputs A – – 4 at 30°C (86°F) 2.
Characteristics (continued) Advantys™ STB Distributed I/O Solution Power distribution modules Characteristics of auxiliary and bus extension power supplies Type of module Auxiliary power supply: c 24 V/c 5 V EOS internal bus extension BOS internal bus extension Bus extension to external CANopen devices STB CPS 2111 c 24 Not isolated STB XBE 1000 – STB XBE 1200 c 24 Not isolated STB XBE 2100 – Power supply 2-pin removable – 2-pin removable – Interface – Firewire Firewire 5-pin removable
Advantys™ STB Distributed I/O Solution Catalog numbers 0 Power distribution modules Catalog numbers Power distribution modules Type of power supply c a Voltage Type Catalog number 24 V Standard STBPDT3100 Weight kg 0.130 Basic STBPDT3105 0.130 Standard STBPDT2100 0.129 Basic STBPDT2105 0.129 115/230 V Mandatory separate parts Designation STB XBA 2200 STB PDT 3100 Mounting base width 18.4 mm (0.
Selection guide Advantys™ STB Distributed I/O Solution Digital Input/Output Modules Applications Digital input modules Direct current Voltage c 24 V Number of channels 2 4 Sensor type 2 or 3-wire + ground 2 or 3-wire Default logic Configurable logic Type (IEC/EN 61131-2) Internal power supply for 3-wire sensors Positive Yes (1) Type 2 Yes (2 outputs) No Type 1+ Yes (4 outputs) Yes (1) Off-to-on 610 μs @ 0.2 ms input filter time 625 μs @ 0.2 ms input filter time 3.5 ms 925 μs @ 0.
0 Digital input modules Direct current c 24 V 6 16 2-wire 2 or 3-wire Positive No Type 1 No Yes (1) No Type 3 Yes (4 outputs) 5.25 ms 1.21 ms 2 ms 5.75 ms 1.
Selection guide (continued) Advantys™ STB Distributed I/O Solution Digital Input/Output Modules Applications Digital output modules For direct current (transistor) Voltage c 24 V Number of channels 2 4 Positive Yes Yes No No Yes 0.5 A Outputs Default logic Configurable logic Internal power supply for 3-wire actuators Load current Response time Off-to-on On-to-off 0.5 A 2A 0.25 A 620 μs @ 0.5 A load 575 μs @ 0.5 A load 520 μs 720 μs 560 μs @ 0.25 A load 560 μs @ 0.5 A load 870 μs @ 0.
Digital output modules For direct current (transistor) c 24 V 6 16 Positive No No Yes No No 0.25 A 0.5 A up to 0.5 per channel 550 μs @ 250 mA load 715 μs @ 0.5 A load 900 μs @ 250 mA load 955 μs @ 0.5 A load 2 ms @ 0.5 A load 2 ms @ 0.
Selection guide (continued) Advantys™ STB Distributed I/O Solution Digital Input/Output Modules Applications Digital input modules Alternating current Voltage a 115 V Number of channels 2 Sensor type 2 or 3-wire + ground Inputs Response time Default logic Configurable logic Type (IEC/EN 61131-2) – Yes (1) Type 1 Internal power supply for 3-wire sensors Yes Off-to-on On-to-off 1.5 line cycles 1.
Advantys™ STB Distributed I/O Solution 0 Digital Input/Output Modules Applications Digital output modules For direct/alternating current (relay) For alternating current (triac) Voltage c 24 V (relay contact) a 115/230 V (relay contact) a 115 V Number of channels 2 form C (N.O/N.
Presentation description Advantys™ STB Distributed I/O Solution Digital Input/Output Modules Presentation Advantys STB digital input/output modules consist of: b Input modules. b Static output modules. b Relay output modules. The range of basic digital I/O modules comprises : b 3 digital input modules: v 4, 6 and 16 input channels c 24 V. b 3 digital output modules: v 4, 6, and 16 output channels c 24 V.
Description (continued) Advantys™ STB Distributed I/O Solution 0 Digital Input/Output Modules Description (continued) Mandatory items to be ordered separately I/O module bases in 3 widths depending on modules: Module size 1 2 3 Width 13.9 mm (0.547") 18.4 mm (0.72") 28.1 mm (1.
Description (continued) Advantys™ STB Distributed I/O Solution Digital Input/Output Modules Operating modes of digital output modules Output protection and reset following overload or short-circuit Digital output module Advantys STB Protection against short-circuit and thermal overload Actuator power supply protection Reset Diagnostics Basic modules STB DDO 3415, 3605, 3705 Internal electronic Via PDM fuse On elimination of the fault Per group of 2 channels Standard modules STB DDO 3200, 3230 Ac
Description (continued) Advantys™ STB Distributed I/O Solution 0 Digital Input/Output Modules Hot swapping and cold swapping of output modules Swapping Basic digital output module Standard digital output module not configured, “mandatory” Standard digital output module configured, “mandatory” Hot swap: Basic NIM Standard NIM (3) The other I/O modules remain The other I/O modules remain operational (1) operational (2) Cold swap All types of NIM All I/O modules and PDM power distribution modules can b
Advantys™ STB Distributed I/O Solution Characteristics 0 Direct current digital input modules Characteristics of DC digital input modules Type of module Range Number of channels STB DDI 3230 Standard 2 DDI 3425 Basic 4 Input nominal values Voltage Type (IEC/EN 61131-2) V c 24 Type 2 Type 1+ Input limit values Voltage Min. current At state 0 Voltage Max. current Input voltage values Permanent voltage Absolute maximum voltage Hz V mA V mA V V – c 11...30 6 2.5 c - 3...+ 5 2 1.2 c 30 c 56 for 1.
Advantys™ STB Distributed I/O Solution Characteristics (continued) 0 Direct current digital output modules Characteristics of DC digital output modules Type of module Range Number of channels Nominal values of outputs Voltage Current/channel Output logic Default User-configurable setting (1) Output voltage values Permanent voltage Absolute maximum voltage Response time STB DDO 3200 Standard 2 V A c 24 0.
Advantys™ STB Distributed I/O Solution Characteristics (continued) Alternating current digital input modules Characteristics of AC digital input modules Type of module Range Number of channels Input nominal values Voltage V Type (IEC/EN 61131-2) Input logic Default User-configurable setting (1) STB DAI 5230 Standard 2 a 115, (50/60 Hz) Type 1 – – Input response time Off-to-on On-to-off ms ms 1.5 network period 1.
Advantys™ STB Distributed I/O Solution Characteristics (continued) 0 Alternating current and relay digital output modules Characteristics of AC and relay output modules Type of module Range Number of channels Output nominal values Output logic Voltage limits Response time STB DRC 3210 Standard 2 “NO/NC” STB DRA 3290 STB DAO 5260 2 “NO” and “NC” 2 Voltage V c 24, a 115/230 a 115 Current per channel/contact A 2 at c 24 V 7 at c 24 V 2 at 30°C (86°F) 2 at a 230 V 7 at a 230 V 1 at 60°C (
Catalog numbers Advantys™ STB Distributed I/O Solution 0 Digital Input/Output Modules Catalog numbers Basic digital input modules Input voltage c24 V Number of channels 4 Compliance Catalog number IEC/EN 61131-2 Type 1+ STBDDI3425 Weight kg 0.111 6 Type 1 STBDDI3615 0.112 16 Type 3 STBDDI3725 0.086 Standard digital input modules Input voltage Number of channels 2 Compliance Catalog number IEC/EN 61131-2 Type 2 STBDDI3230 4 Type 1+ STBDDI3420 0.111 6 Type 1 STBDDI3610 0.
Advantys™ STB Distributed I/O Solution Catalog numbers (continued) 0 Digital Input/Output Modules Catalog numbers (continued) Mandatory separate parts Description Base width I/O bases STBXBA1000 Weight kg 0.024 STB DAI STB DAO STB DRC STB DRA STBXBA2000 0.028 STBXBA3000 0.048 For I/O modules STB DDI STB DDO Catalog number STBXTS1100 Weight kg 0.006 Spring-type STB DDI STB DDO STBXTS2100 0.006 Screw-type STB DAI STB DAO STB DRC STB DRA STB DAI STB DAO STB DRC STB DRA STBXTS1110 0.
Advantys™ STB Distributed I/O Solution Connections 0 Digital Input/Output Modules Connections Direct current digital input modules STB DDI 3230 STB DDI 3420/3425 STB DDI 3610/3615 A A 1 2 3 4 5 6 + Sensor 1 + IN – or Sensor 1 – + Sensor 2 – Sensor 3 Sensor 4 Sensor 5 Sensor 6 Sensor 7 Sensor 8 1 2 3 4 5 6 Sensor 1 Sensor 2 Sensor 3 B Sensor 3 – + Sensor 4 – B 1 2 3 4 5 6 IN IN 1 2 3 4 5 6 Sensor 4 Sensor 5 Sensor 6 1 three-wire sensor per input group (1) B A Sensor 2 IN
Connections (continued) Advantys™ STB Distributed I/O Solution 0 Digital Input/Output Modules Connections (continued) Alternating current digital input modules STB DAI 5230 STB DAI 5260 A Sensor 1 A 1 L 2 IN N 3 1 Sensor 1 (1) a 115 V 2 IN N 3 4 4 5 or 5 B B 1 Sensor 2 2 3 1 (1) Sensor 2 2 a 115 V 3 IN 4 4 5 5 (1) Link internal to module STB DAI 7220 A 1 L Sensor 1 2 IN N 3 4 5 or B 1 Sensor 2 2 3 4 5 49 This document provided by Barr-Thorp Electric Co., Inc.
Connections (continued) Advantys™ STB Distributed I/O Solution 0 Digital Input/Output Modules Connections (continued) Direct current digital output modules STB DDO 3200 STB DDO 3230 1 three-wire actuator and 1 two-wire actuator with external c 24 V power supply 0.5 A A 1 2 3 4 5 6 + Actuator 1 – (1) or 1 2 3 4 5 6 – A + (1) A 1 2 3 4 5 6 – or B Actuator 2 (2) 2.5 A Actuator 1 2 two-wire actuators powered via PDM 1 2 3 4 5 6 Actuator 1 (2) – B 2.
Advantys™ STB Distributed I/O Solution Connections (continued) 0 Digital Input/Output Modules Connections (continued) Alternating current digital output modules STB DAO 5260 STB DAO 8210 A A 0.
Selection guide Advantys™ STB Distributed I/O Solution Analog input modules Applications Analog input modules Voltage Number of channels 2 Range 0…10 V - 10…+ 10 V Resolution 10 bits 9 bits + sign Response time 5 ms for both channels Acquisition period – Acquisition or update time 10 ms for both channels Internal power supply for 3-wire inputs Yes Connections Two STB XTS 1100 screw-type connectors or STB XTS 2100 spring-type connectors (6-channel) Base STB XBA 1000 PDM power distribu
0 Analog input modules Current Multi range 2 4 4…20 mA 0…20 mA 4…20 mA and 0...20 mA 10 bits 12 bits 15 bits + sign 5 ms for both channels 8 ms for 4 channels 2 4…20 mA, 0...20 mA and HART protocol tolerant Thermocouples B, E, J, K, R, S and T Temperature probe Pt 100, Pt 1000, Ni 100, Ni 1000, Cu 10 ± 80 mV 80 ms for 4 channels – 85 ms for 4 channels 150...
Selection guide Advantys™ STB Distributed I/O Solution 0 Analog output modules Applications Analog output modules Voltage Number of channels 2 Range 0...10 V -10…+10 V 0...+ 10 V, - 10...
0 Analog output modules Current 2 4…20 mA 0…20 mA 4…20 mA 0…20 mA 10 bits 12 bits 15 bits + sign 20 mA 3 ms for both channels 4 ms for both channels – 25 ms for both channels – No Two STB XTS 1100 screw-type connectors or STB XTS 2100 spring-type connectors (6-channel) STB XBA 1000 STB XBA 2000 c 24 V STB PDT 3100/3105 c 1500 V for 1 minute c 200 V c 30 V (when actuator voltage is separate from logic bus voltage) – 4 mA on 2 channels (3) (2) Yes Yes, time-lag fuse on the PDM power distr
Advantys™ STB Distributed I/O Solution Presentation, description Analog input/output modules Presentation The STB analog inputs allow the acquisition of various analog values encountered in industrial applications. The STB analog outputs are used to control analog field devices such as variable speed drives, proportional control valves, etc.
Advantys™ STB Distributed I/O Solution Characteristics 0 Analog input modules Characteristics of analog input modules Type of module Type Number of channels STB Range Resolution bits AVI 1270 Standard 0…10 V ± 10 V 10 11 + sign Response time ms Cold swap Hot swap 5 for both channels Complies with IEC/EN 61131-2 Update time ms Input filter 10 for 2 channels Single low-pass filter with cut-off frequency of 25 Hz Integral linearity % of full scale ± 0,2 Monotonic Differential linearity
Advantys™ STB Distributed I/O Solution Characteristics (continued) Analog input modules Characteristics of analog input modules (continued) Type of module Type Number of channels STB Range bits Resolution ACI 1230 Standard ACI 0320 Standard 4 4…20 mA 0…20 mA (1) 4…20 mA and 0…20 mA 10 12 15 + sign ACI 8320 Standard 25 mA at c 50 V Maximum input Response time Swapping ACI 1225 Basic 2 ms ART 0200 Standard 2 multi ranges in any configuration Pt 100, Pt 1000, Ni 100, Ni 1000 and Cu 10 2, 3
Characteristics (continued) Advantys™ STB Distributed I/O Solution 0 Analog input modules Detailed characteristics of STB ART 0200 analog input module Thermocouple range Temperature unit Nominal values B E °C or °F (°C by default) °C (°F) 130 to - 270 to 1,820 °C + 1,000 °C (266 to (- 518 to 3,308 °F) + 1,832 °F) 0.
Advantys™ STB Distributed I/O Solution Characteristics (continued) Analog output modules Characteristics of analog output modules Type of module Type Number of channels STB AVO 1255 Basic 2 STB AVO 1265 STB AVO 1250 Standard Range 0... 10 V ± 10 V 0... 10 V ± 10 V 9 + sign 12 11 + sign Resolution bits 10 Output current per channel mA 5 Response time ms 3 Swapping Cold swap Hot swap Yes Yes, depending on NIM and mandatory nature of module.
Advantys™ STB Distributed I/O Solution Characteristics (continued) 0 Analog input/output modules Characteristics of analog output modules Type of module Type Number of channels STB ACO 1225 Basic 2 STB ACO 1210 Standard STB ACO 0220 Range 4... 20 mA 0... 20 mA (1) 12 4... 20 mA and 0... 20 mA 15 + sign Resolution bits 10 Output current per channel mA 20 Response time ms 3 Swapping Cold swap Hot swap – Yes Yes, depending on NIM and mandatory nature of module.
Catalog numbers Advantys™ STB Distributed I/O Solution 0 Analog input/output modules Catalog numbers Standard analog input modules Input signal Number of channels ±10 V 2 0…20 mA 2 4...20 mA and 0...20 mA 4 4...20 mA and 0...20 mA, HART 4 Thermocouples ± 80 mV 2 Resolution (bits) 11 + sign 12 15 + sign 15 + sign 15 + sign Catalog number STBAVI1270 STBACI1230 STBACI0320 STBACI8320 STBART0200 Weight kg 0.115 0.116 – – – Basic analog input modules Input signal -10…+10 V 0...
Advantys™ STB Distributed I/O Solution Catalog numbers (continued) 0 Analog input/output modules Catalog numbers Mandatory separate parts Description I/O base Description Removable connectors (6 contacts) (1) Base width For I/O modules 13.9 mm (0.54") STB AVI STB ACI 1230/1225 STB ART STB AVO STB ACO 18.4 mm (0.72") STB ACI 0320/8320 Catalog number STBXBA1000 Weight kg 0.
Advantys™ STB Distributed I/O Solution Connections 0 Analog input/output modules Connections Analog input modules STB AVI 1255/1270/1275 2 isolated analog sensors, external c 24 V power supply 2 analog sensors, c 24 V supplied by PDM A + (1) U Sensor 1 – Sensor 1 – U – 0V B c 24 V 1 2 3 4 5 6 (1) U Sensor 2 1 2 3 4 5 6 (1) + B + A c 24 V 1 2 3 4 5 6 1 2 3 4 5 6 (1) + Sensor 2 U – 0V + – c 24 V STB ACI 1225/1230 2 isolated analog sensors, external c 24 V power supply 2 analog
Connections (continued) Advantys™ STB Distributed I/O Solution 0 Analog input/output modules Connections (continued) Analog input modules STB ART 0200 2 and 3-wire temperature probes 2-wire temperature probes for highly disturbed operating environments A Sensor 1 2-wire A 1 2 3 4 5 6 (1) U (2) Sensor 1 4-wire U (1) B Sensor 2 3-wire U B 1 2 3 4 5 6 (1) 1 2 3 4 5 6 (2) Sensor 2 4-wire U (1) 1 2 3 4 5 6 2-wire thermocouple and voltage sensor (mV) A Sensor 1 2-wire thermocouple 1 2 3 4
Advantys™ STB Distributed I/O Solution Connections (continued) Analog input/output modules Connections (continued) Analog output modules STB AVO 1255/1265/1250 2 isolated analog actuators 2 analog actuators, c 24 V supplied by PDM A Actuator 1 + (1) U – (1) – + U – 0V B c 24 V 1 2 3 4 5 6 + U 1 2 3 4 5 6 (1) Actuator 1 B Actuator 2 A c 24 V 1 2 3 4 5 6 Actuator 2 + 1 2 3 4 5 6 (1) U – 0V + – 24 VDC STB ACO 1225/1210 2 isolated analog actuators 2 analog actuators, c 24 V supplied
Connections (continued) Advantys™ STB Distributed I/O Solution 0 Analog input/output modules Connections (continued) Analog output modules STB ACO 0220 2 isolated analog sensors, external c 24 V power supply A 1 2 3 4 5 6 – Actuator 1 I (1) + c 24 V – B 1 2 3 4 5 6 – Actuator 2 I (1) + c 24 V – 2 analog actuators, c 24 V supplied by PDM A + Actuator 1 1 2 3 4 5 6 (1) I – B Actuator 2 + 1 2 3 4 5 6 (1) I – 2 analog actuators, c 24 V supplied by PDM A c 24 V Actuator 1 1 2 3 4
Advantys™ STB Distributed I/O Solution Description Parallel interface module STB EPI 2145 TeSys ® Model U and TeSys ® Quickfit Applications Description The application-specific, parallel interface module STB EPI 2145 is a component of the Advantys STB island designed for the remote connection of TeSys Model U starter-controllers and TeSys Quickfit prewired motor-starters.
Description (continued) Advantys™ STB Distributed I/O Solution 0 Parallel interface module STB EPI 2145 TeSys ® Model U and TeSys ® Quickfit Applications 1 3 2 4 5 5 TeSys Model U starter control application Presentation of the TeSys Model U starter-controller The TeSys Model U starter-controller is a direct motor-starter which performs the following functions: b Protects and controls single phase or 3-phase motors: v disconnects power, v protects against overcurrent and short-circuit, v protects aga
Advantys™ STB Distributed I/O Solution Description (continued) TeSys® Quickfit for motor-starter components TeSys Quickfit components for motor-starters TeSys Quickfit is a modular system which standardizes and simplifies the installation of motor-starters. Combined with circuit-breakers GV2 ME and TeSys® Model D contactors (LC1) from 9 to 25 A, TeSys Quickfit facilitates the installation of motor-starters with spring-type terminal up to 11 kW/400V.
Advantys™ STB Distributed I/O Solution Characteristics 0 Parallel interface module STB EPI 2145 TeSys ® Model U and TeSys ® Quickfit Applications Characteristics Type of module Cold swapping Hot swapping STB EPI 2145 Yes Yes, depending on NIM and mandatory nature of module.
Catalog numbers Advantys™ STB Distributed I/O Solution 0 Parallel interface module STB EPI 2145 TeSys® Model U and TeSys® Quickfit Applications Catalog numbers TeSys Model U starter-controller module Type of power supply c Voltage Catalog number 24 V STBEPI2145 Weight kg 0.165 Mandatory separate parts Designation Base 28.1 mm(1.
Advantys™ STB Distributed I/O Solution Schematic diagrams 0 Parallel interface module STB EPI 2145 TeSys® Model U components TeSys® Model U starter-controllers: Remote control Simple connection of a parallel interface module STB EPI 2145 to 4 TeSys Model U starter-controllers for remote control via PLC. For each TeSys Model U starter-controller: b LU 9BN11 or LU 9BM1: Supplied with TeSys Model U base. b LUF C00, parallel communication module: to be ordered separately. b 1 RJ45 cable.
Advantys™ STB Distributed I/O Solution Presentation, description 0 Parallel interface module STB EPI 1145 Tego ® Power applications Presentation The STB EPI 1145 parallel interface is a component of the Advantys STB island designed for the remote connection of 8 motor-starters (or 4 motor-starters in both directions). These TeSys ® Model D motor-starters use the Tego Power installation assistance system.
Advantys™ STB Distributed I/O Solution Characteristics, catalog numbers 0 Parallel interface module STB EPI 1145 Tego ® Power applications Characteristics Electrical characteristics Type of module Swapping Cold swap Hot swap STB EPI 1145 Yes Yes, depending on NIM and obligatory nature of module.
Advantys™ STB Distributed I/O Solution Presentation, description Counter module STB EHC 3020 Presentation Counting parts or events, grouping objects, controlling incoming and outgoing data streams, and measuring lengths or positions all require counting functions. The STB EHC 3020 counter module performs these functions for an Advantys STB automation island (controlled by a master connected to the island) with a maximum counting frequency of 40 kHz.
Functions Advantys™ STB Distributed I/O Solution 0 Counter module STB EHC 3020 Operation Counter channel block diagram IN A and IN B counting inputs Output function block Counter block EN and RST auxiliary inputs Output function block High threshold Low threshold Island bus master Output for c 24 V 0.
Characteristics Advantys™ STB Distributed I/O Solution Counter module STB EHC 3020 Functional characteristics Configurable functions Number 1 of the 6 configurable functions (using the Advantys configuration software) Frequency meter This basic function measures the frequency received on the IN A input. This frequency is always expressed in Hz (number of pulses per second), with a precision of 1 Hz. Also measures the speed in units per second.
Advantys™ STB Distributed I/O Solution Characteristics (continued) 0 Counter module STB EHC 3020 Characteristics Electrical characteristics Type of module Frequency on counting inputs Swapping kHz Cold swap Hot swap STB EHC 3020 1 channel, up to 40 (1) Yes Yes, depending on NIM and mandatory nature of module.
Advantys™ STB Distributed I/O Solution Catalog numbers 0 Counter module STB EHC 3020 Catalog numbers Designation Counter module 1 channel 40 kHz Input type Catalog number 2/3 wire c 24 V detectors Incremental encoder c 24 V Mechanical contacts STBEHC3020 Weight kg – Mandatory separate parts Designation STB XBA 3000 Use Catalog number Base 28.1 mm (1.
Connections Advantys™ STB Distributed I/O Solution 0 Counter module STB EHC 3020 Connections Connection to STB XTS 2150 removable terminal block for spring-loaded terminals + Input IN A IN – Input IN B Output OUT 1 1 3 5 7 9 11 13 15 17 2 4 6 8 10 12 14 16 18 + Input EN IN – Input RST Output OUT 2 Note: The c 24 V power supplies for the sensors and actuators are provided by the STB PDT 3100 power distribution module via the sensor and actuator buses of the Advantys STB island.
Advantys™ STB Distributed I/O Solution Presentation Configuration and debugging software Presentation Advantys STB SPU 1ppp software is a tool for configuring and debugging the range of distributed I/O solutions Advantys STB, OTB (IP20 protection) and FTB/FTM (IP67 protection). It also allows debugging and diagnosis of distributed I/O islands while in operation.
Advantys™ STB Distributed I/O Solution Functions 0 Configuration and debugging software Functions Module Editor The editor gives access to 4 tabs, depending on the way in which the island is connected to the network or fieldbus: General, Properties, I/O Image and Diagnostics. “General” tab This read-only tab (island online or offline), provides general information and displays the key technical characteristics of the selected module.
Functions (continued) Advantys™ STB Distributed I/O Solution Configuration and debugging software Functions (continued) “Diagnostics” tab This tab allows the user to perform diagnostics for the island connected to the PC terminal where the Advantys configuration and debugging software resides.
Functions (continued) Advantys™ STB Distributed I/O Solution 0 Configuration and debugging software Functions (continued) Export of user labels (“tags”) The Advantys software allows you to create labels (symbol names) for all objects and I/O parameters of the Advantys STB configuration. The “File/export” function exports these names at the same time as the mapping, regardless of the fieldbus or network used. This information is directly usable on all controllers.
Functions (continued) Advantys™ STB Distributed I/O Solution Configuration and debugging software Functions (continued) Reflex Functions Editor For applications requiring short response times (< 3 ms), the Advantys STB Distributed I/O Solution allows you to create reflex functions using the configuration and debugging software. The reflex functions work directly at the level of the island output modules, so that they are not taken into account or processed by the island's master device.
Catalog numbers Advantys™ STB Distributed I/O Solution 0 Configuration and debugging software Catalog numbers The Advantys STB distributed I/O configuration and debugging software is multilingual and compatible with the operating systems Windows® 98 (Second Edition), Windows NT® 4.0 (Service Pack u 6), Windows 2000 (Service Pack u 1) and Windows XP (Service Pack u 1). Online help is available in 5 languages: English, French, German, Spanish and Italian. Internet Explorer (version 4.
Advantys™ STB Distributed I/O Solution Dimensions STB Npp 2212/1010 STB XBE 1000/1200/2100 and STB CPS 2111 5.05 (128.3) STB EHC 3020 2.95 (75) 0.72 (18.4) 3.74 (95) STB PDT 3100/2100 and 3105/2105 5.4 (137.3) 5.05 (128.3) 1.37 (35) 1.37 (35) 1.65 (42) 1.65 (42) 0.19 (5) 2.75 (70) 4.72 (120) 3.74 (95) with STB XBE 1200 and STB CPS 2111 only with STB XBE 1200 1.57 (40) 2.97 (75.5) only with STB XBE 2100 4.72 (120) 1.37 (35) 1.37 (35) 1.65 (42) 1.65 (42) 0.19 (5) 2.75 (70) 2.
Advantys™ STB Distributed I/O Solution Dimensions (continued) 0 STB DDI/DDO/DAI/DAOAVI/ACI/ART/AVO/ACO/DRC/DRA Side view STB DDI/DDO 3pp0 STB DDI/DDO 3pp5 STB AVI/ART/AVO STB ACI 1230/1225 STB ACO 1210/1225 STB DAI ppp0/DAO 8210 STB DRC 3210 STB ACI 0320/8320 STB ACO 0220 STB DRA 3290 2.75 (70) 1.65 (42) (1) A A B B B 1 1 2 2 3 3 4 4 5 5 1.37 (35) A 5.05 (128.3) (2) 3.74 (95) 0.72 (18.4) 0.54 (13.9) 2.97 (75.5) 1.10 (28.
Combinations Advantys™ STB Distributed I/O Solution 0 Magelis ® Combination with display units and operator interface terminals Application A display unit or Magelis XBT terminal can be connected directly to an Advantys STB island via the Modbus ® programming port. 1 2 3 2 3 4 1 STB NCO 2212 (door open) and STB XCA 4002 cable 1 PLC. 2 Advantys STB distributed I/O island with standard type NIM communication module STB Npp 2212. 3 Modbus ® serial cable and adapter if required.
Combinations (continued) Advantys™ STB Distributed I/O Solution Magelis ® display Combination with and operator interface terminals 0 units Connection cables Magelis family XBT H Type XBT N (1) Compact display units XBT E Terminals Size Display units Adapter Length Cable – 2.5 m (2.73 yd) XBTZ988 – 2m (2.18 yd) 2.5 m (2.
Combinations (continued) Advantys™ STB Distributed I/O Solution Advantys™ High-density I/O modules and Telefast ® ABE 7 cabling system Using the Advantys Telefast ABE 7 cabling system Using the Advantys Telefast ABE 7 cabling system rationalizes and simplifies the cabling of enclosures. Far less space is required in the enclosure and the Advantys Telefast ABE 7 base replaces the connection terminals at the bottom of the enclosure.
Combinations (continued) Advantys™ STB Distributed I/O Solution 0 High-density I/O modules and Advantys™ Telefast® ABE 7 cabling system Combinations of Advantys STB high-density modules and Advantys Telefast ABE 7 system Advantys STB module Module base High-density inputs STB DDI 3725 STB XBA 3000 18 pin connectors 2 screw spring STB XTS 1180 (1) STB XTS 2180 (1) Prewired cable 3 Characteristics Flying leads at Advantys module end. HE 10 connector at Advantys Telefast end. Wire cross-section 0.
Combinations (continued) Advantys™ STB Distributed I/O Solution Advantys™ High-density I/O modules and Telefast® ABE 7 cabling system Examples of combinations for logic input module STB DDI 3725 Voltage Advantys base Telefast ABE 7 V c 48 a 48 a 115 a 230…240 ABE7S16E2E1 ABE7S16E2E0 ABE7S16E2F0 ABE7S16E2M0 Examples of combinations for logic output module STB DDO 3705 Type Relay Relay Relay Relay Relay Static Static Static Economy relay Economy relay Voltage V c 24 Current per channel A 0.5 0.
Combinations (continued) Advantys™ STB Distributed I/O Solution 0 Advantys™ High-density I/O modules and Telefast® ABE 7 cabling system Module connections STB DDI 3725 - TSX CDP p01 Important: The inputs must be powered via the Advantys STB DDI 3725 module. (1) STB DDI 3725 Left Channel connector A IN Terminal no. 1 PDM V1 + (1) 2 I1 3 – 4 I2 5 – 6 I3 7 – 8 I4 9 PDM V1 10 – 11 I5 12 – 13 I6 14 – 15 I7 16 – 17 I8 18 – TSX CDP p01 HE 10 Terminal no.
Presentation Advantys™ STB Distributed I/O Solution Phaseo® 0 Regulated Power Supplies ABL 7 power supplies The Phaseo® ABL 7 range of power supplies is designed to provide the DC voltage required by the control circuits of automation system equipment. Split into three families, this range meets all the needs encountered in industrial, commercial and residential applications.
Presentation (continued) Advantys™ STB Distributed I/O Solution Phaseo® 0 Regulated Power Supplies Using c 24 V b Using c 24 V enables so-called protection installations (PELV) to be built. Using PELV is a measure designed to protect people from direct and indirect contact. Measures relating to these installations are defined in publication NF C 12-201 and in standard IEC 364-4-41.
Selection Advantys™ STB Distributed I/O Solution Phaseo® Regulated Power Supplies Selection of power supplies The characteristics to be taken into account when selecting a power supply are: b the required output voltage and current, b the mains voltage available in the installation. This may however result in several products being selected as suitable. Other selection criteria must therefore be taken into account.
Advantys™ STB Distributed I/O Solution Characteristics Phaseo® 0 Regulated Power Supplies Technical characteristics Type of power supply Approvals Conformity to Security standards EMC Low frequency harmonic currents ABL 7RE UL, CSA, TÜV, CTick UL 508, CSA 22.2 no.
Advantys™ STB Distributed I/O Solution Characteristics (continued) Phaseo® 0 Regulated Power Supplies Derating The ambient temperature is a determining factor which limits the power that an electronic power supply can deliver continuously. If the temperature around the electronic components is too high, their life will be significantly reduced. Conversely, a power supply can deliver more than its nominal power if the ambient temperature remains largely below the rated operating temperature.
Combinations, catalog numbers, dimensions Advantys™ STB Distributed I/O Solution Phaseo® 0 Regulated Power Supplies Combinations of Phaseo single-phase power supplies with Advantys STB modules Type of Advantys STB modules Installation for Advantys STB with 1 power supply NIM network interface module PDM power distribution module STB Npp 2212/1010 STB PDT 3100/3105 (1) BOS bus extension module STB XBE 1200 Sensors Actuators Auxiliary power supply STB CPS 2111 ABL7RP2410 (10 A) 2 power supplies ABL7R
Technical information 0 Automation products certifications In some countries, certification of certain electrical components is enforced by law. A standard conformity certificate is then issued by the official organization. Each certified product must carry approval symbols when enforced. Use on board merchant navy vessels generally requires prior approval (= certification) of an electrical device by certain marine classification authorities.
Technical information 0 Automation products certifications Community regulations Marine classification Marine classification authorities Certified Pending certification Advantys STB Advantys Telefast ABE 7 ConneXium Magelis iPC Magelis XBT GT Magelis XBT F/FC/HM/PM Magelis XBT N/R Modicon M340 Modicon Momentum Modicon Premium (4) Modicon Quantum Modicon TSX Micro Twido ABS BV DNV GL LR RINA RMRS USA France Norway Germany UK Italy C.I.S.
Power consumption document Advantys™ STB Distributed I/O Solution 0 Power Consumption Principle The c 5 V logic power supply for the I/O modules is provided by the following modules: b NIM network interface module placed at the beginning of the primary segment. b BOS bus extension module placed at the beginning of each extension segment. b CPS auxiliary power supply placed within a segment.
Power consumption document (continued) Advantys™ STB Distributed I/O Solution 0 Power Consumption Segment I/O module reference Combined with base Removable connectors (1) PDM power distribution modules (standard/basic) STBDDI3420 STBDDI3425 STBDDI3610 STBDDI3615 STBDDI3725 STBDAI5230 STBDAI 5260 STB DAI7220 XBA 1000 XBA 1000 XBA 1000 XBA 1000 XBA 1000 XBA 3000 XBA 2000 XBA 2000 XBA 2000 XTS p100 XTS p100 XTS p100 XTS p100 XTS p100 XTS p180 XTS p110 XTS p110 XTS p110 PDT 3100/3105 PDT 3100/3105 P
Product reference index 170BNO67100 . . . . . . . 23 170MCI00700 . . . . . . . 23 170MCI02010 . . . . . . . . 22 170MCI02036 . . . . . . . . 22 170MCI02080 . . . . . . . . 22 170MCI02120 . . . . . . . . 22 170MCI10000 . . . . . . . . 23 170XTS02000 . . . . . . . . 22 490NAD91103 . . . . . . . 23 490NAD91104 . . . . . . . 23 490NAD91105 . . . . . . . 23 490NTW00002 . . . . . . . 21 490NTW00002 . . . . . . . 72 490NTW00005 . . . . . . . 21 490NTW00005 . . . . . . . 72 490NTW00012 . . . . . . 21 490NTW00012 .
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123 www.barr-thorp.
The efficiency of Telemecanique® branded solutions Used in combination, Telemecanique products provide quality solutions, meeting all your Automation & Control applications requirements. Software tools Operator dialog Motion control Networks & communication Interfaces & I/O Automation Detection Motor control Power supplies Mounting systems A worldwide presence Constantly available b More than 5 000 points of sale in 130 countries.
