FactoryCast User’s Guide For Quantum and Premium 890 USE 152 00 Version 2.
Data, Illustrations, Alterations Data and illustrations are not binding. We reserve the right to alter products in line with our policy of continuous product development. If you have any suggestions for improvements or amendments or have found errors in this publication, please notify us by e-mail at techcomm@modicon.com. Training Schneider Automation Inc. offers suitable further training on the system. Hotline See addresses for Technical Support Centers at the end of this publication.
FactoryCast User’s Guide For Quantum and Premium 890 USE 152 00 Version 2.
Document Set Quantum Ethernet Embedded Web Server Module User Guide 840 USE 115 00 Premium Ethernet User Guide TLX DSCOM PL7
Preface Preface The data and illustrations found in this book are not binding. We reserve the right to modify our products in line with our policy of continuous product development. The information in this document is subject to change without notice and should not be construed as a commitment by Schneider Electric, Inc. Schneider Electric, Inc assumes no responsibility for any errors that may appear in this document.
Preface 6 890 USE 152 00 Version 2.
Contents Chapter 1 Chapter 2 Introduction to FactoryCast .................................................. 11 What Is FactoryCast? ..................................................................................... Components of FactoryCast........................................................................... FactoryCast .................................................................................................... FactoryCast Configurator ..................................................
Contents viii Remote I/O Drop Module Pages .................................................................... 43 Section 3.6 Distributed I/O Diagnostics............................................................................. Distributed I/O Diagnostic Overview............................................................... Distributed I/O Drops Page ............................................................................ Distributed I/O Specific Drop Page......................................
Contents Setting Symbol Access................................................................................... Adding Direct Addresses ................................................................................ Direct Address Blocks and Symbol Security .................................................. Editing and Deleting Direct Addresses ........................................................... Saving the Namespace ................................................................................
Contents Section 7.2 Chapter 8 Creating a Data Template .............................................................................. Inserting Variables in a Data Template .......................................................... Inserting Direct Addresses in a Template ...................................................... Modifying Data Values ................................................................................... Saving a Data Template....................................................
Introduction to FactoryCast 1 At a Glance Purpose This chapter describes FactoryCast for Quantum and Premium, including its functions, components and system requirements. In This Chapter This chapter contains the following topics: 890 USE 152 00 Version 2.0 For This Topic... See Page...
Introduction to FactoryCast What Is FactoryCast? Overview FactoryCast is a software package that allows you to customize a Web site on the Embedded Web Server module. The site can be accessed via a browser to view and modify data from a Quantum or Premium programmable logic controller (PLC). Default Web Site FactoryCast provides all the Web pages and Java applets you need to view runtime data from your controller.
Introduction to FactoryCast Components of FactoryCast Overview Quantum Version Premium Version The three components of FactoryCast are: l FactoryCast Server l FactoryCast Configurator l FactoryCast Client For Quantum, the FactoryCast components are integrated as follows: This Component... Is Used To... 140 NOE 211 10 140 NOE 251 10 (Fiber Optic) Store the Web site on its Embedded Server. 140 NOE 771 10 Enhance web server performance and memory Concept v. 2.1 and higher Modsoft v. 2.
Introduction to FactoryCast FactoryCast Overview FactoryCast consists of HTTP and FTP servers embedded in a Quantum or Premium Ethernet option module. How It Works The servers contain a default set of diagnostic Web pages and Java applets. The user can add custom Web pages and applets for specific applications. Versions Schneider Automation offers three versions of the Embedded Server 14 Part Number Description Memory Avail.
Introduction to FactoryCast FactoryCast Configurator Overview You can use the FactoryCast Configurator to configure and maintain your Web site. You also can use it to create a Web-enabled database of variables (symbols) and direct addresses, which can be viewed and modified during run-time over the Web.
Introduction to FactoryCast FactoryCast Client Overview FactoryCast Run-Time Diagnostics consists of default Web pages, Java applets, a Data Editor, a Graphics Editor, and an Alarm Viewer. Default Web Components The default Web pages and Java applets allow you to display the status and configuration of the controller, Embedded Server module, other option modules and I/O modules.
Introduction to FactoryCast System Requirements Overview This section provides minimum system requirements for FactoryCast Configurator software. If FactoryCast Configurator programs are used simultaneously with other software packages, a more powerful configuration may be required. To Use the Configuration Tool Minimum system requirements are: Processor Pentium 166 Mhz (Pentium 200 Mhz recommended) Operating System Windows 95/98 or Windows NT 4.
Introduction to FactoryCast Installation Overview This section explains the FactoryCast installation procedure. FactoryCast comes on a compact disc and is self-installing. Once the disc has loaded onto your PC, follow the installation dialogs. Downloaded Files FactoryCast will download the following files during installation: Table 1: Quantum Modules Sys Diag Data Editor Graphic Editor Comm Intf wwwroot/classes Sys Diag.jar wwwroot/conf Gcnftcop.sys wwwroot/images module.gif miniplc.gif eight_io.
Introduction to FactoryCast Installation, continued Table 2: Premium Modules Sys Diag Data Editor Graphic Editor Alarm Viewer Comm Intf wwwroot/classes JL.jarSysDiag.jar wwwroot/conf business.pbf modules.pbf products.pbf xway.txtranges.pbf wwwroot/images anim1.gif backbtn.gif secure/system plccfg.htm wwwroot/classes RDE.jar secure/system rde.htm wwwroot/classes GDE.jar Widgets.jar secure/system gde.htm wwwroot/classes RAE.jar secure/system rae.htm wwwroot/images ack.gif ackall.gif dfb.gif gr7.
Introduction to FactoryCast 20 890 USE 152 00 Version 2.
Web Site Security 2 At a Glance Purpose Before you set up your Web site, you should give some thought to security. While data in a default Web site is read-only, data in a custom site can be write-enabled. You should consider carefully who has access to the site and which data can be modified. This chapter discusses security concerns and some security mechanisms available to FactoryCast users. In This Chapter 890 USE 152 00 Version 2.0 This chapter contains the following topics: For This Topic...
Web Site Security Internal Security Overview The Web site you create with the FactoryCast Configurator may be accessed over an intranet. FactoryCast Configurator provides two mechanisms to ensure that only authorized users view and modify your data. Security Mechanisms On intranets, FactoryCast Configurator provides security through: l Password entry l Write restrictions CAUTION SECURITY SETTINGS MAY BE CHANGED Keep strict control of access to the FactoryCast Configurator software.
Web Site Security Internal Security, Continued Write Restrictions In order to write register values or save templates to your Web site with the Data Editor or Graphic Editor, a user must enter an additional password for write access. Users who enter the write password can only modify variables, (symbols) and direct addresses which are set as write-enabled. When you create a Web-enabled database of variables and direct addresses, you can designate each element as read-only or write-enabled.
Web Site Security External Security Overview If your network is configured to allow users to view your site over the Internet, you have the same security concerns as for an intranet, but you have an extra mechanism to deal with them: a firewall. Firewall Architecture A firewall is a gateway from the Internet to your Embedded Server, as depicted below. You can use a firewall to restrict or deny access to your Web site.
Web Site Security External Security, Continued Network-Level Firewalls Network-level firewalls are frequently installed between the Internet and a single point of entry to an internal, protected network. ApplicationLevel Firewalls An application-level firewall acts on behalf of an application; for instance, FTP. It intercepts all traffic destined for that application and decides whether to forward that traffic to the application. Application-level firewalls reside on individual host computers.
Web Site Security 26 890 USE 152 00 Version 2.
Default Web Site for Quantum 3 At a Glance Purpose When you receive the Server, it already contains a default Web site with diagnostic pages and the Data Editor. You may view these pages and view direct addresses in the Data Editor simply by installing the module and configuring its IP address. To access the site, type the Domain name or IP address of the module in your browser and enter the default user name and password of “USER”.
Default Web Site for Quantum Section 3.1 Introductory Pages Overview Purpose When a user accesses the default Web site for Quantum, he first encounters a FactoryCast Home Page and then a Quantum Welcome Page. This section describes those two pages. In This Section This section contains the following topics: 28 For This Topic... See Page... FactoryCast Home Page 29 Quantum Welcome Page 31 890 USE 152 00 Version 2.
Default Web Site for Quantum FactoryCast Home Page Overview The FactoryCast Home Page is the first page a visitor will encounter. No password is required to access this page. Home Page This is how the FactoryCast Home Page looks: Continued on next page 890 USE 152 00 Version 2.
Default Web Site for Quantum FactoryCast Home Page, Continued Links Data Customize 30 The home page offers three links: l Diagnostics and Online Data Editor links to the default diagnostic Web pages and the Run Time Data Editor l Password Protected Custom Application will link to any Web pages you add to the site with password security l Custom Application will link to any Web pages you add to the site without password security The home page reports on your: l Operating system l Screen resolu
Default Web Site for Quantum Quantum Welcome Page Overview When a visitor clicks on the Diagnostics link on the FactoryCast Home Page, they are directed to the Quantum Welcome Page. They must supply a user name and password to view this page because it is in the protected area of the site. Welcome Page This is how the Quantum Welcome Page looks: Links The Quantum Welcome Page provides links to all of the Quantum diagnostic pages and to the Run-Time Data Editor and Graphic Editor.
Default Web Site for Quantum Section 3.2 Local Rack Diagnostics Configured Local Rack Page Overview The Quantum Configured Local Rack page displays the current configuration of the local rack, including the controller, Embedded Server module and any I/O modules. The rack can contain up to 16 slots. Sample Page Here is an example of a Configured Local Rack page: Continued on next page 32 890 USE 152 00 Version 2.
Default Web Site for Quantum Configured Local Rack Page, Continued Data Each module is displayed in its configured slot in the rack and the following information is provided: l A label at the top of the module tells what type it is. Question marks indicate that the module type is unknown or the slot is empty.
Default Web Site for Quantum Section 3.3 Controller Diagnostics Controller Status Page Overview The Controller Status Page provides up-to-date information about the controller and its configuration. Access this page by selecting the CPa module or the hyperlink at the bottom of the page. Sample Page Here is an example of a Controller Status page: Continued on next page 34 890 USE 152 00 Version 2.
Default Web Site for Quantum Controller Status Page, Continued Dynamic Data Some of the data provided on this page is dynamic. Dynamic data is constantly refreshed at a rate determined by the performance of the Embedded Server, network, and client CPU. Links Links at the bottom of the page connect to other major diagnostic pages. 890 USE 152 00 Version 2.
Default Web Site for Quantum Section 3.4 Ethernet Module Diagnostics Ethernet Module Statistics Page Overview The Ethernet Module Statistics page provides information about the status, transmit and receive statistics and errors for the Embedded Server module. Access this page by selecting the NOE module from the local rack or use the hyperlink at the bottom of the page.
Default Web Site for Quantum Ethernet Module Statistics Page, Continued Dynamic Data Some of the data provided on this page is dynamic. Dynamic data is constantly refreshed at a rate determined by the performance of the Embedded Server, network, and client CPU. The Zero Counters button allows you to set all data fields to zero. They will continue to be refreshed after this setting. Links 890 USE 152 00 Version 2.0 Links at the bottom of the page connect to other major diagnostic pages.
Default Web Site for Quantum Section 3.5 Remote I/O Diagnostics Remote I/O Diagnostics Overview Purpose In This Section 38 Several default Web pages provide information about configured remote I/O, including: l Remote I/O Status page l Configured Remote I/O page l Remote I/O Drop pages l Remote I/O Drop Module pages This section contains the following topics: For This Topic... See Page...
Default Web Site for Quantum Remote I/O Status Page Overview The Remote I/O Status page gives an overview of the status and health of the Remote I/O network communications. Access this page by selecting the CRP Drop down menu item, “Remote I/O Status”. Sample Page Here is an example of a Remote I/O Status page: Dynamic Data Some of the data provided on this page is dynamic. Dynamic data is constantly refreshed at a rate determined by the performance of the Embedded Server, network, and client CPU.
Default Web Site for Quantum Configured Remote I/O Page Overview The Configured Remote I/O page displays information about the Remote I/O Head Processor and the number of remote I/O drops. This page can be accessed by selecting the CRP (RIO Head) module in the Configured Local Rack Page described previously Sample Page Here is an example of a Configured Remote I/O page: Data The top half of the screen provides the current status (dynamic) and other data about the Remote I/O Head Processor.
Default Web Site for Quantum Remote I/O Drop Pages Overview When you click on the icon for a Remote I/O Drop Adapter on the Configured Remote I/O page, you reach a Remote I/O Drop page with detailed information about that drop. Sample Page Here is an example of a Remote I/O Drop page: Continued on next page 890 USE 152 00 Version 2.
Default Web Site for Quantum Remote I/O Drop Pages, Continued Data The top part of the page reports the current status of the drop adapter and the number of modules in the drop. The bottom part of the page provides an icon for each module in the drop. A label at the top of the module identifies the module type. Question marks indicate that the module type is unknown or the slot is empty.
Default Web Site for Quantum Remote I/O Drop Module Pages Overview When you click on a specific module on a Remote I/O Drop page, you reach a Remote I/O Module page with information about that module. Sample Page Here is an example of a Remote I/O Discrete Module page: Continued on next page 890 USE 152 00 Version 2.
Default Web Site for Quantum Remote I/O Drop Module Pages, Continued Data The top part of the screen provides information about the current status of the I/O module, its location, module type and input or output offset. The LED panel in the lower part of the screen displays the status of the discrete I/O points: Links 44 l Green indicates the point is active l Off indicates the point is not active l It displays analog register values in integer format.
Default Web Site for Quantum Section 3.6 Distributed I/O Diagnostics Distributed I/O Diagnostic Overview Purpose Several Web pages provide information about configured distributed I/O, including: l Distributed I/O Drops page l Distributed I/O Specific Drop page l Distributed I/O Module pages Distributed I/O pages can be accessed by selecting either the CPU or a NOM from the Configured Local Rack page assuming that Distributed I/O is configured in the controller.
Default Web Site for Quantum Distributed I/O Drops Page Overview When you select a module on the Configured Local Rack page configured for distributed I/O, you reach a page with detailed information about the distributed I/O networked drops controlled by that module. Sample Page Here is an example of a Distributed I/O drops page connected to the CPU: Continued on next page 46 890 USE 152 00 Version 2.
Default Web Site for Quantum Distributed I/O Drops Page, Continued Data The top half of the screen provides the current status (dynamic) and other data about the controller or NOM module running the distributed I/O network. The bottom half of the screen displays an icon for each distributed I/O drop. Links Click on a drop icon to get detailed information about each drop. Links at the bottom of the page connect to other diagnostic pages. The “<” back button returns to the previous page.
Default Web Site for Quantum Distributed I/O Specific Drop Page Overview When you click on a drop icon on the Distributed I/O Network page, you reach a Distributed I/O Drop page with information about that drop. Sample Page Here is an example of a Distributed I/O Drop page: Continued on next page 48 890 USE 152 00 Version 2.
Default Web Site for Quantum Distributed I/O Specific Drop Page, Continued Data The top part of the page reports the current status of the drop and the number of modules in the drop. The bottom part of the page provides an icon for each module in the drop. A label at the top of the module identifies the module type.
Default Web Site for Quantum Distributed I/O Module Page Overview When you click on a module icon on a Distributed I/O Drop page, you reach a Distributed I/O Module page with information about that module. Sample Page Here is an example of a Distributed I/O Module page: Continued on next page 50 890 USE 152 00 Version 2.
Default Web Site for Quantum Distributed I/O Module Page, Continued Data The top part of the screen provides information about the current status of the I/O module, its location, module type and input or output offset. The LED panel in the lower part of the screen displays the status of the discrete I/O points: Links 890 USE 152 00 Version 2.0 l Green indicates the point is active l Off indicates the point is not active l It displays analog register values in integer format.
Default Web Site for Quantum 52 890 USE 152 00 Version 2.
Default Web Site for Premium 4 At a Glance Purpose When you receive the Server, it already contains a default Web site with diagnostic pages and the Data Editor. To use the default Web site, you only have to complete the setup procedures, beginning with FactoryCast Configurator on page 79. This section describes the pages in the default Web site. In This Chapter This chapter contains the following sections: For This Topic... 890 USE 152 00 Version 2.0 See Section... On Page...
Default Web Site for Premium Section 4.1 Introductory Pages Overview Purpose When a user accesses the default Web site for Premium, he encounters first a FactoryCast Home Page and then a Premium Welcome Page. This section describes those two pages. In This Section This section contains the following topics: 54 For This Topic... See Page... FactoryCast Home Page 55 Premium Welcome Page 57 890 USE 152 00 Version 2.
Default Web Site for Premium FactoryCast Home Page Overview The FactoryCast Home Page is the first page a visitor will encounter. No password is required to access this page. Home Page This is how the FactoryCast Home Page looks: Continued on next page 890 USE 152 00 Version 2.
Default Web Site for Premium FactoryCast Home Page, Continued Links Data 56 The home page offers three links: l Diagnostics and Online Data Editor links to the default diagnostic Web pages and the Data Editor l Password Protected Custom Application will link to any Web pages you add to the site with password security l Custom Application will link to any Web pages you add to the site without password security The home page reports on your: l Operating system l Screen resolution l Browser typ
Default Web Site for Premium Premium Welcome Page Overview When a visitor clicks on the Diagnostics link on the FactoryCast Home Page, he is directed to the Premium Welcome Page. He must supply a user name and password to view this page. Welcome Page This is how the Premium Welcome Page looks: Links The Premium Welcome Page provides links to the Rack Viewer, the Data Editor, the Graphic Editor and the Alarm Viewer.
Default Web Site for Premium Section 4.2 Local Rack Diagnostics Rack Viewer Page Overview The Rack Viewer Page displays the current configuration of the local rack, including the controller, Embedded Server module and any I/O modules.
Default Web Site for Premium Rack Viewer Page, Continued Links Click on a module icon to obtain detailed information about that module. The CPU module icon (slot 1) contains two links. The top link leads to the FIP I/O Module Diagnostics page. The lower link leads to the PLC Personality page. A line leading down from the Rack#0 icon (to the left of the rack) is a link to the next rack. When you place your mouse over this link, it turns into a red arrow.
Default Web Site for Premium Section 4.3 Controller Diagnostics PLC Personality Page Overview The PLC Personality page provides up-to-date information about the controller and its configuration. Sample Page Here is an example of a PLC Personality page: Continued on next page 60 890 USE 152 00 Version 2.
Default Web Site for Premium PLC Personality Page, Continued Dynamic Data Links 890 USE 152 00 Version 2.
Default Web Site for Premium Section 4.4 Ethernet Module Diagnostics Ethernet Module Statistics Page Overview If you click on the Embedded Server module in the Rack Viewer, you will reach the Ethernet Module Statistics page. This page provides up-to-date information about the status, configuration and activity of the Embedded Server module. Sample Page Here is an example of an Ethernet Module Statistics page: Continued on next page 62 890 USE 152 00 Version 2.
Default Web Site for Premium Ethernet Module Statistics Page, Continued Dynamic Data Links 890 USE 152 00 Version 2.
Default Web Site for Premium Section 4.5 Option Module Diagnostics Option Module Diagnostics Overview Purpose In This Section Several default Web pages provide information about configured option modules, including: l FIP I/O Module Diagnostics page l Digital I/O Module Diagnostics page l Analog I/O Module Diagnostics page l Standard Module Diagnostics page This section contains the following topics: For This Topic... 64 See Page...
Default Web Site for Premium FIP I/O Module Diagnostics Page Overview If you click on the FIP I/O link on the controller icon in the Rack Viewer page, you will reach the FIP I/O Module Diagnostics page. FIP I/O Diagnostics FIP I/O Diagnostic pages in FactoryCast Client for Premium are accessible in Rack Viewer Applet or page form. Continued on next page 890 USE 152 00 Version 2.
Default Web Site for Premium FIP I/O Module Diagnostics Page, Continued Rack Viewer Navigation The following illustration represents the navigation page tree of the Rack Viewer Applet.
Default Web Site for Premium FIP I/O Module Diagnostics Page, Continued Rack Viewer Click on the Rack Viewer link. The applet starts and displays the current configuration of the local rack, including the controller, Embedded Server module and any I/O modules. Continued on next page 890 USE 152 00 Version 2.
Default Web Site for Premium FIP I/O Module Diagnostics Page, Continued FIP bus link If Premium has a CPU with FIP bus link: Click on the FIP I/O link and the first level diagnostic page of FIP I/O is displayed: In the center part of this page, meters about FIP I/O activity are displayed. There is also a list of FIP I/O devices that are faulted. Continued on next page 68 890 USE 152 00 Version 2.
Default Web Site for Premium FIP I/O Module Diagnostics Page, Continued FIP I/O Bus page In FactoryCast Client, there is a button at the bottom of the FIP I/O activity page, named Bus FIP I/O exploration. If you click on this button, the FIP I/O Bus page is displayed: Note: The button FIP I/O Bus exploration is enabled only if a FIPIO bus is configured in the PLC application. Otherwise, the button is disabled (grayed).
Default Web Site for Premium FIP I/O Module Diagnostics Page, Continued If the Base Module of FIP I/O device is modular type, a Communicator is displayed. If Base Module of FIP I/O Device is compact type, there is no Communicator.
Default Web Site for Premium FIP I/O Module Diagnostics Page, Continued Dynamic Data Links 890 USE 152 00 Version 2.0 The LEDs in the upper left hand corner of the screen provide a dynamic report on the FIP I/O module status: LED Color If On Meaning If On Meaning If Off RUN Green Link active Link inactive I/O Red Remote device in fault Remote device operating normally The back arrow will take you to the Rack Viewer page for the controller.
Default Web Site for Premium Digital I/O Module Diagnostics Page Overview If you click on a digital I/O module in the Rack Viewer, you will reach a Digital I/O Module Diagnostics page with detailed information about that module. Sample Page Here is an example of a Digital I/O Module Diagnostics page: Continued on next page 72 890 USE 152 00 Version 2.
Default Web Site for Premium Digital I/O Module Diagnostics Page, Continued Dynamic Data The LEDs in the upper lefthand corner of the screen provide a dynamic report on the module status: LED Color If On Meaning If On Meaning If Blinking Meaning If Off RUN Green Running normally --- Communication fault No error Faulty module ERR Red Module failure I/O Red Overloaded short circuit Terminal block fault or server/preactuator voltage fault No error +32 Green Channels 32 ...
Default Web Site for Premium Analog I/O Module Diagnostics Page Overview If you click on an analog I/O module icon in the Rack Viewer, you will reach an Analog I/O Module Diagnostics page with detailed information about that module. Sample Page Here is an example of an Analog I/O Module Diagnostics page: Continued on next page 74 890 USE 152 00 Version 2.
Default Web Site for Premium Analog I/O Module Diagnostics Page, Continued Dynamic Data Links 890 USE 152 00 Version 2.
Default Web Site for Premium Standard Module Diagnostics Page Overview If you click on any other type of module in the Rack Viewer page, you reach a Standard Module Diagnostics page with detailed information about that module. Sample Page Here is an example of a Standard Module Diagnostics page: Continued on next page 76 890 USE 152 00 Version 2.
Default Web Site for Premium Standard Module Diagnostics Page, Continued Dynamic Data The LEDs in the upper lefthand corner of the screen provide a dynamic report on the module status: LED Color If On Meaning If On Meaning If Blinking Meaning If Off RUN Green Running normally *** *** ERR Red Module fault Not configured No error I/O Red I/O event --- No error OTHER Yellow *** *** *** *** - The meaning depends on the module type.
Default Web Site for Premium 78 890 USE 152 00 Version 2.
FactoryCast Configurator 5 At a Glance Purpose The FactoryCast Configurator gives you the ability to manage your Web site.
FactoryCast Configurator Section 5.1 Setting Up a FactoryCast Server Setup Overview Purpose Follow the procedures in this section to set up any FactoryCast server. In This Section This section contains the following topics: For This Topic... 80 See Page...
FactoryCast Configurator Definitions - FactoryCast Configurator Top Menu Overview The Top Menu is a graphical user interface through which you create, edit or view your web page(s). Top Menu functions Locate your FactoryCast Configurator icon. Double click, OR: select the icon and click the right mouse button to activate the context window; select . The top menu appears.
FactoryCast Configurator Top Menu Control menu box This is the box in the upper left corner of the Top Menu that displays the FactoryCast Configurator icon. The Control box opens the Control Menu. This menu displays commands that allow you to restore, move, size, minimize, maximize, or close the current application. Continued on next page 82 890 USE 152 00 Version 2.
FactoryCast Configurator Top Menu, Continued The top menu bar contains the following drop-down menu items: File File enables you to perform functions that control your application. It contains the following application commands: Continued on next page 890 USE 152 00 Version 2.
FactoryCast Configurator Top Menu, Continued Commands The Commands menu items enable you to perform functions that control your programs. For example, Uploading and Downloading files to and from the server, Back-up and Restore of the website on the server, and the ability to Resynchronize with the PLC programming software. It has the following commands. Continued on next page 84 890 USE 152 00 Version 2.
FactoryCast Configurator Top Menu, Continued Server “Server” contains: Restore (module) defaults, Check Status, and set XWay address. “Plug-ins” allows you to choose which options will be downloaded to the Embedded Web Server. It has the following commands. Continued on next page 890 USE 152 00 Version 2.
FactoryCast Configurator Top Menu, Continued Language Choose the language in which you will be working. Continued on next page 86 890 USE 152 00 Version 2.
FactoryCast Configurator Top Menu, Continued Server Menu Items For the following “Server” information: l Restore Defaults: See Restoring the Web Server Module on page 147. l Status: Module status. See Checking Embedded Server Status on page 142. l Set XWay Address: See Setting the XWay Address on page 98 l Plug-Ins: Editors: See Data Editor on page 172, Graphic Editor on page 184, Alarm Viewer on page 221. l System Diagnostics Note: Only the Plug-ins which are checked off will be downloaded.
FactoryCast Configurator Starting the Tool Overview This section describes how to start the FactoryCast Configurator. Procedure Select the FactoryCast Configurator application from Program Files in the Start menu, or use the desktop shortcut. Result: The FactoryCast Configurator main window appears. Next Step 88 Creating a new configuration. 890 USE 152 00 Version 2.
FactoryCast Configurator Creating a New Configuration Overview In order to set up your Web site, you must create a new configuration. This section describes how to do that. Procedure From the FactoryCast Configurator menu bar, select File | New Configuration. Result: The Settings window appears Next Step 890 USE 152 00 Version 2.0 Setting passwords.
FactoryCast Configurator Setting Passwords Overview The first step in setting up your Web site is to specify the passwords for viewing and modifying data. When you create a new configuration, the Settings window appears automatically with the Passwords dialog. Use this dialog to set the passwords. Passwords Dialog The following illustration shows the fields in the Passwords dialog: Continued on next page 90 890 USE 152 00 Version 2.
FactoryCast Configurator Setting Passwords, Continued Default Settings Read Access Write Access Until you apply your own password settings: l The default user name is USER l The default HTTP password is USER l The default write password is USER Complete the first three fields of the dialog box to set the user name and password for viewing the Web site. Anyone who wants to view the Web site will be prompted for this user name and password. l HTTP User Name is limited to fifteen characters.
FactoryCast Configurator Setting Default Access Overview If you want to view and modify symbols (variables) in your Web site, complete the Default Access dialog. This dialog determines the initial security settings for all the symbols you will add to the Web site. Accessing the Dialog Select the Default Access tab on the Settings window. Result: The Default Access dialog appears. Continued on next page 92 890 USE 152 00 Version 2.
FactoryCast Configurator Setting Default Access, Continued Options Select one of the following radio buttons: l Write Enabled sets write access for all symbols (variables) as you add them to the configuration. A user who supplies the write password would be able to modify these symbols. l Read Only sets read-only access for all symbols (variables) as you add them to the configuration. Even if a user supplies the write password, he would not be allowed to modify these symbols.
FactoryCast Configurator Setting File Locations Overview Accessing the File Locations Dialog If you want to customize your Web site, use the File Locations dialog to tell FactoryCast Configurator where to find the following files or directories: Give the Location of... In Order To Add...
FactoryCast Configurator Setting File Locations, Continued Specifying File Locations Use the ellipsis buttons to the right of the text boxes to browse for the desired files and directories. Note: The logo file must be in .gif format and it must be named logo.gif. Applying File Locations Select Apply to save the File Locations without exiting the Settings window. Next Step Setting the IP address. 890 USE 152 00 Version 2.
FactoryCast Configurator Setting the IP Address Overview The final setting in the Settings window is the IP Address. Accessing the IP Address Dialog Select the IP Address tab on the Settings window. Result: The IP Address dialog appears. Setting the IP Address Enter the Host Name or IP Address of the Embedded Server. If you enter the Host Name, and you have a Domain Name Server [DNS] in your intranet, the correct IP address should appear automatically.
FactoryCast Configurator Setting the IP Address, Continued Applying the IP Address Select Apply to save the IP Address setting. If you are satisfied with your settings, select OK to save them and to exit the Settings window. Next Step Your next step depends on which server you are using and how much you intend to customize the Web site: l If you are using the Premium ETY Embedded Server, you must set the XWay Address.
FactoryCast Configurator Setting the XWay Address Overview XWay is a Telemecanique communications protocol. If you are using the Premium ETY Embedded Server, you must set its XWay Address. Accessing the XWay Address Dialog Select Server | Set XWay Address from the menu bar. Setting the XWay Address Enter the Host Name or IP Address, and the XWay Address of the Embedded Server. Result: The Set XWay Address Service dialog appears.
FactoryCast Configurator Setting the XWay Address, Continued Applying the XWay Address Select OK to download the XWay Address to the Premium ETY Embedded Server. Next Step Your next step depends on how much you intend to customize the Web site: 890 USE 152 00 Version 2.0 l If you are not creating a database of symbols (variables) and write-enabled direct addresses, you may download the settings to the server.
FactoryCast Configurator Downloading Settings to the Server Overview If you are not creating a database of symbols (variables) and write-enabled direct addresses for your Web site, you may download your settings to the Embedded Server and begin using your site. Procedure Follow the steps in the table below to store your settings in a configuration file and download the configuration to the Embedded Server. Step Action 1 Select File | Save As... from the menu bar. Result: The Save As window appears.
FactoryCast Configurator Downloading Settings to the Server, Continued Procedure, Continued Step Action 5 From the menu bar, select Commands | Download | Advanced | All of the Above to download the configuration to the Embedded Server. Result: A Download Confirmation dialog appears with the IP address and any host name of the Embedded Server.
FactoryCast Configurator Section 5.2 Creating a Namespace Overview Purpose A namespace is a Web-enabled database containing symbols (variables) and/or write-enabled direct addresses. This section describes how to use symbols from a software database and direct addresses to create a namespace for your Web site. In This Section 102 This section contains the following topics: For This Topic... See Page...
FactoryCast Configurator Importing Symbols Overview If you want to use symbols (variables) in the Data Editor, Graphic Editor or Alarm Viewer, you must include them in the namespace. The applets will not allow you to view symbols which are not found in the namespace. This section describes how to: Accessing Your Software Database l Add symbols into a namespace l Delete symbols from a namespace To access a Concept database, you must have the Concept software installed on your computer.
FactoryCast Configurator Importing Symbols, Continued Add Symbols Follow the steps in the table below to import symbols (variables) from a Concept or PL7 database into your namespace. Step Action 1 Click the Add button at the bottom of the Symbols window. Continued on next page 104 890 USE 152 00 Version 2.
FactoryCast Configurator Importing Symbols, Continued Add Symbols, Continued Step Action 2 Select a programming database file. Note: If the location of the software database file was entered in the Settings window, FactoryCast Configurator will skip this step. Result:The Lookup Variables window appears. It displays symbols associated with the database. Continued on next page 890 USE 152 00 Version 2.
FactoryCast Configurator Importing Symbols, Continued Add Symbols, Continued Step Action 3 Click on symbols to highlight them individually or in blocks. Press the Control key to highlight symbols which are not adjacent to one another. Note: The FactoryCast Configurator automatically filters out symbols with address ranges that are not within the configured PLC range.
FactoryCast Configurator Importing Symbols, Continued Add Symbols, Continued Step Action 5 To add more symbols, click the Add button at the bottom of the Symbols window and repeat steps 3 and 4. Deleting Symbols To delete a symbol from a namespace, select the symbol and click the Delete button at the bottom of the Symbol window. Next Step Setting symbol security. 890 USE 152 00 Version 2.
FactoryCast Configurator Setting Symbol Access Overview FactoryCast Configurator sets default access for each symbol (variable) as you add it to the namespace, based on your selection in the Default Access Settings dialog. This section discusses security considerations and describes two ways for you to modify the security setting for a symbol. Two Levels of Access Each symbol (variable) may be write-enabled or read-only.
FactoryCast Configurator Setting Symbol Access, Continued Using the Attributes Button to Set Access 890 USE 152 00 Version 2.0 Follow the steps in the table below to use the Attributes button to set symbol access: Step Action 1 Highlight a symbol in the Symbol window. 2 Click the Attributes button at the bottom of the window. 3 Select the access option. 4 Click OK.
FactoryCast Configurator Adding Direct Addresses Overview If you only want users to view direct addresses, you do not need to include them in the namespace. The The Data Editor and Graphic Editor can read any direct address. If you want users to be able to modify a direct address, you must include it in the namespace. Any direct address included in the namespace is automatically writeenabled. This section describes how to import direct addresses into a namespace.
FactoryCast Configurator Adding Direct Addresses, Continued Quantum Register Values Add Direct Addresses The following register ranges are valid for writing to the Quantum: Start Value End Value 000001 065536 400001 465536 600001 699999 Follow the steps in the table below to add direct addresses into a namespace: Step Action 1 Select the Write Enabled Direct Addresses tab in the Configurator window. Result: The Write Enabled Direct Addresses screen appears.
FactoryCast Configurator Adding Direct Addresses, Continued Adding Direct Addresses, Continued Step Action 2 Select the Add button at the bottom of the window. Result: The Add Block Direct Addresses dialog appears. 3 Enter a valid range of addresses for your Quantum or Premium controller. Note: If you are only using direct addresses in your namespace, you may specify any valid range for the controller.
FactoryCast Configurator Adding Direct Addresses, Continued Adding Direct Addresses, Continued Step Action 4 Select Apply to save the specified registers to the namespace without exiting the dialog. Otherwise, select OK to save the registers and return to the Write Enabled Direct Addresses window. Result: The direct address register ranges are displayed in the window. 5 To add more direct addresses, repeat steps 2 through 4. Continued on next page 890 USE 152 00 Version 2.
FactoryCast Configurator Adding Direct Addresses, Continued Overlapping Register Ranges 114 If the register range that you have specified overlaps with a range already in the namespace, FactoryCast Configurator merges them into a single range and notifies you with the following message. Select OK to acknowledge the message. 890 USE 152 00 Version 2.
FactoryCast Configurator Direct Address Blocks and Symbol Security Overview When you import a block of direct addresses into a namespace which already contains symbols (variables), you may inadvertently include addresses associated with symbols. This can create a conflict between the security setting for the symbol itself and for its address.
FactoryCast Configurator Direct Address Blocks and Symbol Security, Continued Conflict#2 If a symbol (variable) is imported into the namespace as read-only OR if you change its security setting from write-enabled to read-only, and that symbol is included in a block of direct addresses, FactoryCast Configurator sends you a message and removes the address from the block. When you receive the message, click OK.
FactoryCast Configurator Editing and Deleting Direct Addresses Overview This section describes how to edit or delete direct addresses in the namespace. Editing Direct Addresses Follow the steps in the table below to edit a block of direct addresses: Step Action 1 Highlight a block of addresses in the Write Enabled Direct Addresses window. 2 Click the Edit button at the bottom of the window. Result: The Edit Block Direct Addresses dialog appears.
FactoryCast Configurator Saving the Namespace Overview This section describes how to save a namespace as part of the configuration file. Procedure Follow the steps in the table below to save the namespace in your configuration file. Step Action 1 Select File | Save As... from the menu bar. Result: The Save As window appears. 118 2 Select the directory where you want to save the configuration file. 3 Enter a File name of sixteen characters or less. Configuration files require a .cfg extension.
FactoryCast Configurator Resynchronizing Your Namespace with Its Database Overview Over time, you may make changes to the Concept or PL7 database from which you created your namespace. The Configuration Tool will only notify you of differences between the database and your namespace when you try to make changes in the namespace. This section describes how the Configuration Tool notifies you and prompts you to resynchronize your namespace with the database.
FactoryCast Configurator Resynchronizing Your Namespace with Its Database, Continued No Differences Detected If no discrepancy is detected, the following window appears. Continued on next page 120 890 USE 152 00 Version 2.
FactoryCast Configurator Resynchronizing Your Namespace with Its Database, Continued Differences Detected If a discrepancy between the namespace and the database is detected, a notification appears in the ReSynchronization Status dialog. Discrepancies include: l A symbol in the namespace has been deleted from the database. l A symbol in the namespace has had its address or data type changed in the database.
FactoryCast Configurator Resynchronizing Your Namespace with Its Database, Continued To Resynchronize Resynchronizing will alter the item(s) that differ from the database. The Configuration Tool allows only one resynchronization per configuration session. Follow the steps in the table below: Step Action 1 Select Commands | Resyncronize PLC Database. 2 Select File | Save. Result: The Resyncronize Function changes the configuration to correct any discrepancies.
FactoryCast Configurator Section 5.3 Download Download Overview Purpose The Commands | Download menu provides several options for downloading part or all of the information you have provided to customize your Web site. This section describes those options and provides a download procedure. In This Section This section contains the following topics: 890 USE 152 00 Version 2.0 For This Topic... See Page...
FactoryCast Configurator Download Options Overview This section describes the options of the Commands | Download menu. Download Menu The following illustration shows the Commands | Download> menu. Protected This option allows you to download All Files from a specific directory or to download a Single File selected from any directory to the password protected area of an Embedded Server. Continued on next page 124 890 USE 152 00 Version 2.
FactoryCast Configurator Download Options, Continued Unprotected 890 USE 152 00 Version 2.0 This option allows the user to download All Files from a specific directory or to download a Single File selected from any directory to the unprotected area of an Embedded Server.
FactoryCast Configurator Download Options, Continued Download File l Goto Commands | Download | Protected | Any File. OR: l Goto Commands | Download | Unprotected | Any File. Pressing the “OK“ button causes verification of the file selection, including: valid path, valid file name, etc. and then download the file to wwwroot/secure/user OR: wwwroot/unsecure/user. See Download on page 123.
FactoryCast Configurator Download Options, Continued Download Directory l Goto Commands | Download | Protected | All Files. OR: l Goto Commands | Download | Unprotected | All Files. Pressing the “OK“ button causes verification of directory selection, including: valid path, valid directory name, validity of all files in the directory, etc. and then download the directory content to wwwroot/secure/user OR: wwwroot/unsecure/ user. See Download on page 123.
FactoryCast Configurator Download Options, Continued Advanced Menu This menu item allows you to selectively download files to modify the Embedded Server configuration or to configure multiple Embedded Servers performing the same function. Selecting only the files changed, you can save time on downloading. The following illustration shows the Commands | Download | Advanced menu.
FactoryCast Configurator Download Options, Continued Modified Home Page This option allows you to download only the Home Page [index.htm] once you have made modifications to it. The file is Qbf\software\wwwroot\index.htm for Quantum or Pbf\software\wwwroot\index.htm for Premium. The name of this file should remain index.htm. Logo File This option downloads your company logo file [logo.gif] to the default Web pages.
FactoryCast Configurator How to Download Overview This section provides a procedure for using any of the options on the Commands | Download menu. Memory Check FactoryCast Configurator checks how much space is available on the Embedded Server before downloading. If there is insufficient memory, an error message appears. Procedure Follow the steps in the table below to download information to the Embedded Server. Steps Action 1 Select an option from the Commands | Download menu.
FactoryCast Configurator Section 5.4 Upload Upload Overview Purpose The Commands | Upload menu provides options for uploading one file or all files within a directory on the FactoryCast server. This section describes those options and provides the upload procedure. This function is useful for getting a file from the FactoryCast server which you would like to modify. In This Section This section contains the following topics: 890 USE 152 00 Version 2.0 For This Topic... See Page...
FactoryCast Configurator Upload Options Overview This section describes the options of the Commands | Upload menu. Upload Menu The following illustration shows the Commands | Upload menu. Protected This option allows you to upload All Files from a specific directory or to upload a Single File selected from any directory in the password protected area of the FactoryCast server to a directory specified by you.
FactoryCast Configurator Upload Options, Continued Upload File l Goto Commands | Upload | Protected | Any File. OR: l Goto Commands | Upload | Unprotected | Any File. Upload allows you to retrieve a file or files from the web server so you can edit them on your PC. Pressing the “OK“ button causes the selected file to be uploaded from wwwroot/secure/user OR: wwwroot/unsecure/user to the Directory Selected.. See Upload on page 131.
FactoryCast Configurator Upload Options, Continued Upload Directory l Goto Commands | Upload | Protected | All Files. OR: l Goto Commands | Upload | Unprotected | All Files. Upload All Files allows you to retrieve an entire directory from the web server so you can edit them on your PC. Pressing the “OK“ button causes the selected directory content to be uploaded from wwwroot/secure/user OR: wwwroot/ unsecure/user to the Directory Selected. See Upload on page 131.
FactoryCast Configurator How to Upload Overview This section provides a procedure for using any of the options on the Commands | Upload menu. Procedure Follow the steps in the table below to upload information from the Server. Steps Action 1 Select an option from the Commands | Upload menu. Result: The Upload Conformation dialog appears with the IP address and host name of the FactoryCast.
FactoryCast Configurator Section 5.5 Remove Overview This section describes the options of the Commands | Remove menu. Purpose The Commands | Remove menu provides options for removing part or all of the files you have downloaded to customize your Web site. This section describes those options and provides a remove procedure. In This Section This section contains the following topics: For This Topic... 136 See Page... Remove Options 137 How to Remove 140 890 USE 152 00 Version 2.
FactoryCast Configurator Remove Options Remove Menu The following illustration shows the Commands | Remove menu. Protected This option allows you to remove All Files from a specific directory or to remove a Single File selected from any directory in the password protected area of the embedded server. Unprotected This option allows you to download All Files from a specific directory or to download a Single File selected from any directory in the unprotected area of the embedded server.
FactoryCast Configurator Remove Options, Continued Remove File l Goto Commands | Remove | Protected | Any File. OR: l Goto Commands | Remove | Unprotected | Any File. Remove File allows you to remove a file or files from the web server. Pressing the “OK“ button causes the selected file to be removed from wwwroot/secure/user OR: wwwroot/unsecure/user. See Remove on page 136.
FactoryCast Configurator Remove Options, Continued Remove Directory l Goto Commands | Remove | Protected | All Files. OR: l Goto Commands | Remove | Unprotected | All Files. Remove File allows you to remove a directory from the FactoryCast server. Pressing the “OK“ button causes the selected directory content to be removed from wwwroot/secure/user OR: wwwroot/unsecure/user. See Remove on page 136. A dialog with the following appears: 890 USE 152 00 Version 2.
FactoryCast Configurator How to Remove Overview This section provides a procedure for using any of the options on the Commands | Remove menu. Procedure Follow the steps in the table below to remove information from the Server. Step Action 1 Select an option from the Commands | Remove menu. Result: The Remove Confirmation dialog appears with the IP address and host name of the Embedded Server as well as a file path entry field.
FactoryCast Configurator Section 5.6 Web Site Maintenance Maintenance Overview Purpose In This Section 890 USE 152 00 Version 2.0 This section describes how to maintain your Web site, including: l Checking server status l Backing up files l Restoring files l Reflashing the module l Updating I/O module descriptions This section contains the following topics: For This Topic... See Page...
FactoryCast Configurator Checking Embedded Server Status Overview Memory Capacity The Configurator gives you a way to check: l Bytes of free memory in the Embedded Server l The file name of the last configuration downloaded to the Embedded Server Consult the table below to find out how much memory your Embedded Server provides for customizing your Web site: Embedded Server Model Memory Available for Customizing the Site Quantum 140 NOE 2x1 10 Customizable based on plug-ins configured Premium TSX E
FactoryCast Configurator Checking Embedded Server Status, Continued Procedure Follow the steps in the procedure below to check the server status: Step Action 1 Select Server | Status> from the menu bar. Result: The Module Status dialog appears. 2 Enter the Host Name or IP Address of the Embedded Server. Note: Since you do not need a Configuration file open to perform this function the Host name is not filled in by default. Continued on next page 890 USE 152 00 Version 2.
FactoryCast Configurator Checking Embedded Server Status, Continued Procedure, Continued Step Action 3 Select OK. Result: The Ethernet Module Status dialog appears. It displays the current configuration file for the Embedded Server and the number of bytes free in memory.. 4 144 Click OK to exit the Module Status dialog. 890 USE 152 00 Version 2.
FactoryCast Configurator Backing Up Files Overview The Commands | Backup option is used to archive the entire file contents of the Embedded Server. A zip file is created in the directory specified as result of the Backup operation. The contents of the backup can be used to restore the Embedded Server to the configuration at the time of the backup. Do Not Modify Backup Files The user should not make any modifications to the directory structures or files in the zip file.
FactoryCast Configurator Backing Up Files, Continued Procedure, Continued 146 Step Action 3 Enter the Path and File Name where you would like to store the backup file. Use the ellipses button to the right of the text box to browse for a location. 4 Click OK to begin the backup. 890 USE 152 00 Version 2.
FactoryCast Configurator Restoring the Web Server Module Overview The Commands | Restore option is used to restore the contents of a backup file to the FactoryCast. Procedure Follow the steps in the table below: Step Action 1 Select Commands | Restore. Result: The Restore dialog appears. 890 USE 152 00 Version 2.0 2 Enter the Host Name or IP Address of the Embedded Server. 3 Enter the Path and File Name of the backup file.
FactoryCast Configurator Restoring the Web Server Module, Continued Overview If the server fails or its files become corrupted through user error, you can use the Server | Restore Defaults option to restore the FactoryCast Configurator files. This menu item restores the selected module to the state in which it was shipped from the factory. This may take some time, so be prepared.
FactoryCast Configurator Restoring the Web Server Module, Continued Restore Defaults Command When “Restore Defaults” is selected, the module will be cleared (except rdt and gdt directories) and the default plug-ins will be downloaded again. Note: If “OK” is selected the module files will be restored to the selected packages. If “CANCEL” is selected, all selections will be cleared and the dialog dismissed. Continued on next page 890 USE 152 00 Version 2.
FactoryCast Configurator Restoring the Module, Continued Procedure Follow the steps in the table below: Step Action 1 Select Server | Restore Defaults. Result: The Initialize dialog appears. 150 2 Enter the Host Name or IP Address of the Embedded Server. 3 Select OK. 890 USE 152 00 Version 2.
FactoryCast Configurator Updating I/O Module Descriptions Overview Over time, the I/O module descriptions for the modules displayed in the default Web pages may become outdated. Schneider Automation will make available, from time to time, new I/O module descriptions to be downloaded to the Embedded Server module. When you receive a new I/O module description file from Schneider Automation, follow the procedure below to download the file to the server.
FactoryCast Configurator 152 890 USE 152 00 Version 2.
Adding Custom Pages to the Site 6 At a Glance Purpose You may choose to add your own Web pages to the site on the Embedded Server. The FactoryCast Configuration Tool allows you to protect them with the same passwords as the default pages or to put them in an unprotected area, where anyone can view them without a password. FactoryCast Configurator provides some simple Java applets you can include to create dynamic data from the controller right in your custom Web pages..
Custom Pages Section 6.1 Working with Custom Pages Overview Purpose In This Section 154 You may develop any pages you want to customize the FactoryCast Configurator site.
Custom Pages Downloading a Custom Home Page Overview If you want to replace the default home page with one of your own, you must take the following steps: l Back up the original FactoryCast configuration, so that you can restore it later if necessary l Move the supplied default home page to a secure place l Create a new home page or edit the existing page l Replace it with your home page l Download your home page to the Embedded Server Backing Up the Original Configuration Before you change th
Custom Pages Downloading a Custom Home Page, Continued What About Image Files? Any image files for your new home page should be placed in the same directory as your company logo. This directory is specified in the File Settings dialog. Image file names must conform to DOS 8.3 format (no more than eight letter file name and three letter extension) and should be lower case (ie. machine1.htm). Downloading Follow the steps in the table below to download your new home page to the Embedded Server.
Custom Pages Downloading Other Protected Pages Overview If you are adding supporting Web pages to the default Web site, you may choose to protect them with the same user name and password as the default pages. In order to add password-protected pages to the site, you must specify the directory where they are located and then download them to the server. Specifying File Locations Place the files for your Web pages and any images for the pages in a single directory.
Custom Pages Downloading an Unprotected Web Site Overview You may choose to have an unprotected Web pages. These are pages that: l Have read-only information l Can be accessed without a password Use the Commands | Download | Unprotected | All Files option to download unprotected Web pages to the Embedded Server. File Names and Location Before you can download unprotected Web pages to the Embedded Server, you must place the page and its image files in one folder.
Custom Pages Removing Unprotected Web Files Overview 890 USE 152 00 V.2 If you want to remove unprotected Web files from the Embedded Server, See Remove on page 136.
Custom Pages Section 6.2 Using FactoryCast’s Java Applets Overview Purpose This section describes how to use the Java Applets LiveLabelMgrApplet, LiveLabelApplet, LiveBeanMgrApplet, and LiveBeanApplet to include dynamic data from the controller on your Web pages. In This Section This section contains the following topics: 160 For This Topic... See Page...
Custom Pages Using the Applets on a Web Page Overview The supplied applets can be included on a Web page to query and display dynamic data from a Quantum or Premium controller without having to know or write Java code. LiveBeanMgr Applet The LiveBeanMgrApplet allows the Web page to display dynamic data from the controller. This applet must be included once on the page if any instances of LiveBeanApplet are included in the page. LiveBeanMgrApplet can be included on a Web page in two possible forms.
Custom Pages Using the Applets on a Web Page, Continued LiveLabelMgr Applet The LiveLabelMgrApplet allows the Web page to display dynamic data from the controller. This applet MUST be included once on the page if any instances of LiveLabelApplet are included on the page. Here is the HTML code that you use to include the applet on a page:
Custom Pages Using the Applets on a Web Page, Continued LiveBeanApplet The LiveBeanApplet is included one time for each variable (symbol) or direct address monitored/controlled on the Web page. For instance, if you are monitoring three variables, you would include the applet three times. LiveBeanApplet allows any graphic object (Java Bean) that was created with the Graphic Editor to be included on a Web page as a separate applet. (See Graphic Editor on page 184, for information on the Graphic Editor.
Custom Pages LiveBeanApplet LiveBeanApplet Parameters The LiveBeanApplet uses parameters to allow you to specify the graphic object to be presented by the applet and to set the applet’s background color. Parameter… Defines… LIBRARY The name of the graphic display which contains the graphic object that is to be presented by the applet. (This will be the same name that was used when the graphic display was saved with the Graphic Editor .) This parameter is required.
Custom Pages LiveBeanApplet Parameters, Continued LiveBeanApplet Example All instances of LiveBeanApplet that are included in a Web page follow the same pattern, with only the applet parameters and size varying for each instance. Here is the HTML code for including a LiveBeanApplet that will present the graphic object named “MyMeter” which was saved by the Graphic Editor as part of the graphic display, “Library 1”.
Custom Pages LiveLabelApplet Parameters, Continued Data Parameters, Continued Parameter... Defines... With Default Value... FORMAT The display format for the value.
Custom Pages LiveLabelApplet Parameters, Continued Format Parameters Size Parameters 168 The format parameters for the applet, their meaning and default values are shown below: Parameter... Defines... With Default Value... FOREGRND Foreground color of the applet. Acceptable values are: WHITE, LT_GRAY, GRAY, DK_GREY, BLACK, RED, PINK, ORANGE, YELLOW, GREEN, MAGENTA, CYAN, and BLUE. BLACK BACKGRND Background color for the applet. For acceptable values, see FOREGRND.
Custom Pages LiveLabelApplet Example #1 Overview The applet example in this section contains almost every applet parameter. Example Code Here is the HTML code for this example:
Custom Pages LiveLabelApplet Example #2 Overview This is an example of a minimal applet, using default values for most parameters. Example Code Here is the HTML code for this example:
Editors 7 At a Glance In This Chapter 890 USE 152 00 V.2 This chapter contains the following topics: For This Topic... See Page...
Editors Section 7.1 Data Editor Purpose Every default Web page contains a link to the Data Editor. The Data Editor is a Java applet that enables you to create dynamic data tables that are updated with run-time data from the PLC. This section describes how to use the Data Editor to view and modify the values of variables (symbols) and direct addresses. In This Section This section contains the following topics: For This Topic... 172 See Page...
Editors The Data Editor Spreadsheet Overview The Data Editor displays data in a spreadsheet with the following fields: l Variable Name l Address l Data Type l Value l Format l Status This section provides a snapshot of the spreadsheet and an explanation of each field. Spreadsheet Here is a Data Editor spreadsheet: Continued on next page 890 USE 152 00 V.
Editors The Data Editor Spreadsheet, Continued Variable Name Field The Variable Name column contains the names of Concept or PL7 variables (symbols). The only variables which may be used in the Data Editor are the ones in the namespace on the Embedded Server. If you try to enter a variable which is not in the namespace, a ‘variable not found’ message appears. Note: The Data Editor can only read values from a namespace which was created from the same program as the one running in the controller.
Editors The Data Editor Spreadsheet, Continued Address Field The Address column contains direct addresses and the addresses of Concept or PL7 variables. Any direct address may be viewed by entering its reference in this field. It does not have to be included in the namespace.
Editors The Data Editor Spreadsheet, Continued FIP I/O Addresses Address Type (R)ead or (W)rite Access %I\rs.2.d\m.c BOOLEAN R %Q\rs.2.d\m.c BOOLEAN R/W %Iw\rs.2.d\m.c.i WORD 16 R %Qw\rs.2.d\m.c.i WORD 16 R/W %Mw\rs.2.d\m.c.i WORD 16 R/W %Kw\rs.2.d\m.c.i WORD 16 R. r=rack number, s=slot number, c=channel number, i=range number d=device number, and m=module number Data Type Field The Data Type field contains the data type of the variable (symbol) or direct address.
Editors The Data Editor Spreadsheet, Continued Format Field Status Field The Format field contains the format type for displaying the value of the variable (symbol) or direct address. The following formats are available: Abbreviation Format Type bool Boolean dec Decimal hex Hexadecimal binary Binary ASCII bytes displayed as ASCII characters time day_hr_min_sec_ms The Status column contains messages about the status of communications with the variable (symbol) or direct address.
Editors Creating a Data Template Overview When you want to see the values of variables (symbols) or direct addresses, you enter the variable name or direct address on a Data Editor spreadsheet. The spreadsheet containing your data is called a data template. To Get a Fresh Spreadsheet A blank spreadsheet appears when you open the Data Editor.
Editors Inserting Variables in a Data Template Overview If you want to view or modify the value of a variable (symbol) in the namespace, you must insert that variable in a data template.
Editors Inserting Direct Addresses in a Template Overview If you want to view or modify the value of a direct address, you must insert that direct address in a data template. Two Ways to Insert Direct Addresses To insert a direct address(es) in a data template, you can: Using the Insert Rows Dialog l Type the address in an Address cell in an empty row of the spreadsheet and press the Enter key l Use the Insert Rows dialog Follow the steps in the table below to use the Insert Rows dialog.
Editors Modifying Data Values Overview You can use the Data Editor to modify the values of some variables (symbols) and direct addresses and send the new values to the controller. Restrictions on Modifying Data You can only modify the values of variables (symbols) or direct addresses which are write-enabled in the namespace.
Editors Saving a Data Template Overview If you save a data template, you can use it again to view or modify the same variables (symbols) or direct addresses. Procedure Follow the steps in the table below to save a data template: Step Action 1 Click the Password button from the Data Editor menu. Result: A Password dialog appears. 2 Enter the write password. 3 Click OK. Result: The Save button is enabled on the Data Editor menu. 4 Click the Save button.
Editors Using an Existing Data Template Overview Once you have saved a data template, you can use it to view or modify the values of the same variables (symbols) and direct addresses. Finding a Data Template A drop-down menu on the Data Editor lists all the data templates which have been saved. Retrieving a Data Template Select the data template you want from the dropdown menu. It will appear on a spreadsheet.
Editors Section 7.2 Graphic Editor Introduction This section describes the functions and features for the Graphic Editor. The Graphic Editor is a Java applet which enables you to create dynamic graphic displays, via a Web browser, using a set of pre-defined graphic objects. The Graphic Editor serves as both the editor for creating and modifying the displays and the run-time environment for viewing the displays as they are dynamically animated with run-time data from the PLC.
Editors Overview Top Window The Graphic Editor applet is divided into three windows. The Top Window provides the area for presenting all the user controls and dialogs for creating, saving, reading and editing a graphic display. The figure below shows the Graphic Editor applet with its initial top window and empty display and message windows. Display Window The Display Window provides the area for presenting the current graphic display.
Editors Overview, Continued Note: On most Embeded Servers you cannot download both the Data Editor and Graphic Editor because of memory restrictions. If you want both, you must remove an equivalent amount of plug-ins. Graphic Objects All the graphic objects that are provided with the Graphic Editor are capable of communicating with the PLC from which the Graphic Editor applet was downloaded. There is no additional “wiring” of the graphic objects with “communication objects”.
Editors Overview, Continued User Functions 890 USE 152 00 V.2 Most of the Graphic Editor’s user functions are available from the top window, which is discussed in Top Window User Functions on page 188. From the display window, you can directly manipulate a graphic object’s size and location. All properties of a graphic object (e.g., scaling values, labels, colors, PLC addresses of the run-time data) are set by means of the Property Sheet, which is described in Property Sheet on page 200.
Editors Top Window User Functions Overview The Graphic Editor applet's top window consists of several “dialog panels”, only one of which is shown at time. Switching from one dialog to another is done by clicking buttons on the current dialog. This section describes the dialog panels that comprise the top window. Top Dialog The “Top Dialog” is the dialog panel that is initially shown in the top window when the Graphic Editor applet is started.
Editors Top Window User Functions, Continued The controls of the “Top Dialog” provide the following functions: Save Dialog l Drop-down List. The drop-down list box shows all the graphic display files that have been saved to the web server module, and are available for retrieving. When you select a graphic display from this list, the graphic display currently visible in the window is replaced with the one selected.
Editors Top Window User Functions, Continued When the “Save Dialog” is presented, the name of the current graphic display is shown in the dialog’s text field. If the current graphic display has never been saved (i.e., a graphic display), then the text field is blank. Once you have either accepted the current name (a “save” operation) or provided a new name (a “save as” operation), then you can click the OK button to save the contents of the current graphic display to the web server module.
Editors Top Window User Functions, Continued Password Dialog The “Password”Dialog” allows you to enter the password that enables those user functions that modify graphic display files or PLC run-time data values. If you enter the correct password and click the “OK” button, then you will be allowed to save and delete the current graphic display. Correct password entry also permits you to write new values to the PLC (via those graphic objects that support writing values to a PLC, if any).
Editors Top Window User Functions, Continued Edit Dialog 192 The “Edit Dialog” allows you to select a graphic object for placement in the display window, and provides access to all of the graphic editing functions. The graphic objects that are available to you are presented in a set of palettes, with one palette visible at a time. 890 USE 152 00 V.
Editors Top Window User Functions, Continued The controls of the “Edit Dialog” provide the following functions: l The Drop-down List Box shows the set of palettes that are available. When you select the name of a palette from the list, the graphic objects that are in that palette are presented in the palette display area of the dialog. l The Palette shows the graphic objects that are in the current palette with an icon that depicts each graphic object's type (meter, button, etc.).
Editors Top Window User Functions, Continued Layout Dialog The “Layout Dialog” allows you to change the position and size of a group of graphic objects. The controls of the "Layout Dialog" provide the following functions: l For aligning graphic objects’ edges, the “Right”, “Bottom”, “Left”, and “Top” buttons cause the currently selected graphic objects to be moved so that their specified sides are at the same position. At least two graphic objects must be selected for these buttons to be enabled.
Editors Top Window User Functions, Continued l To automatically size graphic objects, use the “Width” and “Height” buttons to re-size the currently selected graphic objects so that either the widths or heights, respectively, of the objects match. At least two graphic objects must be selected for these buttons to be enabled. l The “Done” button causes the “Edit Dialog” to be shown again.
Editors Top Window User Functions, Continued The controls of the “Options Dialog” provide the following functions: 196 l The cell size of the grid can be changed by the entering the grid's column width and row height into the dialog's text fields. l If the “Show grid” check-box is checked, the grid will be drawn; otherwise, no grid will be shown.
Editors Display Window User Functions Overview The user functions available from the Graphic Editor display window include object selection, moving and sizing. All moving and sizing operations require that the graphic object(s) that is to be modified must first be selected. A selected object is indicated by surrounding it with a box; a deselected object has no surrounding box.
Editors Display Window User Functions, Continued Sizing Graphic Objects l Multiple graphic objects can be selected by constructing a bounding box in the display window. If you press a mouse button in an open area of the display window (i.e.
Editors Display Window User Functions, Continued Moving Graphic Objects A graphic object’s location in the display window can be changed by using the mouse. If you press a mouse button while the mouse is over an object and drag the mouse without releasing the mouse button, then a bounding box will be shown. When the mouse button is released, the object’s position is changed to the location of the bounding box.
Editors Property Sheet The Property Sheet is a “floating” (non-modal) dialog that presents all the settable properties of the currently selected graphic object. The properties of a graphic object are specific to an object’s type. The properties are presented in a scrollable list, with the name and value of each property listed. See Graphic Objects on page 205 for a description of the graphic objects provided with the Graphic Editor. Continued on next page 200 890 USE 152 00 V.
Editors Property Sheet, Continued Lookup Dialog 890 USE 152 00 V.2 For each of the graphic objects provided with the Graphic Editor, a property editor is provided for its “address” property. This property editor not only allows you to directly enter the address of a Quantum/Premium register (or Concept/PL7 variable name), but also provides access to the “Lookup Dialog.
Editors Security You are protected from unauthorized access to your PLC data in three ways: 202 l The HTML page containing the Graphic Editor applet has been placed in a “secure” directory on the web module, then the Web browser user is asked for a password before being allowed to download the HTML page. l You must enter the correct password via the “Password Dialog” to have permission to save/delete files or send data values to the connected PLC.
Editors Applet Parameters Overview The Graphic Editor supports two applet parameters to customize its behavior. Applet parameters are specified with tags within the
Editors Applet Parameters, Continued Example The following is an example of an applet tag for the Graphic Editor that will cause it to startup in view mode and automatically load the graphics file named “UNIT_1”. The Web browser user would be allowed to send values to the PLC via any graphic objects that support sending values, if they have entered the write-access password.
Editors Graphic Objects Overview The set of graphic objects provided in the Graphic Editor is intended to support building graphic displays that mimic conventional instrument panels. All of the data monitoring and control objects have built-in communication capabilities, and are designed as stand-alone graphic objects. Additionally, to support customers that want to put several simple applets on a single HTML page, each object in the Graphic Editor set is provided in an applet version.
Editors Graphic Objects, Continued Horizontal Indicator, Continued Minimum EU Value The minimum value, in engineering units, of the direct address or variable Maximum PLC The maximum raw (unscaled) value of the direct address or See Note 3 Value variable in the PLC Minimum PLC The minimum raw (unscaled) value of the direct address or See Note 3 Value variable in the PLC Value Visible Indicates whether a digital display of the scaled value is to be shown Value Font The font for the digital display of
Editors Graphic Objects, Continued Vertical Indicator A Vertical Indicator provides an analog representation of the value of a variable or direct address in a PLC by drawing a vertical bar whose length is proportional to the value as a percentage of its range in engineering units.
Editors Graphic Objects, Continued Vertical Indicator, Continued High Limit Value The value in engineering units for the ‘High’ limit High Limit Color The color for the indicator bar when scaled value is greater than the ‘High’ limit Low Limit Value The value in engineering units for the ‘Low’ limit Low Limit Color The color for the indicator bar when scaled value is less than the ‘Low’ limit Low Low Limit Value The value in engineering units for the ‘Low Low’ limit Low Low Limit Color The col
Editors Graphic Objects, Continued Horizontal or Vertical Slider, Continued Minor Scale Divisions The number of minor (unlabeled) scale divisions Scale Color The color for the scale and its labels Scale Font The font for scale labels 0 to 100 Scale Precision The number of fractional digits to be shown for scale labels (Set to -1 to use a general exponential format.
Editors Graphic Objects, Continued Horizontal or Vertical Selector, Continued Digital Indicator Label Color The color for the label Label Font The font for the label Scale Visible Indicates whether a “scale,” labeled with the choices, is to be shown Scale Color The color for the scale and its labels Scale Font The font for scale labels Border Width The width (in pixels) for the graphic object’s border Border Color The color for the graphic object’s border 0 to 32 A Digital Indicator provi
Editors Graphic Objects, Continued Digital Indicator, Continued Maximum EU Value The maximum value, in engineering units, of the direct address or variable Minimum EU Value The minimum value, in engineering units, of the direct address or variable Maximum PLC Value The maximum raw (unscaled) value of the direct address or variable in the PLC See Note 3 Minimum PLC Value The minimum raw (unscaled) value of the direct address or variable in the PLC See Note 3 High High Limit Value The value in en
Editors Graphic Objects, Continued Message Display Push Button A Message Display shows a text message based on the value of a variable or direct address in a PLC. For each specified message, a value is also specified that will trigger its display.
Editors Graphic Objects, Continued Push Button, Continued Analog Meter Button Label The text label for the button Button Background The color for the button Button Label Color The color for the button label Button Label Font The font for the button label Border Width The width (in pixels) for the graphic object’s border Border Color The color for the graphic object’s border 0 to 32 An Analog Meter provides an analog representation of the value of a variable or direct address in a PLC by dra
Editors Graphic Objects, Continued Analog Meter, Continued Maximum EU Value The maximum value, in engineering units, of the direct address or variable Minimum EU Value The minimum value, in engineering units, of the direct address or variable Maximum PLC Value The maximum raw (unscaled) value of the direct address or variable in the PLC See Note 3 Minimum PLC Value The minimum raw (unscaled) value of the direct address or variable in the PLC See Note 3 Dial Degrees Sweep The amount of a circula
Editors Graphic Objects, Continued Rotary Slider A Rotary Slider provides an analog representation of the value of a variable or direct address in a PLC by drawing a knob on a circular dial whose position is proportional to the value as a percentage of its range in engineering units. The size of the circular dial (degrees sweep of a circle) and knob color can be set. With a mouse, a user can change the position of the knob and cause a new value to be sent to the PLC.
Editors Graphic Objects, Continued Rotary Selector A Rotary Selector allows a user to make a selection from a set of choices. When a selection is made, the value corresponding to the choice is sent to the PLC. The choices are shown as labels of a “scale,” with the current selection indicated by the position of the knob. The size of the circular dial (degrees sweep of a circle) and knob color can be set.
Editors Graphic Objects, Continued Trend Recorder A Trend Recorder provides a continuous, time-based charting of the value of a variable or direct address in a PLC. A Trend Recorder emulates a strip-chart recorder, with the pen on the right, and the “paper” moving from right to left. A vertical scale can be shown on the left side of the chart for showing the range of the value being recorded, and a horizontal scale can be shown below the chart for showing the time span of the chart.
Editors Graphic Objects, Continued Trend Recorder, Continued Minimum PLC Value The minimum raw (unscaled) value of the direct address or variable in the PLC See Note 3 Update Period The update interval (in seconds) for the chart 0.
Editors Graphic Objects, Continued NOTES 890 USE 152 00 V.2 1. If the Address property of a graphic object is a direct address, the Data Type property must be specified and cannot be set to UNDEFINED. If the Address property is a variable name, the Data Type property does not have to be specified and can be set to UNDEFINED. If, however, the Data Type property is specified for a variable, it must exactly match the variable’s actual data type. 2.
Editors 220 890 USE 152 00 V.
Alarm Viewer 8 At a Glance In This Section This section contains the following topics: For This Topic... See Page... Display 222 Limitations 227 Purpose The Alarm Viewer is a Java applet designed to monitor Premium PLCs. It is not currently supported by Quantum. It is a Client Runtime Function and will run in the JVM of internet client browser (Internet Explorer, Netscape Navigator, etc.). References Refer to the following manuals for a full explanation of the software.
Alarm Viewer Display Select Server | Alarm Viewer. Note: “Alarm Viewer” is a “Plug-in” You must download it before you can use it. The display is composed of: Button bar 1. Button bar (in the work area), 2. List of alarms, 3. Status frame. The button bar contains five buttons: This button is used to acknowledge a selected alarm in the list. A request is sent to the PLC (Diagnostic Buffer). This button is used to acknowledge all alarms in the list that can be acknowledged.
Alarm Viewer Display, Continued List of alarms Alarms in the list are displayed in historical order. The last alarm in runtime is added to the end of the list. Continued on next page 890 USE 152 00 V.
Alarm Viewer Display, Continued Each line displayed in the list corresponds to an alarm and contains the following information: Type: An icon that represents the alarm type. For each type there is a different icon: DFB alarm Grafcet alarm System alarm A-SI alarm Ack: An icon that represents the acknowledgement status. This alarm must be acknowledged by the user. Alarm has been acknowledged. Alarm doesn’t need to be acknowledged. Message: Alarm text. Appearance: Date and time when alarm occurs.
Alarm Viewer Display, Continued Zone or area number: Area or geographical zone from which the error comes (common area : 0). Note: l l l You can change the column width by using the mouse. The number of alarms that can be displayed in the list is limited to 1000. When this limit is reached, a warning message is displayed in the status frame. Alarm Viewer displays alarms from all zones. The zone contains values from 0 ... 15.
Alarm Viewer Operation and Management of Alarms Browsing Use the “Up”, “Down”, “PageUp”, or “PageDown” keys or the mouse to select (highlight) the alarms in the list. Use the scroll bar if the list contains more alarms than can be displayed in the dialog. Acknowledgment To acknowledge an alarm that requires acknowledgment, select the alarm and use the appropriate toolbar button. Several alarms can be acknowledged at one time by using the “Ack All” button.
Alarm Viewer Limitations For each alarm, there is additional information stocked in the diagnostic buffer. For example, many DFBs have outputs named STATUS (word) where the error cause is coded. Alarm Viewer doesn’t use this information. It displays only basic information about alarms. The Alarm Viewer will only work with the TSX ETY 110 WS hardware. It needs at least Premium PLC TSX57/PCX57/PMX57 V3.3 and PL-7 PRO or PL-7 Junior Version V3.3. 890 USE 152 00 V.
Alarm Viewer 228 890 USE 152 00 V.
Browser Requirements, Settings and Security Considerations A At a Glance Purpose In order to view the Java applets on FactoryCast Web sites, you must have the correct browser version. This appendix discusses that requirement and other browser considerations. In This Appendix This appendix contains the following topics: For This Topic... 890 USE 152 00 V.2 See Page...
Browser Requirements, Settings and Security Considerations Browser Version Overview In order to view the Java applets in the FactoryCast Web pages, you must have a browser which supports the Java Development Kit (JDK) 1.1.5. Which Browsers Qualify? The browsers that meet that requirement are: l Netscape Navigator 4.06 and Netscape Communicator 4.5 and higher l Internet Explorer 4.
Browser Requirements, Settings and Security Considerations Browser Settings Overview If you are using Microsoft Internet Explorer and you have trouble viewing Java applets, you can modify your browser security settings to improve your ability to view the applets. Procedure Follow the steps in the table below to modify the security settings of the browser: Step Action 1 Open Internet Explorer. 2 Select View | Internet Options from the menu bar. Result: The Internet Options window appears.
Browser Requirements, Settings and Security Considerations Browser Settings, Continued Procedure, Continued Step Action 3 Select the Security tab. Result: The Security dialog appears. 4 Select the Custom button in the security level settings section. Continued on next page 232 890 USE 152 00 V.
Browser Requirements, Settings and Security Considerations Browser Settings, Continued Procedure, Continued Step Action 5 Select the Settings button. Result: The Security Settings dialog appears. Continued on next page 890 USE 152 00 V.
Browser Requirements, Settings and Security Considerations Browser Settings, Continued Procedure, Continued Step Action 6 Select the Java Custom Settings button. Result: The Internet Zone dialog appears. 234 7 Select the Edit Permissions tab. 8 Under the Run Unsigned Content, select Enable. 9 Click OK. 890 USE 152 00 V.
Browser Requirements, Settings and Security Considerations Browser Security Considerations Security Issue Both Netscape Navigator and Internet Explorer remember a user name and password once entered for a Web site. We Recommend Close the browser after each session to prevent unauthorized people from using your passwords to gain read or write access to your site. If you are using Internet Explorer, you may also have to change your security settings using the custom settings option.
Browser Requirements, Settings and Security Considerations 236 890 USE 152 00 V.
Performance Benchmarks B At a Glance Purpose In This Appendix This appendix contains performance benchmarks for: l The Premium Embedded Server l The Quantum Embedded Server l The FactoryCast Configurator This appendix contains the following topics: For This Topic... 890 USE 152 00 V.2 See Page...
Performance Benchmarks Premium Performance Benchmarks Overview This section contains performance information for the TSX ETY 110 WS V2.2 Web Embedded Server compared with the TSX ETY 110 V2.2 Ethernet Module. All the response time are in ms. The client and the server have the same cycle time. Average time of 1 EF READ-VAR of 50 words ETHWAY TSXETY 110 V2.
Performance Benchmarks Premium Performance Benchmarks, Continued Average time of 8 EF READ-VAR of 50 words ETHWAY TSXETY 110 V2.2 Cyclic 10 50 221 229 247 TSXETY 110 WS installed 223 229 247 TSXETY 110 WS running with data editor 224 231 249 TSXETY 110 WS running with sysdiag on ETY client 236 240 254 TSXETY 110 WS running with sysdiag on ETY client and server 246 252 275 Cyclic 10 50 TSXETY 110 V2.
Performance Benchmarks Premium Performance Benchmarks, Continued Throughput time of Bridge ETHWAY TSXETY 110 V2.2 Cyclic 10 20 50 55 56 55 26 TSXETY 110 WS running 51 51 47 18 TSXETY 110 WS running with Comm ETY Bridge 61 58 58 56 TSXETY 110 WS running with Comm ETY client and server Bridge 62 63 62 23 Cyclic 10 20 50 57 57 60 31 TCP/IP TSXETY 110 V2.
Performance Benchmarks Quantum Performance Benchmarks Overview These Quantum Web Embedded Server performance tests were run on Win95 on a Dell OptiPlex Gxi at 200 MHZ. The PLC was a Quantum 424. Performance Data The following table contains the performance data for the Quantum Web Embedded Server. Web Scanner w/MSTR Block 50 scans 100 scans 200 scans 500 scans Web scanner loaded, 1 MSTR 48.2ms 33.4ms 134.3ms 34.3ms 34.3ms Web scanner loaded, 2 MSTR 43.7ms 66.4ms 45.6ms 43.8ms 46.
Performance Benchmarks Configuration Tool Performance Benchmarks Overview This section provides test results for downloading a namespace and for downloading a Web site. Application Download In this performance test, the Download Namespace Only option was chosen. Web Site Download 242 Trial ETY Embedded Server (min:sec) NOE Embedded Server (min:sec) 1 :20 :05 2 :20 :18 3 :20 :11 In this test, 10 HTML files of 2 K each were downloaded to the server.
B AC Index A Alarm Viewer 221 Alarm Viewer Display 222 Operation and Management of Alarms 226 Analog I/O diagnostics 74 B Browser Version 30, 56, 229 C Company logo 94 Configuration Tool Overview 15 System requirements 17 Controller status 34, 60 Custom Web pages Protected 30, 56, 94, 157 Unprotected 30, 56, 158 Using Java applets 160 Configuration, new 89 D Data Editor 172 Data templates 178 Direct addresses 180 Write-enabled 181 890 USE 152 00 V.
Index F R FIP I/O diagnostics 65 Firewall 24 Register values Valid for Premium 110, 175 Valid for Quantum 111, 175 Remote I/O diagnostics 38 H Home page, custom 155 I IP address 96 J Java applets Using on custom pages 160 Viewing 229 N O Option module diagnostics 64 S Security 108, 235 Conflicts 115 Symbols 92, 93, 102, 108, 172, 179, 181 System requirements 17 V Variables 92, 93, 102, 108, 172, 179, 181 Namespace 102, 108, 110 Resynchronizing 119 Saving 118 W P Web site Security 21 Write acc
31001229 Schneider Electric GmbH Steinheimer Strasse 117 D-63500 Seligenstadt Tel: (49) 6182 81-2584 Fax: (49) 6182 81-2860 Schneider Electric S.A. 245, Route des Lucioles-BP147 F-06903 Sophia-Antipolis Cedex Tel: (33) 92 96 20 00 Fax: (33) 93 65 37 15 Modicon, Square D and Telemecanique are PLC brand names from Schneider.
