Technical information

2/11
Presentation,
description
Modicon M580 automation
platform
Modicon X80 NRP EIO drop optical repeaters,
ConneXium managed switches
Modicon X80 EIO drop optical repeaters (1)(2)
Presentation
BMXNRP0200/0201 optical ber repeaters are an alternative to the use of
ConneXium managed dual ring switches (DRS), for optical ber communications
over long distances, in Ethernet I/O (EIO) systems.
When inserted in Modicon X80 RIO drops, BMXNRP0200/0201 optical ber
repeaters make it possible to:
b Extend the total distance of the EIO network, when EIO drops are located in
areas of the factory more than 100 m/328.084 ft away
b Enhance immunity to noise
b Resolve difference of potential between distant sites
b NRP repeaters can be installed on the primary ring or on secondary rings. These
modules cannot, however, be used to connect secondary rings to the primary ring
b The BMXNRP0200 repeater for multimode optical ber allows remote location up
to 2 km/1.243 mi.
The BMXNRP0201 repeater or single mode optical ber allows remote location up to
16 km/9.942 mi.
Depending on the conguration, the NRP repeater may be linked to the CRA adapter
of the drop where it is installed, via one or two Ethernet Interlink cables.
Description
1 Module reference
2 Display block indicating the module status
3 RJ45 Ethernet ports. Two LEDs, LNK and ACT, indicate the status of each port
4 Optical ber ports with SFP transceiver for LC type connector
ConneXium managed switches (3)
Presentation
There are three ConneXium managed DRS (Dual Ring Switch) models available
specically for EIO architectures. They are used in the following situations:
b For remote racks located at a distance of more than 100 m/328.084 ft
b Use of optical ber media:
v For remote racks located over long distances: 2 km/1.243 mi (multimode optical
ber) or 16 km/9.942 mi (single mode optical ber)
v In environments subject to interference
v Between sites with different earth equipotentiality
b Architectures with combined EIO and Ethernet DIO devices
b Implementation of a secondary ring
ConneXium managed switches specic to the medium
ConneXium
managed switch
Copper port Multimode
optical ber port
Single mode
optical ber port
Distance
between
switches
RJ45 shielded
connectors
Duplex SC connectors
TCSESM083F23F1
1 : 8 x 10/100
BASE-TX ports
– – 100 m/
328.084 ft
TCSESM063F2CU1
3 : 6 x 10/100
BASE-TX ports
2 : 2 x 10/100
BASE-FX ports
– 2 km/
1.243 mi
TCSESM063F2CS1
3 : 6 x 10/100
BASE-TX ports
–
2 : 2 x 10/100
BASE-FX ports
16 km/
9.942 mi
Predened conguration les
For ease of implementation of the 3 switches described above, 15 predened
conguration les are available for building validated and tested architectures.
These conguration les are included, as standard, on the Unity Pro V8.0 DVD.
The parameters of the switch(es) present on the Ethernet network can then easily
be easily set with the chosen conguration using a PC equipped with a web browser
or Ethernet Switch Congurator software. The switch is congured immediately.
Ethernet Switch Congurator software is also available on the ConneXium
Resource CD-ROM.
(1) For additional characteristics, see our website www.schneider-electric.com.
(2) Requires Unity Pro Extra Large software u V8.0.
(3) The functions described are only available for the three ConneXium managed switches
mentioned on this page: (TCSESM083F23F1/063F2CU1/063F2CS1).
3
2
TCSESM063F2CU1
TCSESM063F2CS1
1
TCSESM083F23F1
BMXNRP020p
2
3
4
1
Processors:
page 1/18
Software:
page 4/2
Ruggedized Modicon M580
modules: page 5/2
2
1
3
4
5
6
7
8
9
10
2
1
3
4
5
6
7
8
9
10