Use and Care Guide

ManualsBrandsSchluter Systems ManualsBathroomKerdi-Drain Grate 4-in Br Classic Gold Pure

INNOVATIVE SOLUTIONS FOR CERAMIC AND STONE TILE

FLOOR DRAINS FOR BONDED WATERPROOF MEMBRANES

Schluter

-KERDI-DRAIN and Schluter

KERDI-LINE floor drains provide a

simple and secure connection to bonded

waterproof membranes at the top of the

assembly via an integrated bonding flange.

Thus, the membrane is applied entirely at

the surface, with all water directed into the

top of the drain.

Application and Function

Schluter

-KERDI-DRAIN and Schluter

-KERDI-

LINE are specifically designed for use in

bonded waterproofing assemblies, such as

showers, steam rooms, wet rooms, bathroom

floors, commercial kitchen floors and other

applications that require waterproofing and

drainage.

8.2 Schluter

-KERDI-DRAIN is a floor drain

specifically designed to allow connections

to Schluter

-KERDI or other load-bearing,

bonded waterproof membranes. The

membrane is adhered to the large integrated

bonding flange to form a waterproof

connection at the top of the drain assembly.

KERDI-DRAIN consists of a drain casing and

fully adjustable grate assembly or covering

support to which tile is applied. The grate

assembly accommodates a wide range of

tile thicknesses and allows lateral and tilt

adjustment as well. The covering support is

placed flush with the top of the bonding flange

and can therefore accommodate any thickness

tile covering.

The standard KERDI-DRAIN is attached

directly to the waste line. The drain casing

is available in ABS, PVC, or stainless

steel. The plastic drain casings feature a

fleece-covered bonding flange. They are

available with standard 2" (50 mm) and

3" (75 mm) outlets and attached to the pipe

using an appropriate solvent cement. The

stainless steel drain casings are available with

standard 2" (50 mm) and 3" (75 mm) no-hub

outlets and 2" (50 mm) threaded outlet. The

no-hub outlets are attached to the pipe using

an appropriate mechanical (e.g., flexible or

no-hub) coupling. The threaded outlets are

attached to the pipe using thread sealing

compound or tape. The simple connection to

standard drain outlets makes KERDI-DRAIN

suitable for new construction and renovation.

The KERDI-DRAIN adaptor kit is designed

to convert clamping ring drains by equipping

them with an integrated bonding flange. The

adaptor kit includes a stainless steel adaptor

ring with an over-molded rubber gasket and

a variety of perforated hole patterns that align

with most common clamping ring shower

drains. The adaptor ring replaces the clamping

ring and is attached to the drain body using the

clamping ring bolts. This connection is made

watertight via the rubber gasket and Schluter

KERDI-FIX adhesive/sealant. The integrated

bonding flange slides into the adaptor ring,

with the over-molded rubber gasket ensuring

a watertight seal. KERDI-DRAIN ADAPTOR

KITS, available in 5-1/4" (133 mm) and 7-1/2"

(191 mm) diameter sizes, are used to convert

traditional clamping ring drains to integrated

bonding flange drains when removal of the

clamping ring drain is not practical (e.g., when

they are set in concrete slabs). Adaptor kits

are suitable for both mortar beds and KERDI-

SHOWER-T/-TS/-TT shower tray applications.

The KERDI-DRAIN grate assembly consists

of a frame, which can be seamlessly adjusted

to the thickness and layout of the ceramic tile

or stone covering via the height adjustment

FLOOR DRAINS

8.2 Schluter

-KERDI-DRAIN

4-23/32" - 120 mm

2-1/4" -

57 mm

7/8" -

22 mm

7/8" -

22 mm

15/16" - 24 mm

5-15/32" - 137 mm

2-1/4" -

57 mm

7/8" -

22 mm

7/8" -

22 mm

15/16" - 24 mm

Intermediate placement

Wall placement

8.7 Schluter

-KERDI-LINE

Summary of content (24 pages)

PAGE 1
F L OOR DR AI N S INNOVATIVE SOLUTIONS FOR CERAMIC AND STONE TILE FLOOR DRAINS FOR BONDED WATERPROOF MEMBRANES Schluter®-KERDI-DRAIN and Schluter®KERDI-LINE floor drains provide a simple and secure connection to bonded waterproof membranes at the top of the assembly via an integrated bonding flange. Thus, the membrane is applied entirely at the surface, with all water directed into the top of the drain.
PAGE 2
FLOOR DRAINS collar and lateral adjustment ring, and grates or cleanout covers that are placed within the frame. The 4" (100 mm) standard grate assembly frame features an approximately 1/8" (3 mm) wide reveal after installation and grate/ frame combinations are available in stainless steel with plain, chrome, nickel, classic gold, vintage gold, rose gold, or oil-rubbed bronze finish and anodized aluminum with brushed nickel, brushed copper, or brushed brass finish.
PAGE 3
FLOOR DRAINS Metallic-coated grates are stainless steel 304 with a metallic coating created using physical vapor deposition (PVD). The resulting metallic film is very hard and corrosion-resistant. Textured color-coated grates are stainless steel with a powder coat. Anodized aluminum grates feature an anodized layer that retains a uniform appearance during normal use. The surface may be damaged by grout or setting material. Therefore, these materials must be removed immediately.
PAGE 4
FLOOR DRAINS 3. Embed a 20" x 20" (50 x 50 cm) cut section of KERDI in the bond coat and work the membrane onto the KERDIDRAIN bonding flange and surrounding membrane to ensure full coverage and remove air pockets. The KERDI is carried to the step in the bonding flange (template provided) and must overlap the DITRA or DITRA-XL membrane by a minimum of 2" (50 mm). Grate assembly Grate 1. The grate assembly is installed in conjunction with the tile.
PAGE 5
FLOOR DRAINS 5 mm) V-notched trowel or the DITRATROWEL, which features an 11/64" x 11/64" (4.5 x 4.5 mm) square-notched design. Solidly embed the matting into the bond coat using a float, screed trowel, or DITRA-ROLLER. 2. Apply Schluter SET®, Schluter ALL-SET®, Schluter FAST-SET® or unmodified thinset mortar to the membrane surrounding KERDI-LINE with a 1/4" x 3/16" (6 x 5 mm) V-notched trowel or the KERDI-TROWEL, which features a 1/8" x 1/8" (3 x 3 mm) square-notched design.
PAGE 6
FLOOR DRAINS Product Item Numbers 8.
PAGE 7
FLOOR DRAINS Schluter®-KERDI-DRAIN ABS or PVC FLANGE — 2" or 3" OUTLET 2" (50 mm) drain outlet Material 3" (75 mm) drain outlet Item No. Material Item No.
PAGE 8
FLOOR DRAINS Schluter®-KERDI-DRAIN STAINLESS STEEL FLANGE — 2" or 3" OUTLET 2" (50 mm) drain outlet 3" (75 mm) drain outlet Material Item No. Material Item No. KD2 FLK E KD3 FLK E No-hub No-hub KD2 FLK ETH Threaded Additional components included 4x Inside corners 2x Outside corners 1x 1x Pipe seal (3/4" - 20 mm) Mixing valve seal (4-1/2" - 114 mm) 1x KERDI-FIX sealing and bonding compound (3.
PAGE 9
FLOOR DRAINS Schluter®-KERDI-DRAIN-H ABS or PVC FLANGE — 2" OUTLET HORIZONTAL 2" (50 mm) drain outlet Material Item No. KDH2 FLK ABS ABS KDH2 FLK PVC PVC Additional components included 4x 2x Inside corners 1x 1x Pipe seal (3/4" - 20 mm) Outside corners Mixing valve seal (4-1/2" - 114 mm) Flange measurements ABS or PVC 2" (50 mm) horizontal drain outlet A B D C E F A 11-13/16" - 300 mm B 4-21/32" - 118.3 mm C 2-47/64" - 69.5 mm D 2-3/8" - 60.5 mm E 3-3/8" - 85.
PAGE 10
FLOOR DRAINS Schluter®-KERDI-DRAIN-A ADAPTOR KIT — 5-1/4" or 7-1/2" ADAPTOR RING Schluter®-KERDI-DRAIN ADAPTOR KITS are used to convert traditional clamping ring drains to integrated bonding flange drains when removal of the clamping ring drain is not practical. A stainless steel adaptor ring with an overmolded rubber gasket replaces the clamping ring and is sealed to the existing drain body using Schluter®-KERDI-FIX.
PAGE 11
FLOOR DRAINS Schluter®-KERDI-DRAIN GRATES FOR USE WITH FLANGES WITH 2" OUTLET 4" (100 mm) Grate ® W! Schluter -KERDI-DRAIN-STYLE NE Pure U.S. Patent No. D831,795 Brushed stainless steel Brushed nickel Brushed rose gold Brushed vintage gold Item No. Item No. Item No. Item No. Brushed classic gold Item No. KDIF4 GRK EB D8 KDIF4 GRK EBT D8 KDIF4 GRK EBRG D8 KDIF4 GRK EBVG D8 KDIF4 GRK EBCG D8 Matte black Cream Greige Stone grey Bronze Matte white Item No. Item No. Item No. Item No.
PAGE 12
FLOOR DRAINS Stainless steel Stainless steel Chrome Oil-rubbed bronze Item No. Item No. Item No. KD4 GRK E KD4 GRK EP KD4 GRK EOB Nickel Rose gold Vintage gold Classic gold Item No. Item No. Item No. Item No. KD4 GRK ET KD4 GRK ERG KD4 GRK EVG KD4 GRK ECG Anodized aluminum Brushed nickel anodized aluminum Brushed copper anodized aluminum Brushed brass anodized aluminum Item No. Item No. Item No.
PAGE 13
FLOOR DRAINS Schluter®-KERDI-DRAIN GRATES FOR USE WITH FLANGES WITH 2" OUTLET 4" (100 mm) Grate Tileable grate Tileable grate Item No. KD4 GRK ECS Patent pending Contents 1x 1x Spacer Tileable covering support GRATES FOR USE WITH FLANGES WITH 2" or 3" OUTLET 6" (150 mm) Grate Stainless steel Stainless steel - 6" square Stainless steel - 6" round Item No. Item No.
PAGE 14
FLOOR DRAINS Schluter®-KERDI-DRAIN DRAIN KITS — ABS or PVC FLANGE - 2" OUTLET - STAINLESS STEEL GRATE Schluter®-KERDI-DRAIN ABS - 2" (50 mm) PVC - 2" (50 mm) 4" (100 mm) square grate Stainless steel KD2/ABS/E KD2/PVC/E Contents 1x 1x Flange Grate and frame 4x Inside corners 2x Outside corners 1x Height adjustment collar 1x Pipe seal (3/4" - 20 mm) 1x Lateral adjustment ring 1x Mixing valve seal (4-1/2" - 114 mm) ADAPTOR KIT — 5-1/4" ADAPTOR RING - 4" STAINLESS STEEL GRATE 5-1/4" (133.
PAGE 15
FLOOR DRAINS Schluter®-KERDI-DRAIN ABS or PVC FLANGE — 2" or 3" OUTLET - WITHOUT SEALS AND CORNERS 2" (50 mm) drain outlet Material 3" (75 mm) drain outlet Item No. Material Item No. KD2/ABS/FL KD3/ABS/FL ABS ABS KD2/PVC/FL KD3/PVC/FL PVC PVC HORIZONTAL ABS or PVC FLANGE — 2" OUTLET - WITHOUT SEALS AND CORNERS 2" (50 mm) drain outlet Material Item No.
PAGE 16
FLOOR DRAINS Schluter®-KERDI-DRAIN 10 PACKS — ABS OR PVC FLANGE - 2" OUTLET 2" (50 mm) drain outlet Additional components included Material Item No. 40x Inside corners KD2 FLK ABS 10 20x Outside corners ABS 10x Pipe seal (3/4" - 20 mm) KD2 FLK PVC 10 10x Mixing valve seal (4-1/2" - 114 mm) PVC Note: 10 packs are packaged in bulk, not individually boxed. 10 PACKS — ABS FLANGE - 5-1/4" ADAPTOR RING 5-1/4" (133.4 mm) adaptor ring Additional components included Flange and ring Item No.
PAGE 17
FLOOR DRAINS Schluter®-KERDI-DRAIN 6" SQUARE CLEAN OUT COVER The Schluter®-KERDI-DRAIN Clean Out Cover is a 6” stainless steel cover available for installations where the KERDIDRAIN bonding flange is to be used in a cleanout application. Clean out cover 6" Item No. Finish KD-GR6C-E Stainless steel TAMPER PROOF SCREWS Schluter ®-KERDI-DRAIN Tamper Proof Screws are designed as a high security accessory for the KERDI-DRAIN.
PAGE 18
FLOOR DRAINS Note: There are multiple selections to be made for this product. Begin by selecting the appropriate channel body length then proceed to grate selection accordingly, keeping in mind there two frame height options for the perforated and closeddesign grates.
PAGE 19
FLOOR DRAINS Schluter®-KERDI-LINE GRATE ASSEMBLY - BRUSHED STAINLESS STEEL CONTENTS 1x 1x Grate 6 design options: • Closed-design • Perforated • Frameless tileable • Curve • Floral • Pure Closed (A) 3/8" 10 mm Grate frame with height adjustment spacers. See product tables for frame height options (not included with frameless tileable grate).
PAGE 20
FLOOR DRAINS Schluter®-KERDI-LINE GRATE ASSEMBLY - CHROME Closed (A) 3/8" 10 mm 1-27/32" 47 mm Perforated (B) 3/8" 10 mm 2-1/8" - 54 mm =H =H 2-29/32" - 74 mm 2-29/32" - 74 mm Grate assemblies - Chrome 3/4" (19 mm) frame height for 1/8" to 9/16" (3 mm to 15 mm) -thick coverings Length = in. - cm 19-11/16 23-5/8 27-9/16 31-1/2 35-7/16 39-3/8 43-5/16 47-1/4 - 50 - 60 - 70 - 80 - 90 - 100 - 110 - 120 Frameless Tileable (D) Closed (A) Perforated (B) Item No.
PAGE 21
FLOOR DRAINS Schluter®-KERDI-LINE-STYLE GRATE ASSEMBLY - BRUSHED STAINLESS STEEL STYLE DESIGNS 2-29/32" (74 mm) Curve Floral 4 2-29/32" (74 mm) 4 =H Pure 2-29/32" (74 mm) =H 2-1/8" (54 mm) 2-1/8" (54 mm) 2-1/8" (54 mm) Grate assemblies - Brushed stainless steel 29/32" - 23 mm frame height for 1/4" - 11/16" (6 - 18 mm) -thick coverings Length = in. - cm 19-11/16 23-5/8 27-9/16 31-1/2 35-7/16 39-3/8 43-5/16 47-1/4 - 50 - 60 - 70 - 80 - 90 - 100 - 110 - 120 Curve1 Floral2 Pure3 Item No.
PAGE 22
FLOOR DRAINS Schluter®-KERDI-LINE PERFORATED GRATE WITH LOCKING MECHANISM The Schluter®-KERDI-LINE perforated grate assembly (B) with 3/4" (19 mm) frame height is available with a locking mechanism for applications where tamper resistance is required. Perforated grate assembly with locking mechanism Length = in. - cm 19-11/16 23-5/8 27-9/16 31-1/2 35-7/16 39-3/8 43-5/16 47-1/4 51-3/16 55-1/8 59-1/16 62-15/16 66-7/8 70-13/16 Item No.
PAGE 23
FLOOR DRAINS Product Listings and Certifications Table Schluter®-KERDI-DRAIN - Listings and Certifications Grate - 4" (100 mm) Grates Flanges Design 1 Stainless steel (All finishes except EOB) Design 1 Design 2 Stainless steel Anodized aluminum (All finishes) EOB Grate - 6" (150 mm) Tileable STYLE - Pure, Curve and Floral Stainless steel Stainless steel (All finishes) Square 6E Round 6RE Cover 6CE 2" PVC 1 - 1 1 1 1 1 2 2" ABS 1 - 1 1 1 1 1 2 2" PVC Horizontal 1 - 1 1 1
PAGE 24
Schluter®-Systems Floor Drains 10-Year Limited Warranty COVERAGE AND CONDITIONS: Subject to the conditions and limitations as stated hereinafter, Schluter®-Systems* warrants that Schluter®-KERDI-DRAIN or Schluter®KERDI-LINE (the “Product”) will be free from manufacturing defects, and will not rot, deteriorate or break down under normal use for a period of ten (10) years from the date of purchase only when the Product is used and installed in accordance with the terms and conditions of the Schluter-Systems F