Use and Care Guide

WALL AND COUNTERTOP PROFILES
6
Product Item Numbers
H = 1/4" - 1/2"
(6 - 12.5 mm)
1/8" - 3 mm
R = Radius
Notes:
• Radius available for JOLLY in
metal profiles only.
• JOLLY in polished aluminum
and chrome-plated brass
require a relatively large
bending radius.
Note: Additional finishes are available for this product.
The design configuration of JOLLY is identical to that of
SCHIENE (see Floor Profiles). However, their materials
and finishes do vary. SCHIENE, in all materials and
finishes, is suitable for floor applications, as well as wall
and countertop applications. JOLLY is suited primarily for
walls and countertops. However, JOLLY in AM, AMGB,
AK, AKGB, AT, ATGB, ABGB and ACGB is also suitable
for floors and may be used in such applications to increase
design options.
H = 1/8"- 3/16"
(3 - 4.5 mm)
2.3 Schluter
®
-JOLLY
H =
mm - in.
Item No.
Chrome-
plated
solid
brass
(MC)
Polished
chrome
anodized
aluminum
(ACG)
Brushed
chrome
anodized
aluminum
(ACGB)
Satin
nickel
anodized
aluminum
(AT)
Polished
nickel
anodized
aluminum
(ATG)
Brushed
nickel
anodized
aluminum
(ATGB)
6 - 1/4 MC 60 A 60 ACG A 60 ACGB A 60 AT A 60 ATG A 60 ATGB
8 - 5/16 MC 80 A 80 ACG A 80 ACGB A 80 AT A 80 ATG A 80 ATGB
10 - 3/8 MC 100 A 100 ACG A 100 ACGB A 100 AT A 100 ATG A 100 ATGB
12.5 - 1/2 MC 125 A 125 ACG A 125 ACGB A 125 AT A 125 ATG A 125 ATGB
H =
mm - in.
Item No.
Satin
copper
anodized
aluminum
(AK)
Polished
copper
anodized
aluminum
(AKG)
Brushed
copper
anodized
aluminum
(AKGB)
Brushed
antique bronze
anodized
aluminum
(ABGB)
Satin
brass
anodized
aluminum
(AM)
Polished
brass
anodized
aluminum
(AMG)
6 - 1/4 A 60 AK A 60 AKG A 60 AKGB A 60 ABGB A 60 AM A 60 AMG
8 - 5/16 A 80 AK A 80 AKG A 80 AKGB A 80 ABGB A 80 AM A 80 AMG
10 - 3/8 A 100 AK A 100 AKG A 100 AKGB A 100 ABGB A 100 AM A 100 AMG
12.5 - 1/2 A 125 AK A 125 AKG A 125 AKGB A 125 ABGB A 125 AM A 125 AMG
H =
mm - in.
Item No.
Brushed
brass
anodized
aluminum
(AMGB)
Bright
black
anodized
aluminum
(AGSG)
Brushed
graphite
anodized
aluminum
(AGRB)
4.5 - 3/16 - A 45 AGSG -
6 - 1/4 A 60 AMGB A 60 AGSG A 60 AGRB
8 - 5/16 A 80 AMGB A 80 AGSG A 80 AGRB
10 - 3/8 A 100 AMGB A 100 AGSG A 100 AGRB
12.5 - 1/2 A 125 AMGB A 125 AGSG A 125 AGRB
3. Set the adjacent row of tiles. Leave a space
of approximately 1/16" – 1/8" (1.5 – 3 mm)
between the profile and the tile.
4. To set tile along the face of QUADEC-
FS, apply thin-set mortar to the back of
the tile using a margin trowel. Press the
back-buttered tiles into the face of the
profile, making sure to force thin-set mortar
fully into the dovetailed grooves. The tiled
surface should be flush with the outer edge
of the profile. Note: The recessed face
accepts tile widths up to 2" (51 mm).
5. Fill joints completely with grout or setting
material.
6. Work with materials and tools that will
not scratch or damage sensitive surfaces.
Setting materials must be removed
immediately.
Note: Matching inside corners/outside corners/
end caps are available.
Corners/end caps are held in place with thin-set
mortar. Fill the ends of the profile with thin-set
mortar prior to inserting the accessories.
DESIGNLINE
1. DESIGNLINE may be used with tiles that are
1/4" (6 mm) thick or greater.
2. Set tiles up to the area where DESIGNLINE
is to be installed as a decorative strip. Apply
a sufficient amount of thin-set mortar to this
area and/or to the back of DESIGNLINE
and press the profile into the mortar until its
surface is flush with the tile.
3. Set the adjacent row of tiles.
4. Set the tile to the integrated joint spacer,
which ensures a uniform joint of 1/16" -
1/8" (1.5 - 3 mm). With the stainless steel
and solid brass profiles, leave a space of
approximately 1/16" - 1/8" (1.5 - 3 mm).
5. Fill joints completely with grout or setting
material.
REMA
1. Adhere an aluminum bracket to the back of
each perimeter tile with thin-set mortar so
that the magnet extends beyond the tile’s
edge.
2. Set tiles, with magnets attached, as
perimeter limits, so that four magnets
extend into the access opening.
3. To form the access panel cover, connect
the corresponding number of panel cover
tiles by attaching a tile to their backs with
thin-set mortar.
4. Using KERDI-FIX, silicone, or a similar
adhesive, adhere the counterplates to the
back of the panel cover in alignment with
the perimeter magnets.
5. After the adhesive has cured, install the cover
and seal the surrounding joint with a color-
coordinated sealing compound. Note: If the
access opening is substantially larger than
12" x 12" (30 x 30 cm), it may be necessary
to install two additional magnets.
Maintenance
Schluter
®
wall and countertop profiles require no
special maintenance or care and are resistant to
mold and fungi. Clean profiles using common
household cleaning agents.
Stainless steel surfaces exposed to the
environment or aggressive substances should
be cleaned periodically using a mild household
cleaner. Regular cleaning maintains the neat
appearance of stainless steel and reduces the
risk of corrosion. All cleaning agents must be
free of hydro-chloric, hydrofluoric acid, and
chlorides. Stainless steel surfaces develop a
sheen when treated with a chrome-polishing
agent.
Oxidation films on solid brass or aluminum
may be removed with a common polishing
agent, but will form again.
In the case of chrome-plated brass, anodized
aluminum, color-coated aluminum, and
textured color-coated aluminum do not use
abrasive cleaning agents.