Operation Manual

 www.scheppach.com /  [e-mail] /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• Look for discoloration on the top of the spark plug.
By default, the color should be bright.
• Check the spark plug gap. An acceptable gap
width is 0.6 to 0.7 mm (Fig. 15)
• Remove the spark plug carefully by hand.
• If the plug has been inserted, tighten them with a
spark plug wrench.
• Attach the spark plug wire with connector on the
spark plug.
Note
A loose spark plug can overheat and damage the en-
gine. And overtightening the spark plug can damage
the threads in the cylinder head.
Cleaning
• Keep all safety devices, air vents and the motor
housing free of dirt and dust. Wipe the equipment
with a clean cloth or clean it with compressed air
at low pressure.
• We recommend that you clean your device after
each use.
• Clean the unit regularly with a damp cloth and
some soft soap. Do not use cleaning agents or
solvents; they may damage the plastic parts of the
appliance. Make sure that no water can get inside
the unit.
10. Storage
1. Perform all general maintenance, which are in
the User’s Guide in the Maintenance section.
2. Let the fuel out of the tank (Use a commercially
plastic fuel pump from the hardware store).
3. After the fuel is drained, start the machine.
4. Let the machine in idlespeed running until it
stops. That cleans the carburetor from the re-
maining fuel.
5. Let the machine cool down. (about 5 minutes)
6. Remove the spark plug.
7. Fill a small amount of 2-stroke engine oil into the
ring chamber. Pull out several times the starter
cord gently to wet the internal components with
the oil.
8. Replace the spark plug.
9. Clean the outer casing of the machine.
10. Keep the machine on a cold, dry place out of
reach of ignition sources and ammable sub-
stances.
Recommissioning
1. Remove the spark plug.
2. Pull the starter rope out several times. It cleans
the ring chamber of oil residues.
3. Clean the spark plug contacts or install a new
spark plug.
4. Fill the tank.
11. Transport
m WARNING
Let the engine cool down before transporting the ma-
chine or storing indoors to avoid burns or re hazards.
If you want to transport the unit empty the fuel tank
before. Clean the unit with a brush or a broom of
coarse dirt.
8.5 Operating display (15)
Power indicator active - when the engine is running.
8.6 Energy saving switch (9)
Reduce fuel consumption / idle - Energy saving
switch „ON“ position.
9. Maintenance
m WARNING
• Carry out maintenance work only with the stopped
engine.
• Pull the spark plug cap from the spark plug
Oil change
The engine oil change should take place when the
engine is at operating temperature.
• When changing the oil, have a non-leaking con-
tainer available.
• Remove the engine cover (Fig. 6-7 Pos. 5)
• Open the oil ller plug (Fig. 9 Pos. D)
• Drain the old oil into a suitable container by tilting
the generator.
• Fill the engine oil to the upper mark of the dipstick
using the oil-lling container.
• Dispose of the oil in accordance with stipulations.
Take the old oil to a collection point. Most petrol
stations, garages or recycling centres take back old
oil free of charge.
Air lter
The air lter is equipped with two air lter inserts.
Frequently cleaning of the air lter prevents carbure-
tor malfunction.
Clean the air lter and change air lter inserts
• The air lter should be cleaned every 30 hours.
• Remove the engine cover (Fig. 6 - 7 Pos. 5)
• Remove the air lter cover (Fig. 10 Pos. E)
• Remove the lter elements (Fig. 11 Pos. F+G)
• Clean the lter elements with soapy water. After
rinse the lter elements with clear water and allow
to dry thoroughly before retting.
• Reassemble in reverse order
m WARNING
NEVER use gasoline or cleaning solvents with a low
ash point to clean the air lter element. A re or ex-
plosion could result.
Note
Never run the engine without or with a damaged air
lter. Dirt gets so into the engine, causing serious
engine damage can occur. In this case, seller, and
manufacturer disassociate from any warranty.
Check, clean and replace spark plug
Check the spark plug after 10 hours on dirt and grime.
If necessary, clean it with a copper wire brush. Main-
tenance the spark plug after 50 hours of operation
• Open the spark plug cover (Fig. 12 + 13)
• Remove the ignition cable with plug. (Fig. 14 Pos.
D)
• Remove any dirt from the base of the spark plug.
• Use a wrench to remove the spark plug.
• Check the spark plug visually. Remove any debris
with a wire brush.
GB
FR
CZ
SK
DE
22 / 56