Operation Manual

19
Montage de l’aspiration, Fig. 5
Monterleraccordd’aspiration(4Fig.1)surlamachineà
l’aidedesvisàtêtefendueetdesrondelles(4aet4b)
Ensuite montez la tôle de protection (4c) avec le
boulon (4a et 4d). Faites attention à ce que la
tôle touche le bord inférieur de la table à poncer.
Si vous inclinez la table, il faut ajuster la hauteur de la
tôledeprotection.
Montage des pieds en caoutchouc, Fig. 6
Monterles4piedsencaoutchouc(1aFig.1)surlapla-
que de fondation
Attention ! Si,pendantletravail,lamachineatendancea
sedéplacerouàbasculer,elledoitêtrexéesurlasur-
facedetravailàl’aidedequatrevis(noncomprisesdans
l’étenduedelafourniture).
Utilisation comme machine stationnaire
Silaponceuseàbande/disquedoitêtreutiliséedansun
endroitdénitif,xezlaàunétabliouàuneautresurface
stable.Lorsquevousmontezla ponceuse surunétabli,
percezdestrousdanslasurfacesupérieuredel’établi.
• Faites des repères sur l’établipour les trous quiper-
mettrontdexervotreponceuse.Utilisezlestrousdela
basedevotreponceusecommegabaritpourladisposi-
tion des trous.
• Percezlestrousdansl’établi.
• Placezlaponceusesurl’établi,enalignantlestrousde
sabaseaveclestrouspercésdansl’établi.
• Insérez les boulons (non inclus)et serrezles bien en
utilisant des rondellesfreins et des écrous hex. (non
inclus).Note:Touslesboulonsdoiventêtreinséréspar
ledessus.Montezlesrondellesfreinsetlesécrousen
dessousdel’établi.
Utilisation comme machine mobile
Silaponceuseàbande/disquedoitêtretransportéepour
êtreutiliséeàdifférentsendroits,nousvousrecomman-
donsdelaxerdemanièrepermanentesurunpanneau
demontagequipeutêtrefacilementxéàunétabliouà
touteautresurface à l’aidedeserrejoints. Le panneau
demontagedoitêtre sufsamment grand pouréviter le
basculementdelaponceuselorsdesonutilisation.Nous
vous recommandons d’employer un morceau de contre
plaquéoud’agglomérédebonnequalitéde19mm(3/4
po)d’épaisseur.
Mounting the vacuum connector Fig. 5
Mountthevacuumconnector(4Fig.1)tothemachineus-
ingtheslottedscrewsandwashers(4aand4b).
Nextttheguard(4c)usingthebolt(4aand4d).Makesure
the guard reaches onto the lower edge of the sanding table.
If the sanding table is inclined, the guard must be adjusted
for height.
Mounting the rubber feet Fig. 6
Mountthe4rubberfeet(1aFig.1)tothebaseplate
ATTENTION!Ifthemachinehasatendencytomoveortilt
duringoperation,itmustberestrainedintheworkspace
byfourscrews(notprovided).
Operation as stationary machine
Ifyourbelt/discsanderistobeusedinapermanentloca-
tion, it is recommended you secure it to a workbench or
otherstablesurface.Whenmountingthebelt/discsander
toaworkbench,holesshouldbedrilledthroughthesup-
portingsurfaceoftheworkbench.
• Markholesonworkbenchwherebelt/discsanderisto
bemountedusingholesinthebaseasatemplatefor
holepattern.
• Drillholesthroughworkbench.
• Placebelt/discsanderonworkbenchaligningholesin
the base with holes drilled in the workbench.
• Insert bolts (not included) and tighten securely with
lockwashersandhexnuts(notincluded).
Note: All bolts should be inserted from the top. Install
the lock washers and hex nuts from the underside of the
workbench.
Operation as mobile machine
Ifyourbelt/discsanderistobeusedasaportabletool,it
isrecommendedyoufastenitpermanentlytoamounting
boardthatcaneasilybeclampedtoaworkbenchorother
stablesurface.Themountingboardshouldbeofsufcient
sizetoavoidtippingwhilebelt/discsanderisinuse.Any
goodgradeplywoodorchipboardwitha3/4in.(19mm)
thickness is recommended.