Owner’s Manual 8-inch Wheel 1/2 Horsepower (continuous duty) 2000 R.P.M. to 3450 R.P.M. (no load speed) 8-INCH VARIABLE SPEED BENCH GRINDER Model No. 1010053 CAUTION: FOR YOUR OWN SAFETY; Read and follow all of the Safety and Operating Instructions before Operating this Bench Grinder Customer Helpline 1-800-266-9079 Please have your Model No. and Serial No. available. 37773.
TABLE OF CONTENTS SECTION PAGE Contact Information........................................................................................................................................................2 Product Specifications...................................................................................................................................................2 Safety Instructions ...................................................................................................................
SAFETY INSTRUCTIONS 8. DO NOT FORCE THE TOOL to perform an operation for which it was not designed. It will do a safer and higher quality job by only performing operations for which the tool was intended. GENERAL SAFETY INSTRUCTIONS Operating a Bench Grinder can be dangerous if safety and common sense are ignored. The operator must be familiar with the operation of the tool. Read this manual to understand this Bench Grinder.
22. EACH AND EVERY TIME, CHECK FOR DAMAGED PARTS PRIOR TO USING THE TOOL. Carefully check all guards to see that they operate properly, are not damaged, and perform their intended functions. Check for alignment, binding or breaking of moving parts. A guard or other part that is damaged should be immediately repaired or replaced.
GROUNDING INSTRUCTIONS USE ONLY A 3-WIRE EXTENSION CORD THAT HAS A 3-PRONG GROUNDING PLUG AND A 3-POLE RECEPTACLE THAT ACCEPTS THE TOOL’S PLUG. WARNING THIS TOOL MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRIC SHOCK. REPLACE A DAMAGED OR WORN CORD IMMEDIATELY. IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides the path of least resistance for electric current and reduces the risk of electric shock.
7. KEEP ALL WHEEL GUARDS IN PLACE. DO NOT USE THE BENCH GRINDER WITH THE WHEEL GUARDS REMOVED. SPECIFIC SAFETY INSTRUCTIONS FOR BENCH GRINDERS The operation of any grinder can result in debris being thrown into your eyes, which can result in severe eye damage. ALWAYS WEAR EYE PROTECTION. Any power tool can throw debris during operations, which could cause severe and permanent eye damage. Everyday eyeglasse are NOT safety glasses. ALWAYS wear Safety Goggles (that comply with ANSI standard Z87.
CARTON CONTENTS Fig. C D C B F E G H I J K L M O N UNPACKING AND CHECKING CONTENTS (Fig. C) The following items are to be provided in the shipping box: This Bench Grinder will require a minimal amount of assembly. A. Grinder (not shown) 1. Remove parts from all of the cartons and lay them on a clean work surface. C. Eyeshield assembly, right 2. Remove any protective materials and coatings from all of the parts and the bench grinder.
ASSEMBLY INSTRUCTIONS The Bench Grinder is provided with a left and right two piece Tool Rest. Right Tool Rest has a flat, smooth surface to lay your workpiece against. Left tool rest is used to sharpen twist drill bits. Fig. E WARNING I 1. DO NOT assemble the Bench Grinder until you are sure the tool IS NOT plugged in. 2. DO NOT assemble the Bench Grinder until you are sure the power switch is in the “OFF” position. 3.
SPARK ARRESTORS (Fig. F) WORK LIGHT 1. Assemble the Spark Arrestors (A) to the front surface of the Wheel Covers (B) with the flat washers and pan head screws (C) as shown. See Figure F. The Bench Grinder is provided with a Flexible Work Light to assist in visibility of the workpiece. WARNING 2. Adjust each Spark Arrestor until the lower edge (D) is 1/16" from the grinding wheel. Firmly tighten the hex head screws. See Figure F.
OPERATING THE BENCH GRINDER 7. To use the Drill Bit Sharpening tool rest, lay the drill bit flat in the “V” groove. Firmly hold on to the drill bit shank. Slide the drill bit towards the grinding wheel unit until it lightly touches. Keep the drill bit flat to the plate and rotate the drill bit. The Bench Grinder is designed for hand held grinding, sharpening, and cleaning operations. ALWAYS WEAR EYE PROTECTION! Hot sparks are produced during grinding operations.
USING THE WHEEL DRESSER (Fig. J) CHANGING THE GRINDING WHEEL (Fig. K) Fig. J Fig. K C H I G E B C A B Due to normal wear, both wheels will need to be replaced occasionally. 1. Turn the power switch OFF and unplug the power cord from its power source. The Wheel Dresser is to be used on the grinding wheels. It will remove buildup up of material on the grinding wheel, remove imperfections and make the corners of the grinding wheel square. See Figure J. 2.
5. Push a wood wedge between the grinding wheel and the guard. Then use a cresent wrench to remove the arbor hex nut. WIRE WHEEL or BUFFING WHEEL (Fig. L) Fig. L 6. NOTE: The left hand arbor hex nut is left hand threaded and is loosened by rotating it clockwise. The right hand arbor hex nut is right hand threaded and is loosened by rotating it counter-clockwise. B A 7. Remove the Outer Wheel Flange (H) and then the abrasive wheel (I) from the arbor shaft. C D 8.
MAINTENANCE OF THE BENCH GRINDER CAUTION: REPLACE the abrasive wheels if there is amy damage at all. FAILURE to replace a damaged wheel can cause serious injury to the operator. WARNING Turn the power switch “OFF” and unplug the power cord from its power source prior to any maintenance. CAUTION: DO NOT USE FLAMMABLE MATERIALS to clean the Bench Grinder. A clean dry rag or brush is all that is needed to remove dust and debris buildup.
8-IN. BENCH GRINDER PARTS LIST MODEL NO.
PARTS MODEL NO. 1010053 MODEL NO. M90083 8-IN. BENCH GRINDER PARTS LIST WARNING When servicing, use only Scheppach replacement parts. Use of any other parts may create a HAZARD or cause product damage. WARNING Any attempt to repair or replace electrical parts on this Grinder may create a HAZARD unless repair is done by a qualified service technician. Ref. No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 4-0.
LIMITED WARRANTY ONE-YEAR LIMITED WARRANTY. MODELS COVERED IN THIS MANUAL, ARE WARRANTED TO THE ORIGINAL USER AGAINST DEFECTS IN WORKMANSHIP OR MATERIALS UNDER NORMAL USE FOR ONE YEAR AFTER DATE OF PURCHASE. ANY PART WHICH IS DETERMINED TO BE DEFECTIVE IN MATERIAL OR WORKMANSHIP AND RETURNED SHIPPING COSTS PREPAID, WILL BE, AS THE EXCLUSIVE REMEDY, REPAIRED OR REPLACED AT OUR OPTION. FOR LIMITED WARRANTY CLAIM PROCEDURES, SEE “PROMPT DISPOSITION” BELOW.
