Technical data

www.schaerer.comTable of contents
Programming manual / V01 / 02.2010
5 / 62
Table of contents
Introduction ...............................................................4
Signs & Symbols ..................................................................... 4
Safety symbols ..................................................................................4
Remarks ............................................................................................4
Environment ......................................................................................4
About the software ...................................................7
Setting example for parameters ............................................. 7
Installation & Commissioning .................................8
Initial use .................................................................................. 8
Setup conditions ..................................................................... 8
Location ............................................................................................8
Climate ..............................................................................................8
Installation conditions ............................................................ 8
Power supply ....................................................................................9
Water connection / draining .............................................................10
Technical data........................................................................ 10
Initial start-up software .......................................... 11
Software dialogue ..................................................................11
Calibrate Touchscreen .................................................................... 11
Set language ...................................................................................11
Select operating mode ....................................................................12
Select machine type ........................................................................12
Machine information ........................................................................12
Congure grinders ..........................................................................13
Machine ll-up .................................................................................13
Machine ready for operation ...........................................................13
Programming: SERVICE card ................................14
Navigation in the programming level .................................. 14
Enter the programming level ................................................ 14
Overview programming SERVICE card ............................... 14
1. General parameters ............................................15
1.1. Temperature settings ................................................................15
1.2. Machine conguration ..............................................................15
1.3. Calibrate grinders ....................................................................17
1.4. Milk parameter .........................................................................18
1.5. Cleaning parameters ................................................................20
1.6. Machine information .................................................................21
1.7. Time / Date ..............................................................................21
1.8. Automatic timer ........................................................................22
1.9. Alarm functions ........................................................................22
2. Congure display ...............................................23
2.1. Button conguration ................................................................23
2.2. Set contrast .............................................................................23
2.3. Calibrate touchscreen .............................................................23
2.4. Display options .........................................................................24
3. Congure products ............................................25
3.1. Dene new product ..................................................................25
3.2. Delete product .........................................................................28
3.3. Set product parameters ...........................................................28
3.4. Enter product prices .................................................................29
3.5. Assign buttons ..........................................................................30
3.6. Assign external buttons ............................................................31
4. System test / calibration.....................................32
4.1. Input / output test .....................................................................32
4.2. Diagnosis screen ......................................................................32
4.3. Set pump pressure ...................................................................32
4.4. Move brew piston .....................................................................33
4.5. Calibrate grinders .....................................................................33
4.6. Grinding time adjustment .........................................................33
4.7. Grinder empty message ...........................................................34
4.8. Milk empty message ................................................................34
4.9. Functional test ..........................................................................34
4.10. Continuous test .....................................................................34
4.11. Drain system ..........................................................................35
5. Chip card service ................................................36
5.1. Erase card ................................................................................36
5.2. Change PIN code .....................................................................36
5.3. Simulate chip card ....................................................................36
5.4. Load counter from SAVE DATA ...............................................36
5.5. Load data from SAVE DATA .....................................................37
5.6. Save language on chip card .....................................................37
5.7. Congure CHEF card ...............................................................37
5.3.1 Simulate CHEF card ..................................................... 38
1. Free vend ....................................................................................38
2. View counters ..............................................................................38
3. Congure products ......................................................................38
4. Congure coffee blends ..............................................................39
5. Congure display ........................................................................39
6. Time / Date ..................................................................................39
7. Automatic timer ...........................................................................39
8. Language ....................................................................................40
9. Switch off machine ......................................................................40
10. Enable milk system ...................................................................40
5.3.2 Simulate PROGRAM card ............................................ 41
1. Enter product prices ....................................................................41
2. Load MONEY card ......................................................................41
3. Erase MONEY card .....................................................................41
4. Display sales ...............................................................................41
5. Change PIN code .......................................................................41
6. Payment system settings ............................................................42
5.3.3 Simulate ROASTER card ............................................. 43
1. View counters ..............................................................................43
2. Congure products ......................................................................43
3. Language ....................................................................................43
4. Set temperatures .........................................................................43
6. Congure interface .............................................44
6. Congure interface ......................................................................44
7. Payment system settings ...................................45
7.1. Set payment system .................................................................45
7.2. MONEY-card initialisation ........................................................45
7.3. Enter product prices .................................................................46
7.4. Display sales ............................................................................46
7.5. Log on MASTER card ..............................................................46
7.6. Delete table (MASTER) ............................................................46
7.7. Diagnosis .................................................................................46
8. Load factory settings .........................................48
9. View counters .....................................................49
9.1. Daily counter ............................................................................49
9.2. Monthly counter ........................................................................49
9.3. Machine counter total ...............................................................49
9.4. Service counter ........................................................................50
9.5. Cleaning statistics ....................................................................50
9.6. Error statistics ..........................................................................50
10. Software upgrade .............................................51
10. Software upgrade ......................................................................51
Special functions ....................................................52
Clear Flag (abort running cleaning cycle) ........................... 52
Chip cards ...............................................................53
SAVE DATA card .................................................................... 53
Functional description .....................................................................53