Security System User Guide
Contents 1. Introduction .................................................... 1 Controls and Displays.......................................... 3 Displays......................................................... 3 Controls:........................................................ 4 2. Everyday Operation ......................................... 5 Access to the System .......................................... 5 Entering and Leaving the Protected Area ............ 5 Setting....................................
1. Introduction The i-on16 is a wireless intruder alarm system intended mainly for use in domestic and small commercial properties. The heart of the i-on16 system is the control unit and its keypad. The control unit contains the main wireless receiver, the power supply and stand-by battery. The stand-by battery can keep the alarm system going for up to 12 hours if the mains supply fails. Connected to the control unit by cable is a keypad.
Introduction A B 1. Two button panic alarm. 2. Two button panic alarm with tilt switch. 3. Two button panic alarm A 1 2 abc 3 def B 4 ghi 5 jkl 6 mno C 7 pqrs 8 tuv 9 wxyz D * 0 # 4. Four button remote control. 5. Wireless arming station. 6. Door Contact/Universal Transmitter. 7. Smoke Detector. 8. Passive Infra Red. 9. External siren/strobe. Figure 1.
Introduction This rest of this guide shows the simple procedures required to operate and administer the system. For information on installing the i-on16 please read i-on16 Installation and Programming Guide. Each of the radio peripherals also have their own guides. Controls and Displays Figure 2 shows the controls and displays available on the keypad. 1 2 7 3 4 5 1. 2. 3. 4. LCD display . Programming keys. Navigation key Setting and unsetting keys.
Introduction The four LEDs on the right of the programming keys show you that the system is set or unset. The left hand LED glows when the system is full set, the second from left glows when the system is part set. Note that the installer can disable these LEDs in order to hide the state of the system. (The two right hand LEDs are never used.) Controls: A Full sets the system. B Part sets the system. Unsets the system. u In menus: scroll up. In text editing: move cursor left n In menus: scroll down.
2. Everyday Operation Everyday operation involves setting and unsetting the alarm system and occasionally dealing with alarms. If you need to know how to set up new users, or change the way the system operates then please read the “Administration” section. Access to the System To operate the system a user must identify themselves, either by entering an access code on the keypad or by presenting a proximity tag to the front of the keypad.
Everyday Operation Setting Note: Whenever you set the system you should first make sure that all doors and windows are secure. Full Set Make sure the system is idle. 1. EITHER: Key in your access code. OR Present a proximity tag to the keypad. The display shows: A : Full Set B : Part Set (The names for A and B may differ from that shown, depending on how the installer has set the system up.) 2. Press A. The display shows the number of seconds you have to left in which to leave the premises.
Everyday Operation At the end of the exit time the exit warning tone stops and you should hear a double “beep” confirmation tone to let you know that the system is set. The display shows the message "System Set" for a few seconds, followed by the standby screen. The left hand LED glows to show that the system is full set. System Set Notes: a) If you decide you want to stop setting then press . b) Your system may be programmed to set silently. If so, there will be no exit warning tone as the system sets.
Everyday Operation Quick Set Quick Setting does not require the use of an access code or tag. (The Installer must enable this facility for you.) Make sure the system is idle. 1. Press A. The keypad gives the exit warning tone. 2. Setting 10 to set Leave by the exit door and make sure it is closed properly. At the end of the exit time the display shows the message "System Set" for a few seconds. System set While the system is set the display shows the standby screen.
Everyday Operation If the System Will Not Set Normally, the system will set only when all the detectors are “quiet”, that is: not reporting any activity. (This does not apply to those detectors on your exit door or exit/entry route. The system expects these detectors to be active as you leave the protected area.) If you try to set when one or more detectors are still active then the display shows the words “SETTING FAULTS” and which zones are active.
Everyday Operation Setting With a Remote control Note: You must program the control unit to recognise ("learn") a remote control, see page 23. Secure all your windows and doors. Make sure the system is idle, and that you can hear the warning tones from the keypad. 1. Press the appropriate button on the remote control, either full set (A) or part set (B), see page 20. The keypad sounds the exit warning tone. 2. Leave by the exit door and make sure it is closed properly (if you have not already done so).
Everyday Operation Unsetting When unsetting the system do not stray from the entry route designated by the installer. If you do then you will cause an alarm. 1. Enter by the designated entry door. The control unit starts the entry tone. 2. EITHER Key in your access code. OR Present a prox tag to the keypad. The system unsets. The display shows: System Unset Followed by the standby screen. Unsetting With a Remote control 1. Enter by the designated entry door. 2. Press on your remote control.
3. Alarms Types of Alarm The i-on16 normally starts an alarm when it receives an alarm signal from one of its detectors. In addition, you can start a panic alarm from the keypad. The table below shows the different kinds of alarms possible. Type of Alarm Intruder Signal (see note) Started by: Loud warbling tone from siren. Normal alarm or entry route zone activated when system is set. Fire Repeated “Dee Dah” from siren. Fire zone activated at any time.
Alarms Silencing an Alarm In an alarm the i-on16 operates the siren. The siren runs for a limited time set by the installer (a maximum 15 minutes for intruder and PA alarms). If you return to the control unit after the siren has stopped and key in your access code then the red LEDs around the navigation keys glow to tell you that an alarm has occurred. Press > to see information about the alarm. (Press u or n to see the name of the zone.) Press Y to restore the display to normal.
4. Alerts (or Why is it Beeping?) From time to time the control unit may detect that there is a problem with the system. It will try to inform you of this by starting an alert. During an alert the rim of the navigation pad glows red, and the keypad will give an short “beep” every few minutes. To see the cause of the alert: 1. Make sure the system is unset and that the keypad display shows the standby screen. 2. Press Y . The display asks you to key in an access code. 3. Key in a user access code.
5. Administration To make changes to the way your system works you must enter the Menu. Your degree of access to the Menu depends on what type of user you are: Admin User or Normal User. An Admin User has access to all the options of the Menu. A Normal User: Can change their own access code. Cannot add or delete other users. Can turn the Chime feature on or off. Entering the Menu 1. Make sure the display shows the standby screen. 2. Press 3. Key in an access code. .
Administration Omit Zones You may wish to prevent a zone causing an alarm. For example, if you have a fire door that is normally closed and protected by a detector you may wish to leave it open for fresh air or to move goods in and out. To do this the control unit allows you to "Omit" a zone. 1. Enter the Menu and select Omit Zones. The bottom line of the display shows the first of a list of zones. 2. Press u or n to display the zone you wish to omit. 3. Press > to mark the zone for omission.
Administration 2. Press u or n to display the user you wish to edit, and then press >. The bottom line shows one of a list of the options that you can edit: Name Type Code Prox Tag Remotes Panic Alarm Use the u or n keys to scroll through the list. 3. Press > to select the option you wish to edit. (The options available are the same as those shown when adding a user.) 4. Press Y when you have finished. Name If you wish to edit the name displayed on the keypad for a user: 1.
Administration 1 4 ghi 2 abc 3 def ABCÆÅÄ DEF 5 jkl 6 mno GHI JKL MNOØÖ 7 pqrs 8 tuv 9 wxyz PQRS TUV * 0 WXYZ # Space'():.-!&@0 Figure 3. Letters Assigned to Keys 5. Press # to change between capitals and small letters. The cursor becomes an underline when you type in small letters and a block when you type in capitals. 6. Press Y when finished. User Types To change a user’s type select Users - Edit User - User(nn) - Type. 1.
Administration Proximity Tags A proximity tag is a small plastic token with a low powered radio transmitter inside. Each tag contains a unique identity code. Inside the keypad is a sensor. When you present the tag within about 10mm of the front of the keypad, the control unit senses the presence of the tag and reads its identity code.
Administration Remote controls A remote control is a transmitter that you can attach to a keyring. The remote control has four buttons and a small LED that glows when it transmits a signal. When delivered from the factory three of the buttons are dedicated to setting or unsetting the system (see Figure 4). 1. 2. 3. 4. 5. Full Set. Part Set. Not used. Unset. Transmit LED. A B Figure 4. Remote control Buttons. You may allocate one (and only one) remote control to each user.
Administration If the control unit has already learned that remote control then you will hear a low tone and the display tells you that the remote control is already in use. If you have a remote control and want to know who it belongs to then use the Test - Remotes menu option, see page 24 . PA (Panic Alarms) A PA is a two button transmitter, used to start a Panic Alarm. To activate the transmitter you must press both buttons at the same time.
Administration 1. Enter the Menu and select Users - Edit User. The bottom line of the display shows the first in a list of the users currently recognised by the system. 2. Press u or n to display the user whose device you wish to delete., the press >. The bottom line of the display shows “Name”. 3. Press u or n until the bottom line shows the device you wish to delete, then press >.
Administration 4. Key in the user code you want the new user to employ. Key it in a second time when prompted by the display. The display asks you to present a proximity tag to the keypad. 5. Present an unused tag to the keypad. If you do not want to assign one to the user press Y. The display then asks you to press a button on any remote control that you want to assign to the user. 6. Press a button on a remote control (one that is not currently registered to any other user).
Administration "forgets" the identity of all remote controls and PAs registered to the user. View Log The control unit keeps a log of the last 250 events (for example, alarms and setting/unsetting). To read the log: 1. Enter the menu and select View Log. The display shows you the most recent log event. 2. Press u or n to scroll through the log. n shows earlier events, u shows more recent events. 3. Press > to see a more detailed description of the event. 4. Press X to finish viewing the log.
Administration Siren Press > to turn the siren on and off again. The word "On" or "Off" on the display shows whether you should be hearing the siren. Keypad Press each key once. The display shows a character in response. Press both PA keys together to test. Press X to end the test. Walk test The display shows a list of all the detectors installed on the system. The top line of the display shows you how many detectors remain to be tested. Walk round and trigger each detector.
Administration System Configuration The System Configuration option allows you to set up parts of the system to suit your particular needs. If you need more extensive changes to the operation of the system then you must contact your installer. Make sure the system is idle. 1. Enter the Menu and select System Config. The bottom line of the display shows the first item of the System Configuration menu. 2. Press u or n to scroll through the options available, followed by > to gain access to an option.
Administration Set Date and Time You will need to re-program the date and time if the control unit looses power for an extended time, and the battery is exhausted. 1. Enter the System Config menu and select Set Time/Date. The top line of the display shows “Set the date” and the bottom line shows the current date in number format (day/month/year). The day is highlighted. 2. Key in the digits for the day/month/year. Press Y when you have finished.
Administration Note: Do not make the loudspeaker so quiet that you cannot hear the exit warning tone. Speech Phone Book Note: This option appears only if you have the I-SD01 speech dialler fitted. If you need to re-direct speech messages to new telephone numbers then: 1. Enter the Menu and select System Config - Speech Phone Book. The bottom line of the display shows “Tel No 1”. 2. Press u or n to scroll through the available telephone numbers, followed by > to gain access to an individual number.
List of Menu Options Item Omit Zones (Zone 01, 02, …) Users Edit User (for each user:) Name Type Code Prox Tag Remotes Panic Alarm Add User Delete User View Log Test Siren Keypad Walk test Remotes Panic Alarms Prox Tags System Config Facilities On/Off Chime Set Date & Time Loudspeaker Speech Phone Book Page 16 18 16 17 18 16 19 20 21 22 23 24 24 25 25 25 25 25 25 26 26 27 27 28 Page 29
© Cooper Security Ltd. 2008 Every effort has been made to ensure that the contents of this book are correct. However, neither the authors nor Cooper Security Limited accept any liability for loss or damage caused or alleged to be caused directly or indirectly by this book. The contents of this book are subject to change without notice. Printed and published in the U.
