User’s Manual VEGA V-1010 Linear Imager Handheld Bar code Scanner
EMEA SCANTECH-ID BV Nijverheidsweg Noord 60-34 3812 PM Amersfoort The Netherlands Tel:+31-33-4698400 Fax:+31-33-4650615 E-mail:info@scantech-id.com www.scantech-id.com HEAD QUARTER CHAMPTEK INCORPORATED 5/F, No.2 Alley 2, Shih-Wei Lane, Chung Cheng Rd., Hsin Tien City, Taipei 231,Taiwan Tel:+886-2-2219-2385 Fax:+886-2-2219-2387 E-mail:sales@champtek.com www.champtek.com China CHAMPTEK INCORPORATED #901, No. 39, Wuzhong Rd.
User’s Installation and Configuration Manual Scantech-ID VEGA
Copyright © 2009, Scantech-ID BV. This manual is copyrighted, with all rights reserved. Under the copyright laws, this manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic medium or machine readable form without prior written consent of Scantech-ID BV. Limited Warranty Under all circumstances this manual should be read attentively, before installing and/or using the product.
1 Table of contents Introduction .......................................... 6 Chapter 1 Product Safety ............................. 7 1.1 Safety & caution ......................... 8 1.2 FCC warning .............................. 9 Chapter 2 2.1 Chapter 3 3.1 Chapter 4 4.1 General Description ....................... 10 Use of the VEGA ......................... 11 Installation of the VEGA .................. 12 V-1010 Unpacking ........................ 13 Cover Display .............................
2 6.2.1 Interface ................................ 26 6.3 SCANNER operation ........................26 6.3.1 Reading Mode ............................. 26 6.3.2 Good Read LED Control .................... 27 6.3.3 Beeper Option ............................ 27 6.3.4 Reading Level ............................ 28 6.3.5 Accurany / Redundant Scan ................ 28 6.3.6 Sensitivity of Continuous Reading ........ 28 6.3.7 Reverse Output Characters ................ 29 6.4 RS232 mode parameters .
Scantech-ID VEGA Linear Imager 3 6.8.2 Supplemental Setup ........................ 43 6.8.3 Check Digit Transmission .................. 44 6.9 Code 39 parameters ...................... 45 6.9.1 Type of Code .............................. 45 6.9.2 Check Digit Transmission .................. 45 6.9.3 Output Start/Stop Character ............... 45 6.9.4 Decode Asterisk ........................... 46 6.9.5 Set Up Code Length ........................ 46 6.10 Code 128 parameters ..................
4 6.14.2 Transmission Type of Start/Stop .......... 59 6.14.3 Set Up Code Length ....................... 60 6.15 Code 93 parameters .......................62 6.15.1 Check Digit Transmission ................. 62 6.15.2 Set Up Code Length ....................... 62 6.16 Code 11 parameters .......................64 6.16.1 Check Digit Transmission ................. 64 6.16.2 Set Up Code Length ....................... 64 6.17 MSI/plessey code parameters ..............66 6.17.
Scantech-ID VEGA Linear Imager 7.1.2 5 User Define Code ID ....................... 75 7.2 preambles and postambles Insertion ...... 77 7.2.1 Setup Insertion ........................... 77 7.2.2 Insertion Set Number ...................... 78 7.2.3 Symbologies Selection ..................... 79 7.2.4 Character Position to be Insertion ........ 81 7.2.5 Characters to be Inserted ................. 81 7.3 Character deletion ...................... 82 7.3.1 Deletion Set Number ....................
6 Introduction VEGA is a cutting-edge gun-type barcode scanner which is designed specifically for retail market. To the brand new series of VEGA, we add on more user-friendly functions with detachable cable that makes it more easily to be operated by the customers. Speaking of the performance, this scanner supports middle to long range mode. For specification of VEGA which supports the reading depth up to 27 centimeter, scan rate is up to 700 scans / per second.
7 Chapter 1 Product Safety
8 Installation of the VEGA V-1010 1.1 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. SAFETY & CAUTION Please read the following safety statement carefully. Please preserve this user manual for reference sometime. Before cleaning the VEGA, the users must cut off all AC power. Do not use liquid or spray type of detersive to clean the VEGA. Please use dampish cotton cloth to clean the VEGA. The outlet must set nearby the VEGA for connecting power easily. Keep the VEGA dry to avoid short circuit.
Scantech-ID VEGA Linear Imager 1.2 9 FCC WARNING This equipment complies with the requirements in Part 15 of FCC. Any operation must comply with the conditions below: (a) The equipment will not cause any severe interference. (b) The equipment can avoid any interference from environment. Statement: This product is classified as B class product. In environment this product may cause some interference. In this situation the user may do something to avoid interference.
10 Installation of the VEGA V-1010 Chapter 2 General Description
Scantech-ID VEGA Linear Imager 2.1 11 USE OF THE VEGA THE VEGA IS VERY ERGONOMIC AND MODERN DESIGNED AND VERY USER FRIENDLY. IT CAN BE CONNECTED TO YOUR POS OR HOST SYSTEM TROUGH A RS232 CABLE, KBW CABLE, USB CABLE OR WITH BLUETOOTH WIRELESS. To read a bar code, you simply press the red trigger button and aim the beam to the bar code. But you need to position the beam so that it falls across all bars in the 1D barcodes.
12 Chapter 3 Installation of the VEGA
Scantech-ID VEGA Linear Imager 3.1 13 V-1010 UNPACKING Unpack the VEGA as follows: 1. Take the VEGA and its accessories out of the box. 2. Remove the packing material. 3. Check the packing list to make sure you have received all of the items ordered. Standard Shipment Package a. VEGA Linear Imager Handheld Bar code Scanner b. Communication Cable (RS-232 or Keyboard wedge or USB) c. Vega Stand d. User Manual e. Transparent Cover Plate 4.
14 Configuring the VEGA Chapter 4 Cover Display
Scantech-ID VEGA Linear Imager 4.1 15 SETUP COVER DISPLAY The VEGA scanner has the opportunity to change the decorative cover display on the top of the scanner into a display that can show our own commercial message. 4.1.
16 Configuring the VEGA 4.1.2 Change Cover Display Follow the next instruction steps to change the black Cover Display into the transparent Cover Display, so that your customers can read your own commercial massage. Step 1: Press out the front rubber lid toward the arrow. ➀ Step 2: Pull out the front rubber lid off the main unit. ➁ Step 3: Press out top cover rim from the inner lock.
Scantech-ID VEGA Linear Imager 17 Step 4: Press out the other side of inner lock and remove the complete cover. ➃ Step 5 Assemble transparent top cover rim into inner lock. ➄ Step 6 Assemble another side transparent top cover rim into the inner lock.
18 Configuring the VEGA Step 7 Insert your commercial message card into the top cover toward the arrow. ➆ Step 8 Assemble the front rubber lid into the main unit toward the arrow.
Scantech-ID VEGA Linear Imager Chapter 5 Configuring the VEGA 19
20 Configuring the VEGA 5.1 PREFACE How to configure the VEGA: The Barcode programming feature gives the possibility to change the VEGA scanner settings with use programming labels. 5.1.1 Changing Scanner Settings with Programming Codes You can set-up your VEGA by scan all necessary programming codes for parameters that meet applications. In order to change the scanner settings please follow the sequence below: 1. Power-up the scanner. 2.
Scantech-ID VEGA Linear Imager 21 5.1.2 Programming Flow Chart Start Configuration Recall Parameters Interface Selection Communication Parameters Bar codes Parameters Misc. Parameters etc.
22 Configuring the VEGA 5.
23 Chapter 6 Programming Codes
24 Miscellaneous Parameters 6.1 GENERAL PROCESS 1 Power up the Scanner 2 Scan the Start of Configuration bar code Scan the bar code for the desired feature. You can scan 3 all features before scanning End of Configuration. 4 Scan End of Configuration bar code 5 Scan Save Parameters bar code 6.1.1 Abort Configuration Terminate current programming status. 6.1.
Scantech-ID VEGA Linear Imager 6.1.3 Set All Default Set all the parameters to the factory default settings 6.1.
26 Miscellaneous Parameters 6.2 INTERFACE SELECTION 6.2.1 Interface RS232 Mode USB Mode 6.3 SCANNER OPERATION 6.3.
Scantech-ID VEGA Linear Imager Flash/Auto Power ON Testing 6.3.2 Good Read LED Control Good Read LED OFF 6.3.
28 Miscellaneous Parameters 6.3.4 Reading Level Bar Equals High 6.3.5 Accurany / Redundant Scan - Require 1 good decode for a good scan 1 Redundant Scan - Require 2 consecutive decodes of the same bar code data for a good scan 2 Redundant Scan - Require 3 consecutive decodes of the same bar code data for a good scan 3 Redundant Scan - Require 4 consecutive decodes of the same bar code data for a good scan 6.3.
Scantech-ID VEGA Linear Imager 6.3.7 Reverse Output Characters Example: 012345 543210 Enable 6.4 RS232 MODE PARAMETERS 6.4.
30 Miscellaneous Parameters 6.4.2 Data/Stop Bits The number of data bits transmitted for each character 7 Data Bits < 8 Data Bits > < 1 Stop Bits > 2 Stop Bits 6.4.3 Parity A Parity bit is an extra data bit used to help catch data transmission errors. Even – Select to set the parity bit either a 1 or 0 to ensure an even number of bits are 1’s Odd – Select to set the parity bit either a 1 or 0 to ensure an odd number of bits are 1’s Mark – Select to set the parity bit always 1.
Scantech-ID VEGA Linear Imager 6.4.4 Handshaking RTS/CTS ON – Output a Request to Send (RTS) signal and wait for a Clear to Send (CTS) signal before transmitting data RTS/CTS ACK/NAK – After transmitting data, wait for host to send an ACK or a NAK response. If ACK is received, then complete the data transmission. If NAK is received, re-send the last set of data and wait for ACK/NAK again. ACK/NAK XON/XOFF – After transmitting data, wait for host to send an XON or a XOFF response.
32 Miscellaneous Parameters 6.5 KEYBOARD WEDGE MODE PARAMETERS 6.5.
Scantech-ID VEGA Linear Imager 6.5.
34 Miscellaneous Parameters Portuguese Denmark Netherlands Turkey 6.5.3 Upper/Lower Case Enable Lower Case – Transmit all data as lower case Enable Upper Case – Transmit all data as upper case 6.5.
Scantech-ID VEGA Linear Imager 6.5.5 Character by ALT Method ALT Method Enable Send 6.5.
36 Miscellaneous Parameters 6.5.
Scantech-ID VEGA Linear Imager 6.6 OUTPUT CHARACTERS 6.6.
38 Miscellaneous Parameters 6.7 CODE TYPE 6.7.1 Barcode Selections If “Enable” is selected for all bar codes types, then the scanner could read all types of bar code. If “Disable” is selected for a certain bar code type, then the scanner could not read the particular bar code. The symbol of “<>” means default settings.
Scantech-ID VEGA Linear Imager CODE 39 CODE 39 OFF Standard Code 39 Full ASCII Code 39 ON Code32 / Italian Pharmacy ON Code32 / Italian Pharmacy Code 128 Code 128 OFF Interleave 2 of 5 Interleave 2 of 5 OFF Codabar/NW7 Codabar/NW7 OFF 39
40 Industrial 2 of 5 ON Industrial 2 of 5 Matrix 2 of 5 ON Matrix 2 of 5 CODE 93 ON CODE 93 CODE 11 ON CODE 11 MSI/PLESSEY ON MSI/PLESSEY Telepen ON Telepen Miscellaneous Parameters
Scantech-ID VEGA Linear Imager China Postage ON China Postage GS1 DataBar ON GS1 DataBar GS1 DataBar Expanded ON GS1 DataBar Expanded GS1 DataBar Limited ON GS1 DataBar Limited 41
42 Miscellaneous Parameters 6.8 UPC/EAN/JAN PARAMETERS 6.8.1 Reading Type UPC-A=EAN-13 ON Add 0 before UPC-A to make it 13 digits.
Scantech-ID VEGA Linear Imager EAN8=EAN13 Enable GTIN Format Enable 6.8.
44 Miscellaneous Parameters 6.8.
Scantech-ID VEGA Linear Imager 6.9 CODE 39 PARAMETERS 6.9.1 Type of Code Full ASCII Code 39 6.9.2 Check Digit Transmission Calculate Check Digit and Transmit Calculate Check Digit and Not Transmit 6.9.
46 Miscellaneous Parameters 6.9.4 Decode Asterisk Enable 6.9.5 Set Up Code Length To set the fixed length: (2 sets Available) 1. Scan the “Begin” programming code of the desired set 2. Go to the Decimal Value Tables in Appendix A, scan programming codes that represents the length to be read. 3. Scan the “Complete” programming code of the desired set. Repeat the steps 1 – 3 to set additional lengths.
Scantech-ID VEGA Linear Imager 47 Fixed Length 2nd Set 2nd Set Begin Decimal Value See Appendix A 2nd Set Complete Minimum Length Minimum Length Begin Decimal Value Minimum Length Complete See Appendix A
48 Miscellaneous Parameters 6.10 CODE 128 PARAMETERS 6.10.1 Reading Type UCC/EAN-128 Enable 6.10.2 Check Digit Transmission Do Not Calculate Check Digit Calculate Check Digit and Transmit 6.10.
Scantech-ID VEGA Linear Imager 6.10.4 49 Set Up Code Length To set the fixed length: (2 sets Available) 1. Scan the “Begin” programming code of the desired set 2. Go to the Decimal Value Tables in Appendix A, scan programming codes that represents the length to be read. 3. Scan the “Complete” programming code of the desired set.
50 Miscellaneous Parameters Minimum Length Minimum Length Begin Decimal Value Minimum Length Complete See Appendix A
Scantech-ID VEGA Linear Imager 6.11 INTERLEAVE 2 OF 5 PARAMETERS 6.11.1 Check Digit Transmission Calculate Check Digit and Transmit Calculate Check Digit and Not Transmit 6.11.2 Set Up Number of Character Odd 6.11.
52 Miscellaneous Parameters 6.11.4 Set Up Code Length To set the fixed length: (2 sets Available) 1 Scan the “Begin” programming code of the desired set 2 Go to the Decimal Value Tables in Appendix A, scan programming codes that represents the length to be read. 3 Scan the “Complete” programming code of the desired set.
Scantech-ID VEGA Linear Imager 53 Minimum Length Minimum Length Begin Decimal Value Minimum Length Complete See Appendix A
54 Miscellaneous Parameters 6.12 INDUSTRIAL 2 OF 5 PARAMETERS 6.12.1 Reading Type IATA25 Enable 6.12.
Scantech-ID VEGA Linear Imager 6.12.3 55 Set Up Code Length To set the fixed length: (2 sets Available) 1 1Scan the “Begin” programming code of the desired set 2 Go to the Decimal Value Tables in Appendix A, scan programming codes that represents the length to be read. 3 Scan the “Complete” programming code of the desired set.
56 Miscellaneous Parameters Minimum Length Minimum Length Begin Decimal Value Minimum Length Complete See Appendix A
Scantech-ID VEGA Linear Imager 6.13 57 MATRIX 2 OF 5 PARAMETERS 6.13.1 Check Digit Transmission Calculate Check Digit and Transmit Calculate Check Digit and Not Transmit 6.13.2 Set Up Code Length To set the fixed length: (2 sets Available) 1 Scan the “Begin” programming code of the desired set 2 Go to the Decimal Value Tables in Appendix A, scan programming codes that represents the length to be read. 3 Scan the “Complete” programming code of the desired set.
58 Miscellaneous Parameters Fixed Length 1st Set 1st Set Begin Decimal Value See Appendix A 1st Set Complete Fixed Length 2nd Set 2nd Set Begin Decimal Value See Appendix A 2nd Set Complete Minimum Length Minimum Length Begin Decimal Value Minimum Length Complete See Appendix A
Scantech-ID VEGA Linear Imager 6.14 CODABAR/NW7 PARAMETERS Set Up Start/Stop Characters upon Transmission 6.14.1 ON 6.14.
60 Miscellaneous Parameters C Start C Stop D Start D Stop 6.14.3 Set Up Code Length To set the fixed length: (2 sets Available) 1 Scan the “Begin” programming code of the desired set 2 Go to the Decimal Value Tables in Appendix A, scan programming codes that represents the length to be read. 3 Scan the “Complete” programming code of the desired set.
Scantech-ID VEGA Linear Imager 61 Fixed Length 1st Set 1st Set Begin Decimal Value See Appendix A 1st Set Complete Fixed Length 2nd Set 2nd Set Begin Decimal Value See Appendix A 2nd Set Complete Minimum Length Minimum Length Begin Decimal Value Minimum Length Complete See Appendix A
62 Miscellaneous Parameters 6.15 CODE 93 PARAMETERS 6.15.1 Check Digit Transmission Do Not Calculate Check Digit 6.15.2 Set Up Code Length To set the fixed length: (2 sets Available) 1 Scan the “Begin” programming code of the desired set 2 Go to the Decimal Value Tables in Appendix A, scan programming codes that represents the length to be read. 3 Scan the “Complete” programming code of the desired set. Repeat the steps 1 – 3 to set additional lengths.
Scantech-ID VEGA Linear Imager 63 Fixed Length 2nd Set 2nd Set Begin Decimal Value See Appendix A 2nd Set Complete Minimum Length Minimum Length Begin Decimal Value Minimum Length Complete See Appendix A
64 Miscellaneous Parameters 6.16 CODE 11 PARAMETERS 6.16.1 Check Digit Transmission Calculate Check 1 Digit and Transmit Calculate Check 1 Digit and Not Transmit Calculate Check 2 Digit and Transmit Calculate Check 2 Digit and Not Transmit 6.16.2 Set Up Code Length To set the fixed length: (2 sets Available) 1. Scan the “Begin” programming code of the desired set 2.
Scantech-ID VEGA Linear Imager 65 Fixed Length 1st Set 1st Set Begin Decimal Value See Appendix A 1st Set Complete Fixed Length 2nd Set 2nd Set Begin Decimal Value See Appendix A 2nd Set Complete Minimum Length Minimum Length Begin Decimal Value Minimum Length Complete See Appendix A
66 Miscellaneous Parameters 6.17 MSI/PLESSEY CODE PARAMETERS 6.17.1 Check Digit Transmission Calculate Check Digit and Transmit Calculate Check Digit and Not Transmit 6.17.2 Set Up Code Length To set the fixed length: (2 sets Available) 1. Scan the “Begin” programming code of the desired set 2. Go to the Decimal Value Tables in Appendix A, scan programming codes that represents the length to be read. 3. Scan the “Complete” programming code of the desired set.
Scantech-ID VEGA Linear Imager 67 Fixed Length 1st Set 1st Set Begin Decimal Value See Appendix A 1st Set Complete Fixed Length 2nd Set 2nd Set Begin Decimal Value See Appendix A 2nd Set Complete Minimum Length Minimum Length Begin Decimal Value Minimum Length Complete See Appendix A
68 Miscellaneous Parameters 6.18 TELEPEN PARAMETERS 6.18.1 Type of Code Telepen ASCII Telepen Numeric 6.18.2 Check Digit Transmission Do Not Calculate Check Digit Calculate Check Digit and Transmit 6.18.3 Set Up Code Length To set the fixed length: (2 sets Available) 4. Scan the “Begin” programming code of the desired set 5. Go to the Decimal Value Tables in Appendix A, scan programming codes that represents the length to be read. 6.
Scantech-ID VEGA Linear Imager 69 Fixed Length 1st Set 1st Set Begin Decimal Value See Appendix A 1st Set Complete Fixed Length 2nd Set 2nd Set Begin Decimal Value See Appendix A 2nd Set Complete Minimum Length Minimum Length Begin Decimal Value Minimum Length Complete See Appendix A
70 Miscellaneous Parameters 6.19 GS1 DATABAR PARAMETERS 6.19.1 Check Digit Transmission Calculate Check Digit and Not Transmit 6.19.2 Application ID Add 01 Before GS1 Databar Do Not Transmit Application ID 6.19.3 Symbology ID Transmit Symbology ID Add ]e0 Before GS1 Databar.
Scantech-ID VEGA Linear Imager 6.20 GS1 DATABAR LIMITED PARAMETERS 6.20.1 Check Digit Transmission Calculate Check Digit and Not Transmit 6.20.2 Application ID Add 01 Before GS1 Databar Limited. Don’t Transmit Application ID 6.20.3 Symbology ID Transmit Symbology ID Add ]e0 Before GS1 Databar Limited.
72 Miscellaneous Parameters 6.21 GS1 DATABAR EXPANDED PARAMETERS 6.21.1 Symbology ID Transmit Symbology ID Add ]e0 Before GS1 Databar Expanded.
Scantech-ID VEGA Linear Imager Chapter 7 Miscellaneous Parameters 73
74 Miscellaneous Parameters 7.1 BAR CODE ID 7.1.1 Default Barcode ID With this function on, a leading character will be added to the output string while scanning code; user may refer to the following table to know what kind of barcode is being scanned.
Scantech-ID VEGA Linear Imager 7.1.2 User Define Code ID To set the code ID 1. Scan the symbologies programming code. 2. Go to the ASCII Tables in Appendix B, Scan programming codes that represents the desired ID. Note: User defines code ID will override default value. Program will not check the conflict. It is possible to have more than two symbologies which have same code ID.
76 Industrial 2 of 5 Matrix 2 of 5 CODE 93 CODE 11 China Postage MSI/PLESSEY Telepen GS1 DataBar GS1 DataBar Expanded GS1 DataBar Limited Miscellaneous Parameters
Scantech-ID VEGA Linear Imager 7.2 77 PREAMBLES AND POSTAMBLES INSERTION 7.2.1 Setup Insertion To set the insertion of the output characters; 1. Scan the programming code of the desired set. 2. Scan the programming code of the desired symbology 3. Go to the Decimal Value in Appendix A, scan programming codes that represents the desired position to be inserted (1= the first digit, 99 the last digit). 4. Scan the “Complete” programming code of “Character Position to be Inserted”. 5.
78 Miscellaneous Parameters Complete $ Complete End of Configuration Bar Code Save Parameters Bar Code 7.2.
Scantech-ID VEGA Linear Imager 7.2.
80 CODE 11 China Postage MSI/PLESSEY Telepen GS1 DataBar RSS-14 GS1 DataBar Expanded GS1 DataBar Limited All Codes None Miscellaneous Parameters
Scantech-ID VEGA Linear Imager 81 7.2.4 Character Position to be Insertion Decimal Value See Appendix A Complete 7.2.
82 Miscellaneous Parameters 7.3 CHARACTER DELETION To setup the deletion of output characters: 1. Scan the programming code of the desired set. 2. Scan the programming code of the desired symbology. 3. Go to the decimal Value tables in Appendix A, scan programming codes that represents the desired position to be deleted. 4. Scan the “Complete” programming code of “Character Position to be Deleted”. 5.
Scantech-ID VEGA Linear Imager 3 – Delete 3 Characters Complete End of Configuration Bar Code Save Parameters Bar Code 7.3.
84 Miscellaneous Parameters 7.3.
Scantech-ID VEGA Linear Imager CODE 11 China Postage MSI/PLESSEY Telepen GS1 DataBar GS1 DataBar Expanded GS1 DataBar Limited All Codes None 85
86 Miscellaneous Parameters 7.3.3 Character Position to be Delete Decimal Value See Appendix A Complete 7.3.
Appendixes A. DECIMAL VALUE TABLE ..................... 88 B. ASCII TABLE ............................. 89 C. FUNCTION KEY TABLE ...................... 95 D. Readable Symbologies .................... 96 E. Technical Specifications ................ 97 F. Scan map ................................ 98 G. Test Symbologies ....................... 100 H. Overview Model Numbers .................
A.
Scantech-ID VEGA Linear Imager 89 B.
DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US SPACE ! ″ # $ % & ' ( )
Scantech-ID VEGA Linear Imager 91 * + , Comma minus .
@ A B C D E F G H I Letter I J K L M N O Letter O P Q R S T U
Scantech-ID VEGA Linear Imager 93 V W X Y Z [ \ ] ^ _ Underscore ` a b c d e f g h i j k
l m n o p q r s t u v w x y z { | Vertical slash } ~ DEL
Scantech-ID VEGA Linear Imager 95 C.
Up Down D.
Scantech-ID VEGA Linear Imager 97 E. TECHNICAL SPECIFICATIONS Physical Characteristics Scanner Scanner Weight (V-1010) Approx 240 gr. Material ABS Plastic Connector RJ 45C 10Pins Dimension 186.8 mm x 81.6 mm x 63.
6 7 8 9 10 11 8 cm 13 8.6 cm 14 0 2 3 4 34 17 81 0.5mm (70~270) 0.127mm (100~170) 0.25mm (80~200) 16 81 5 15 1cm 1 0.1mm (105~155) 12 1cm 5 2 4 3 3 4 2 5 1cm 18 81 19 20 21 26 27 28 F.
Scantech-ID VEGA Linear Imager 99 VEGA Typical Reading Distances (Centimetres) Symbology Density Minimum Distance Code 39 0.1 mm 0.127 mm 0.25 mm 0.5 mm 10.5 cm 10 cm 8 cm 7 cm Maximum Distance 15.5 cm 17 cm 20 cm 27 cm VEGA Typical Reading Distances (inches) Symbology Density Minimum Distance Code 39 4 mils 5 mils 10 mils 20 mils 4.1 3.9 3.2 2.8 inch inch inch inch Maximum Distance 6.1 inch 6.7 inch 7.9 inch 10.
G. TEST SYMBOLOGIES Scan one or more of these bar codes to test bar code symbologies you enabled.
Scantech-ID VEGA Linear Imager 101 Matrix 2 of 5 Industrial 2 of 5 UPC A UPC E 0 Telepen 12345 67890 5 0 1 23 456 China Postage 5
H. OVERVIEW MODEL NUMBERS VEGA with Linear Imager Version with RS232 interface: 1. A271002 VEGA V-1010-02 Version with KBW interface: 2. A271003 VEGA V-1010-03 Version with USB (HID KBW) interface: 3. A271004 VEGA V-1010-04 Version with USB (virtual com port) interface: 4.
Scantech-ID VEGA Linear Imager Quick Configuration Start Configuration
Scantech-ID BV Nijverheidsweg Noord 60-34 3812 PM Amersfoort The Netherlands Phone: +31 (0)33 469 84 00 Fax: +31 (0)33 465 06 15 E-mail: info@scantech-
