User`s manual

ManualsBrandsScantech ManualsBarcode ReaderVega V-1010

U s e r ’ s M a n u a l

VEGA Area Imager V-1020/V-1020BT

Handheld Bar code Scanner

Summary of content (138 pages)

PAGE 1
User’s Manual VEGA Area Imager V-1020/V-1020BT Handheld Bar code Scanner
PAGE 2
EMEA SCANTECH-ID BV Nijverheidsweg Noord 60-34 3812 PM Amersfoort The Netherlands Tel:+31-33-4698400 Fax:+31-33-4650615 E-mail:info@scantech-id.com www.scantech-id.com HEAD QUARTER CHAMPTEK INCORPORATED 5/F, No.2 Alley 2, Shih-Wei Lane, Chung Cheng Rd., Hsin Tien City,Taipei 231, Taiwan Tel:+886-2-2219-2385 Fax:+886-2-2219-2387 E-mail:sales@champtek.com www.champtek.com China CHAMPTEK INCORPORATED #901, No. 39, Wuzhong Rd.
PAGE 3
1 User’s Installation and Configuration Manual Scantech-ID VEGA
PAGE 4
2 Copyright © 2009, Scantech-ID BV. This manual is copyrighted, with all rights reserved. Under the copyright laws, this manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic medium or machine readable form without prior written consent of Scantech-ID BV. Limited Warranty Under all circumstances this manual should be read attentively, before installing and/or using the product.
PAGE 5
Scantech-ID Table of contents Table of Contents ...................................................................................... 3 Introduction................................................................................................ 7 Chapter 1............................................................................ Product Safety 9 1.1 Safety & Caution .............................................................................10 1.2 FCC Warning ......................................
PAGE 6
4 Chapter 6 .............................................................. Configuring the VEGA 31 6.1 Preface ........................................................................................... 32 6.2 Factory Default Setting ................................................................... 34 Chapter 7 ................................................................ Programming Codes 35 7.1 Return to Default............................................................................. 36 7.
PAGE 7
Scantech-ID 7.24 Matrix 2 of 5 Settings.......................................................................91 7.25 MaxiCode Settings ..........................................................................92 7.26 MicroPDF417 Settings.....................................................................93 7.27 MSI code Settings ...........................................................................94 7.28 PDF417 Settings ......................................................................
PAGE 8
6 Appendices ............................................................................................ 122 A Decimal Value Table .......................................................................... 123 B ASCII Table ....................................................................................... 124 C Readable Symbologies ...................................................................... 125 D Technical Specifications.....................................................................
PAGE 9
Scantech-ID Introduction VEGA is a cutting-edge gun-type barcode scanner which is designed specifically for retail market. To the brand new series of VEGA, we add on more user-friendly functions with detachable cable that makes it more easily to be operated by the customers. Speaking of the performance, this scanner supports middle to long range operation.
PAGE 10
8 Chapter 1 Product Safety
PAGE 11
Scantech-ID 1.1 SAFETY & CAUTION 1. Please read the following safety statement carefully. 2. Please preserve this user manual for reference sometime. 3. Before cleaning the VEGA, the users must cut off all AC power. Do not use liquid or spray type of detersive to clean the VEGA. Please use dampish cotton cloth to clean the VEGA. The outlet must set nearby the VEGA for connecting power easily. Keep the VEGA dry to avoid short circuit.
PAGE 12
10 General Description 1.2 FCC WARNING This equipment complies with the requirements in Part 15 of FCC. Any operation must comply with the conditions below: (a) The equipment will not cause any severe interference. (b) The equipment can avoid any interference from environment. Statement: This product is classified as A class product. In environment this product may cause some interference. In this situation the user may do something to avoid interference.
PAGE 13
Scantech-ID 1.3 SCANNER LABELLING Model Name Serial Number Model Name: VEGA V-1020 Area Imager VEGA V-1020BT Area Imager Bluetooth Serial Number: Product Serial No. (VA……..) See Appendix F for more information in detail.
PAGE 14
12 General Description Chapter 2 General Description
PAGE 15
Scantech-ID 2.1 USE OF THE VEGA The VEGA is very ergonomic and modern designed and very user friendly. It can be connected to your POS or Host system trough a RS232 cable, KBW cable, USB cable or with Bluetooth wireless. To read a bar code, you simply press the red trigger button and aim the beam to the bar code. But you need to position the beam so that it falls across all bars in the 1D barcodes. You will hear one beep and the green LED indicator will lights on after scan successfully.
PAGE 16
14 Chapter 3 Installation of the VEGA V-1020
PAGE 17
Scantech-ID 3.1 V-1020 UNPACKING Unpack the VEGA as follows: 1. Take the VEGA and its accessories out of the box. 2. Remove the packing material. 3. Check the packing list to make sure you have received all of the items ordered. Standard Shipment Package a. VEGA Area imager handheld bar code scanner b. Power Adaptor if apply c. User Manual d. Communication Cable e. Stand f. Transparent Cover Plate 4. Visually inspect the VEGA and accessories for any evidence of physical damage. 5.
PAGE 18
16 Installation of the VEGA V-1010 3.2 V-1020 MOUNTING Once you have unpacked all components, you can start installing the VEGA. Installing the VEGA is divided in different steps: 1. Connect the VEGA to the supplied communication cable (RJ45 side). 2. Connect the VEGA communication cable to the POS or Host system. 3. Connect the Power supply (if needed) to Power cable inlet. 4. Plug the power supply into the AC outlet.
PAGE 19
Scantech-ID 3.3 V-1020 USB DRIVER In case you will use the VEGA with USB virtual com port emulation, it is necessary to install the correct USB driver on your POS or Host system, needed for correct operation between your system and the VEGA scanner. You can download this USB driver from the Scantech-ID web site: www. Scantech-ID.
PAGE 20
18 Chapter 4 Installation of the VEGA V-1020BT
PAGE 21
Scantech-ID 4.1 V-1020BT UNPACKING Unpack the VEGA as follows: 1. Take the VEGA and its accessories out of the box. 2. Remove the packing material. 3. Check the packing list to make sure you have received all of the items ordered. Standard Shipment Package a. VEGA Area Imager Handheld Bar code Scanner Bluetooth b. Communication Cable (RS-232 or Keyboard wedge or USB) c. Power adaptor d. User Manual e. Bluetooth Cradle or charger(optional) f. Transparent Cover Plate 4.
PAGE 22
20 Configuring the VEGA 1. Connect the supplied communication cable at the bottom side of the cradle. 2. Connect the other side of the communication cable to the right connector of your POS or HOST system. 3. Plug the external power supply into the power jack on the bottom of the cradle. 4. Plug the power supply into the AC outlet. 5. Turn on your POS or HOST system. 6. Set up communication between the VEGA scanner and cradle.
PAGE 23
Scantech-ID 4.3.1 Pairing Pairing refers to when a VEGA scanner has been linked or paired to a specific cradle by scanning that cradle’s Bluetooth MAC address code, this Bluetooth MAC address code is unique for each cradle. This address code is located on the bottom side of the cradle. The pairing of a VEGA scanner to a cradle is one to one. Only one VEGA scanner can be paired to a cradle at any point in time. 4.3.
PAGE 24
22 Configuring the VEGA ATTENTION The VEGA scanner must be charged for a minimum of 8 hours before the scanner can be placed in full operation for the first time. The cradle red led will indicate in red when the scanner is charged. After the battery is full, The charge green light will be light. The charge green light will be off when the scanner leaving from cradle. If the battery power of the VEGA is too low, the VEGA will indicate this with red led and beeper warning.
PAGE 25
Scantech-ID 1. The VEGA scanner must scan “Scanner Server Mode ON/Scanner Client Mode Off” barcode, to set the VEGA scanner in server mode. 2. When control the Bluetooth device to search the scanner, enter pin code (default 00:00:00:00) to setup comport. 3. When VEGA scanner is successful connected, scanner will initiate with short beep sounds. Blue and red led will also blink followed by a long beep sound. Blue led will slow flash to finish the set up. 4.3.
PAGE 26
24 Configuring the VEGA Chapter 5 Cover Display
PAGE 27
Scantech-ID 5.1 SETUP COVER DISPLAY The VEGA scanner has the opportunity to change the decorative cover display on the top of the scanner into a display that can show our own commercial message. 5.1.1 Message Format Create your own commercial message with the following outline format, use thicker paper 5.1.2 Change Cover Display Follow the next instruction steps to change the black Cover Display into the transparent Cover Display, so that your customers can read your own commercial massage.
PAGE 28
26 Configuring the VEGA Step 1: Press out the front rubber lid toward the arrow. ➀ Step 2: Pull out the front rubber lid off the main unit. Step 3: Press out top cover rim from the inner lock.
PAGE 29
Scantech-ID Step 4: Press out the other side of inner lock and remove the complete cover. ➃ Step 5 Assemble transparent top cover rim into inner lock. ➄ Step 6 Assemble another side transparent top cover rim into the inner lock.
PAGE 30
28 Configuring the VEGA Step 7 Insert your commercial message card into the top cover toward the arrow. ➆ Step 8 Assemble the front rubber lid into the main unit toward the arrow.
PAGE 31
Scantech-ID Chapter 6 Configuring the VEGA
PAGE 32
30 Configuring the VEGA 6.1 PREFACE How to configure the VEGA: The Barcode Programming Feature gives the possibility to change the VEGA scanner settings with use programming codes or with the Utility Tool. 6.1.1 Changing Scanner Settings with Programming Codes You can set-up your VEGA by scan all necessary programming codes for parameters that meet applications. After these scans the VEGA is direct permanently saved.
PAGE 33
Scantech-ID In this case you can set-up your VEGA by using the advanced Utility Tool. This tool can be used with the following operation systems: Windows98, Windows2000, Windows XP en Windows Vista. This Utility Tool can be delivered on request. Please contact ScantechID Technical Support Department.
PAGE 34
32 Configuring the VEGA 6.
PAGE 35
Chapter 7 Programming Codes
PAGE 36
34 7.1 RETURN TO DEFAULT 7.1.1 Scan this programming code to set the scanner parameters to factory default: Set the scanner to Factory Default - Reset all configuration parameters to their factory default setting. - After this reset you must select all required parameters that meet applications. 7.1.2 Scan this programming code to set the cradle parameters to factory default: Note: The parameter barcode only used V-1020BT series model. Please don’t used setting for V-1020 series model.
PAGE 37
Scantech-ID 7.2 RS-232 MODE PARAMETERS Note: These parameter barcodes only used setting RS-232 interface for V1020.Please don’t used setting for V-1020BT series model. 7.2.
PAGE 38
36 9600 19200 38400 57600(*) 115200 128000 230400 256000 460800
PAGE 39
Scantech-ID 7.2.2 Data bits Data Bits 7 Data Bits 8(*) 7.2.3 Stop bits Stop Bits 1(*) Stop Bits 2 7.2.
PAGE 40
38 7.2.5 Hardware/Software Protocols Timeout compose (ms): 500 compose (ms):1000(*) compose (ms): 1500 compose (ms): 2000 compose (ms): 2550 7.2.
PAGE 41
Scantech-ID 7.2.7 RS-232 Parameters–ACK Not Active(*) Active Default: 06H(*) 7.2.
PAGE 42
40 7.2.9 Software Protocol–XON/XOFF Active Not Active(*) 7.2.
PAGE 43
Scantech-ID 7.2.11 RS-232 Parameters-LRC (Longitudinal Redundancy Check) Not Active(*) Active 7.2.
PAGE 44
42 7.2.
PAGE 45
Scantech-ID 7.3 BLUETOOTH SCANNER SETUP 7.3.1 Bluetooth Default Setting Default Setting 7.3.2 Scanner Server/Client Mode Scanner Server Mode Barcode Scanner Client Mode Barcode 7.3.3 Sleep Mode Sleep Mode 1 min. ON(*) Sleep Mode 10min.
PAGE 46
44 7.3.4 Memory Mode Memory Mode ON Memory Mode OFF(*) Memory Read Memory Clear 7.3.
PAGE 47
Scantech-ID 7.3.6 Set Pin Code Charactor (PINCODE max. 6 digits, 0-9and A-Z ASCII CODE) 1) Begin to Set PINCODE 2) Go to the ASCII Tables in 9.10, scan 6 labels that represents the PINCODE.
PAGE 48
46 7.4 BLUETOOTH CRADLE SETUP 7.4.1 Set Cradle Pin Code Mode Set Default Security Code Barcode (PINCODE = 000000) Set Security ON Barcode Set Security OFF Barcode 7.4.2 Set Pin Code Barcode (PINCODE max. 6 digits ,0-9,A-Z ASCII CODE ) 1) Begin to Set PINCODE 2) Go to the ASCII Tables in 9.10, scan 6 labels that represents the PINCODE.
PAGE 49
Scantech-ID 7.4.3 Set Cradle Interface Barcode Note: These parameter barcodes only used setting RS-232 interface for V1020BT series model. Please don’t used setting for V-1020 series model. Set Cradle Interface Default Barcode （default RS232, 19200, N-8-1） Set Cradle KB Interface Barcode Set Cradle RS232 Interface Barcode Set Cradle USB HID Interface Barcode 7.4.3.
PAGE 50
48 1200 2400 4800 9600 <19200> 38400 7.4.3.
PAGE 51
Scantech-ID 7.4.3.3 Cradle Stop bits <1 bit> 2 bits 7.4.3.4 Cradle Parity Even Odd Mark Space 7.4.3.
PAGE 52
50 ACK/NAK Enable XON/XOFF Enable < XON/XOFF Disable > 7.4.3.6 Cradle Keyboard Wedge mode parameters 1.
PAGE 53
Scantech-ID 2. Upper/Lower Case Upper Case Lower Case 3. Send Character by ALT Method Enable 4.
PAGE 54
52 5. Time out Between Characters <0 ms> 5 ms 10 ms 25 ms 50ms 100ms 6.
PAGE 55
Scantech-ID Spanish French German Swedish Switzerland Hungarian Japanese Belgium Portuguese Denmark
PAGE 56
54 Netherlands Turkey Reserved 1 7.5 DECODING SELECTION 7.5.
PAGE 57
Scantech-ID BPO ON BPO OFF (*) Canada Post ON Canada Post OFF (*) CODABAR ON CODABAR OFF (*) Codablock A ON Codablock A OFF (*) Codablock F ON Codablock F OFF (*)
PAGE 58
56 CODE 11 ON CODE 11 OFF (*) CODE 39 ON (*) CODE 39 OFF CODE 93 ON CODE 93 OFF (*) CODE 128 ON (*) CODE 128 OFF GS1-128 ON (*)
PAGE 59
Scantech-ID GS1-128 OFF DATAMATRIX ON (*) DATAMATRIX OFF Dutch Post ON Dutch Post OFF (*) EAN-8 ON (*) EAN-8 OFF EAN-13 ON (*) EAN-13 OFF
PAGE 60
58 EAN 128 ON (*) EAN 128 OFF GS1 CC-A/B ON GS1 CC-A/B OFF (*) GS1 CC-C ON GS1 CC-C OFF (*) GS1 DataBar-Omni ON GS1 DataBar-Omni OFF (*) GS1 DataBar-Limited ON
PAGE 61
Scantech-ID GS1 DataBar-Limited OFF (*) GS1 DataBar-Expanded ON GS1 DataBar-Expanded OFF (*) Infomail ON Infomail OFF (*) INTERLEAVED 2 of 5 ON INTERLEAVED 2 of 5 OFF (*) Japan Post ON Japan Post OFF (*)
PAGE 62
60 Matrix 2 of 5 ON Matrix 2 of 5 OFF (*) MaxiCode ON MaxiCode OFF (*) MicroPDF417 ON MicroPDF417 OFF (*) MSI ON MSI OFF (*) PDF417 ON (*)
PAGE 63
Scantech-ID PDF417 OFF Planet ON Planet OFF (*) PLESSEY ON PLESSEY OFF (*) Postnet ON Postnet OFF (*) QR Code ON QR Code OFF (*)
PAGE 64
62 Standard 2 of 5 ON Standard 2 of 5 OFF (*) Sweden Post ON Sweden Post OFF (*) Telepen ON Telepen OFF (*) TLC 39 ON TLC 39 OFF (*) UPC-A ON (*) UPC-A OFF
PAGE 65
Scantech-ID UPC-E ON (*) UPC-E OFF Note: This step does not include codes for all support Barcode symbologies. For a complete overview of support symbologies see appendix. If you need programming codes for symbologies which are not available in this chapter, please contact Scantech-ID Technical Support department or use VEGA utility tool. 7.5.2 Disable All Symbologies. Disable All Symbologies - Disabled all Symbologies. - Use the“OFF”option to disable individual symbologies.
PAGE 66
64 7.6 AUSTRALIAN POST SETTINGS 7.6.
PAGE 67
Scantech-ID 7.7 7.7.1 AZTEC SETTINGS Structure Append Mode Active Not Active(*) 7.7.2 Aztec Runes Active Not Active(*) 7.7.
PAGE 68
66 7.7.
PAGE 69
Scantech-ID 7.8 BPO SETTINGS 7.8.1 Symbology Identifier UDSI-Default"P2"(*) Code Mark-Default"*"(*) 7.8.
PAGE 70
68 7.9 CANADA POST SETTINGS 7.9.
PAGE 71
Scantech-ID 7.10 CODABAR SETTINGS 7.10.1 Symbology Identifier UDSI-Default"B7"(*) Code Mark- Default"D"(*) 7.10.
PAGE 72
70 7.10.3 CLSI Library System Active(insert spaces) Not Active(*) 7.10.4 Check Digit Verification Used Not Used(*) 7.10.
PAGE 73
Scantech-ID 7.10.
PAGE 74
72 7.11 CODABLOCK SETTINGS 7.11.
PAGE 75
Scantech-ID 7.12 CODE 11 SETTINGS 7.12.1 Symbology Identifier UDSI-Default"C1"(*) Code Mark-Default"*"(*) 7.12.
PAGE 76
74 7.13 CODE 39 SETTINGS 7.13.1 Symbology Identifier UDSI-Default"B1"(*) Code Mark-Default"*"(*) 7.13.2 Format Standard 43 Characters(*) Full ASCII (Extended) 7.13.
PAGE 77
Scantech-ID 7.13.4 Accepted Characters * Only(Standard Code 39)(*) $ Only(Trioptic Code 39) $ and * (Standard and Trioptic Code 39) 7.13.
PAGE 78
76 Check Digit Transmitted 7.13.6 Reading Range Extended (*) Normal 7.13.
PAGE 79
Scantech-ID 7.14 CODE 93 / CODE 93I SETTINGS 7.14.
PAGE 80
78 7.15 CODE 128 / GSI-128 SETTINGS 7.15.1 Symbology Identifier UDSICode 128-Default"B3"(*) UDSIGS1-128-Default"C9"(*) Code MarkCode 128-Default"D"(*) Code MarkGS1-128-Default"D"(*) 7.15.
PAGE 81
Scantech-ID 7.15.3 CIP 128 French Pharmaceutical Codes Active Not Active (*) FNC1 Separator Character (GS1-128 norms)-(1Dh)(*) 7.15.
PAGE 82
80 7.15.
PAGE 83
Scantech-ID 7.15.6 GTIN Processing For GS1-128 Active Not Active (*) 7.15.
PAGE 84
82 7.16 DATAMATRIX SETTINGS 7.16.
PAGE 85
Scantech-ID 7.17 DUTCH POST SETTINGS 7.17.
PAGE 86
84 7.18 EAN /UPC PARAMETERS SETTINGS 7.18.
PAGE 87
Scantech-ID ISMN – Active ISMN - Not Active (*) ISSN – Active ISSN - Not Active (*) GTIN Processing – Active GTIN Processing - Not Active (*)
PAGE 88
86 7.18.
PAGE 89
Scantech-ID 7.18.
PAGE 90
88 Transmission OFF 7.18.
PAGE 91
Scantech-ID 7.19 GS1 COMPOSITE SETTINGS 7.19.1 EAN/UPC Composite Message Decoding Auto-Discriminate (*) Always Linked Never Linked 7.19.
PAGE 92
90 Code Mark–CC-C-Default"*"(*) 7.19.
PAGE 93
Scantech-ID 7.20 GS1 DATABAR SETTINGS 7.20.
PAGE 94
92 7.21 INFOMAIL SETTINGS 7.21.
PAGE 95
Scantech-ID 7.22 INTERLEAVED 2 OF 5 PARAMETERS 7.22.1 Check Digit Verification Not Used (*) Modulo 10 French CIP Not Transmitted (*) Transmitted 7.22.
PAGE 96
94 7.22.
PAGE 97
Scantech-ID 7.23 JAPAN POST SETTINGS 7.23.1 Symbology Identifier UDSI-Default"P5"(*) Code Mark-Default"*"(*) 7.23.
PAGE 98
96 7.24 MATRIX 2 OF 5 SETTINGS 7.24.
PAGE 99
Scantech-ID 7.25 MAXICODE SETTINGS 7.25.1 Symbology Identifier UDSI-Default"D2"(*) Code Mark-Default"*"(*) 7.25.2 Mode 0 Active Not Active(*) 7.25.
PAGE 100
98 7.26 MICROPDF417 SETTINGS 7.26.1 Symbology Identifier UDSI–Default"C8"(*) Code Mark-Default"*"(*) 7.26.
PAGE 101
Scantech-ID 7.27 MSI CODE PARAMETERS SETTINGS 7.27.1 Symbology Identifier UDSI-Default"B8"(*) Code Mark-Default"D"(*) 7.27.
PAGE 102
100 7.28 PDF417 SETTINGS 7.28.1 Symbology Identifier UDSI-Default"C7"(*) Code Mark-Default"*"(*) 7.28.2 Irregular PDF Active Not Active(*) 7.28.
PAGE 103
Scantech-ID 7.28.
PAGE 104
102 Addressee Transmitted Addressee Not Transmitted (*) File Size Transmitted File Size Not Transmitted (*) Checksum Transmitted Checksum Not Transmitted (*)
PAGE 105
Scantech-ID 7.29 PLANET SETTINGS 7.29.1 Symbology Identifier UDSI-Default"P1"(*) Code Mark-Default"*"(*) 7.29.
PAGE 106
104 7.30 PLESSEY CODE PARAMETERS 7.30.1 Symbology Identifier UDSI–Default"C2"(*) Code Mark-Default"D"(*) 7.30.
PAGE 107
Scantech-ID 7.31 POSTNET SETTINGS 7.31.1 Symbology Identifier UDSI-Default"P0"(*) Code Mark-Default"*"(*) 7.31.
PAGE 108
106 7.32 QR CODE SETTINGS 7.32.1 Model 1 Control Active Not Active (*) 7.32.
PAGE 109
Scantech-ID 7.33 STANDARD 2 OF 5 SETTINGS 7.33.1 Symbology Identifier UDSI-Default"B5"(*) Code Mark-Default"D"(*) 7.33.
PAGE 110
108 7.33.
PAGE 111
Scantech-ID 7.34 SWEDEN POST SETTINGS 7.34.
PAGE 112
110 7.35 TELEPEN SETTINGS 7.35.1 Symbology Identifier UDSI-Default"C6"(*) Code Mark-Default"*"(*) 7.35.
PAGE 113
Scantech-ID 7.36 TLC 39 SETTINGS 7.36.1 Symbology Identifier UDSI-Default"H0"(*) Code Mark-Default"*"(*) 7.36.2 Linear Transmission Only Active Not Active (*) 7.36.
PAGE 114
112 7.37 MISCELLANEOUS PARAMETERS 7.37.1 Symbology Identifier Symbology Identifier Transmitted Symbology Identifier Not Transmitted(*) With this function ON, a leading character will be added to the output string while scanning code, user may refer to the following table to know what kind of barcode is being scanned. Please refer to the table below for matching code Symbology Identifier of codes read in.
PAGE 115
Scantech-ID 7.38 PREAMBLES AND POSTAMBLES 7.38.1 Preamble The scanner can be programmed to output Barcode data according the following format: [PREAMBLE STRING] [BAR CODE DATA] Example: To send a in front of the barcode, scan only programming code .
PAGE 116
114 7.38.2 Postamble The scanner can be programmed to output Barcode data According to the following format: [BAR CODE DATA] [POSTAMBLE STRING] Example: To send a after of the Barcode, scan only programming code . As a result, the scanner will give the following barcode data output: [BAR CODE DATA] [] Postamble None CR+LF (*) CR LF It could be possible that you need other Postambles, in that case use VEGA utility Tool or contact Scantech-ID Technical Support Department.
PAGE 117
Scantech-ID Chapter 8 Operating Settings
PAGE 118
116 8.1 SCANNING TRIGGERING A reading session begins (lighting and decode processing on) when beam is activated and stops when beam is deactivated. Continuous Scanning When the scanner is turned on a continuous reading session begins (lighting and decode processing on). Note: The continue scanning mode doesn’t support the V-1020BT. Pulse A reading session begins when beam is activated and stays on until a period of inactivity lasting the time specified by the timeout.
PAGE 119
Scantech-ID After a period of inactivity lasting the time specified by the timeout, the scan engine starts flashing, checking for a barcode to be read. When a barcode is detected, the lighting automatically turns on and stays on until another period of inactivity (timeout). After the timeout the scan engine starts flashing again. Level + Flashing This mode allows you the switch between level and flashing mode. When the scanner is turned on it is in flashing mode (see flashing mode for explanation).
PAGE 120
118 Autostand This mode allows you to switch from Flashing trigger mode to Level trigger mode. Autostand begins in flashing mode: At power up the lighting and decoding are on (no need to activate the trigger line) and after a period of inactivity lasting the time specified by the trigger timeout, the scanner starts flashing. To switch to Level trigger mode activate the trigger line (press the trigger).
PAGE 121
Scantech-ID 8.
PAGE 122
120 8.3 GOOD READ MODE When active, the scan engine stops the reading session after a successful decoding. - NOTE: this parameter is NOT used with continuous and continuous + flashing modes.
PAGE 123
Scantech-ID 8.4 BUZZER BEEP TONE 8.4.1 Beep Tone Setup High (*) Medium Low 8.4.
PAGE 124
122 8.4.3 Beep Duration 60 msec 80 msec (*) 200 msec Off 8.4.
PAGE 125
Scantech-ID 8.5 GOOD READ DURATION 8.5.1 Good Read Led Duration 80 msec (*) 0.5 sec 1 sec Off 8.5.
PAGE 126
124 8.5.3 Setup Beep On (*) Off 8.
PAGE 127
Scantech-ID Chapter 9 Imager settings
PAGE 128
126 9.1 IMAGER MODE You can set the best reading performance of your VEGA by adjusting certain imager parameters. To choose the best reading performance, depends on the environment, your used application and type of barcodes.  Area mode for decode 1D and 2D barcodes.  Linear mode for decode 1D Barcodes. Area mode allows you to set the position of the VEGA in any direction regardless of the orientation of the barcode, and perform a good read on 1D and 2D barcodes.
PAGE 129
Scantech-ID Appendixes A. DECIMAL VALUE TABLE.........................123 B. ASCII TABLE.............................................124 C. READABLE SYMBOLOGIES....................125 D. TECHNICAL SPECIFICATIONS................126 E. SCAN MAP.................................................127 F. OVERVIEW PARTNUMBERS....................
PAGE 130
128 A.
PAGE 131
Scantech-ID B.
PAGE 132
130 C.
PAGE 133
Scantech-ID D.TECHNICAL SPECIFICATIONS Physical Characteristics Scanner Weight V-1020 Approx. 133g V-1020BT Approx. 180g Cradle Weight Approx. 145g Charger Weight Approx. 135g Material ABS Plastic Connector RJ 45C 10Pins Scanner Dimension 186.8 mm x 81.6 mm x 63.9 mm Cradle Dimension 123.9mm x 120mm x 71.4mm Operational Light source Scan rate Visible Red light 650nm + 10nm 200scans/sec auto adaptive in linear mode. 56 images/sec auto adaptive in 2D mode.
PAGE 134
132 Radio Characteristics Bluetooth Module Frequency Band Modulation Method RF Output Power Bluetooth V2.0 Standard 2.402GHz ~ 2.480GHz GFSK for 1Mbps Class 2 (under 4 dBm) Class 1 (under 20dBm) Bluetooth distance range Bluetooth distance range Class 2 up to 10M(33”) Class 1 up to 100M(330”) Environmental Operating Temp. 0°C to 50°C (32°F to 122°F) Storage Temp.
PAGE 135
Scantech-ID E.SCAN MAP Typical Reading Distances in 0" 4" 8" 12” 16" 20" 10" 25 8" 20 Data Matrix 7.5 mils 6" 15 PDF417 6.6 mils 4" 10 5 2" 0 0" 5 2" 4" 10 0.125 mm/ 5 mils 15 6" 0.25 mm / 10 mils 8" 20 100% contrast UPC / EAN 10" 25 0.5 mm / 20 mils cm 0 10 20 30 40 50 VEGA Typical Reading Distance: These distances are measured in an office environment (250 lux).
PAGE 136
134 VEGA Typical Reading Distances (centimeters) Symbology Density Minimum Maximum Distance Distance Code 39 0.125 mm 7.2 cm 13.1 cm 0.20 mm 3.8 cm 22.5 cm 0.25 mm 3.4 cm 27 cm 0.5 mm 5 cm 44 cm 1 mm 8 cm 83 cm UPC / EAN 0.33 mm 5 cm 32 cm Data matrix 0.191 mm 6.3 cm 17.2 cm 0.254 mm 4.8 cm 22 cm 0.381 mm * 29 cm PDF417 0.16 mm 6.2 cm 15.4 cm 0.254 mm 4.5 cm 23 cm 0.381 mm 4 cm 37 cm *Minimum distance depends on symbology length and scan angle.
PAGE 137
Scantech-ID F.OVERVIEW MODEL NUMBERS VEGA with Area Imager Version with RS232 interface: 1. A273002 VEGA V-1020-02 2. A274002 VEGA V-1020BT C2 -02 3. A276002 VEGA V-1021BT C1 -02 Version with KBW interface: 4. A274004 VEGA V-1020BT C2 -04 5. A276004 VEGA V-1021BT C1 -04 Version with USB (HID KBW) interface: 6. A273004 VEGA V-1020-04 7. A274003 VEGA V-1020BT C2 -03 8. A276003 VEGA V-1021BT C1 -03 Version with USB (virtual com port) interface: 9.
PAGE 138
136 Scantech-ID BV Nijverheidsweg Noord 60-34 3812 PM Amersfoort The Netherlands Phone: Fax: +31 (0)33 469 84 00 +31 (0)33 465 06 15 E-mail: Internet: info@scantech-id.com www.scantech-id.