Owner's Manual
No6 (3.5mm) x 3/4"
(19mm)
~
self -tapping CSK
Philips
screw x4
Powerdrill
Onnm
3mm x 10mm
Pan
head
Philips
Thread
forming
screw x5
~
SC-CW-01 E-005
Jigsaw
Wireless
charger
x1
>
Silicone
Drain
Pipe 8mm
(5
/16")
Sea
lant
internal diameter
(Optional,
not included)
Fo
r latest tech info visit: www.scanstrut.c
om
/rokk-wireless
The
product
must
be installed
in
accordance
with
the
instructions provided. Failure
to
do
so could result in personal
injury
, damage
to
your
vessel/vehicle
and/or
product
failure.
Scanstrut recommends installation is carried
out
by
a qualified electrician.
No
liability
is accepted
for
damage
and
/
or
injury
caused
by
incorrect installation.
&WARNING
This
produ
ct is
to
be
fitted
to
a 12V DC
or
24V
DC
battery/power
source
only
.
The
power
supply
must
be
switched
off
before insta
ll
ation.
An
appropriate fuse
or
circuit breaker
must
be
used in-line between
the
battery/
power source and
the
product.
Check
for
correct polar
ity
of
a
ll
wiring
before switching
the
power
on
.
This
product
may
contain
high
vo
ltages.
Do
not
tamper
with
th
e product.
This
product
is
NOT
approved
for
use
in
hazardous/flammable atmospheres.
Do
NOT install
in
a hazardous/flammable atmosphere e.g.
engine
rooms.
Before dr
illing
any holes, ensure
the
area
behind
the
mounting
location
is
clear
of
wires, fuel and all
other
hazardous objects.
Ensure any
ho
l
es
cut
will
not
significantly weaken
the
structure
of
the
surface.
If
the
product
needs
to
be
mounted
outside,
it
must
be
mounted
in
a location
safely above
the
waterline, where
it
is
not
at
risk
of
being
submerged.
The
product
c
annot
charge
through
a metallic surface.
~
C
:~p::
~
~
specifically
for
the
charging
of
Qi compatible devices.
The cable
must
be
retained
and
not
interfere
with
mechanical systems.
This
product
contains
no
user serviceable components. Do NOT
attempt
to
repair
or
alter
the
product
in any
way
.
The hi
gh
friction
top
surface does
not
ensure
the
device
will
not
slip
during
extreme operating
env
ir
onments
such as
high
acceleration
and
deceleration.
If
a phone case
which
is
thicker
tha
n
3mm
is
used
the
device may
not
charge.
When used
in
a
high
ambient
temperature/direct sunlight
the
product
may
temporar
ily
shut
down,
this
is a safety feature
of
the
electronics.
The
IP
r
ating
is
only
valid
if
correctly installed using
the
instructions and
on
a
perfect
ly
flat
non
-porous smooth surface.
When selecting a
mounting
location, avoid places exposed
to
heat-radiating
appliances and
poor
ly-ventilated areas.
EMC
INSTALLATION
GUIDELINES
Scanstrut products
conform
to
Electromagnetic
Compatibility
(EMC)
regulations,
to
ensure
that
electromagnetic interference between
equipment
is minimised.
WIRING
When extending
the
ca
bl
e
from
your
battery
/
power
source
to
the
product
, ensure
there
is
a
minimum
of
1 0V
being
provided
to
the
product
continuously.
We
recommend a
wire
gauge
of
1
SAWG
(0.82mm
2
)
for
any l
ength
of
cable extension.
This schematic is
to
Illustrate
how
the
product
should
be
connected
to
a 12V DC
or
24V
DC
battery/
power
supply.
ENVIRONMENTAL
PROTECTION
Waste electrical products should
not
be
disposed
of
with
household
~
waste.
Please
recycle
where
facilities exist. Check
with
your
Local
A
Authority
or
retailer
for
recycling advice.