Owner's Manual
Smart
LED
li
ght
gu
i
de:
Solid
red
Product has power and ready
to
charge.
Solid
green
Product charging.
Flashing
red
1. Foreign object detection:
metallic object placed
on
top
that is not Qi compatible.
or
2. Thermal cutout:
internal temperature is
too
high/ low.
Wait
for
product
to
return
to
operating temperature.
Flashing
green/red
Input current is
too
low.
This product is designed
to
securely mount phones under
normal usage conditions. The end-user is entirely responsible for
conditions in which their device is used. See WARRANTY section
for
further details.
Scanstrut
recommends
installation is carried
out
by
a
qualifi
ed
electrician.
No
liability is
accepted
for
damage
and/or
injury caused
by
incorrect installation.
WARNING:
This product is
to
be connected
to
a 12V DC
or
24V DC battery
power source only.
The power supply must
be
switched off before installation.
An appropriate fuse or circuit breaker must
be
used between
the battery /
power
source and this product. Check
for
correct
polarity
of
all wiring before switching the
power
on.
This product
may
contain high voltages.
Do
not
tamper with the
product.
This product is NOT approved for use in hazardous/flammable
atmospheres. Do NOT install in a hazardous/flammable
atmosphere e.g. engine room.
Before drilling any holes, ensure the area behind
the
mounting
location is clear
of
wires, fuel and all other hazardous objects.
Ensure any holes
cut
will not significantly weaken the structure
of
the mounting surface.
If the product needs
to
be mounted outside, it must be mounted
in a location safely above the waterline, where
it
is not
at
risk
of
being submerged.
CAUTION:
IN
EXTREME
USAGE
ENVIRONMENTS
PERFORMANCE
MAY
VARY.
The product is designed specifically
for
the
charging
of
Qi
compatible devices.
The cable must
be
retained and not interfere with mechanical
systems.
This product contains
no
user serviceable components. Do NOT
attempt
to
repair
or
alter the product in any way.
This product will charge through non-metallic phone cases
up
to
-3mm
thick. Phone cases may alter overall charge performance.
When used in a very high/low ambient temperature/direct
or
prolonged sunlight the product may temporarily shut down, this is
a safety feature
of
the electronics.
The
IP
rating is only valid
if
correctly installed as per these
instructions and
on
a perfectly flat, non-porous, smooth surface.
When selecting a mounting location, avoid places exposed
to
heat-radiating appliances and poorly ventilated areas.
EMC INSTALLATION GUIDELINES:
Scanstrut products conform
to
Electromagnetic Compatibility
(EMC) regulations,
to
ensure that electromagnetic interference
between equipment is minimised.
Correct installation
is
required
to
ensure that electromagnetic
interference is kept
to
a minimum.
WIRING:
When extending
the
cable from battery/power source
to
the
product, ensure there is consistently a minimum
of
1 0V being
provided
to
the product. A wire gauge
of
18AWG (0.82mm2) is
recommended for any length
of
cable extension.
The schematic in step 6 is
to
illustrate
how
the product should
be
connected
to
a 12V DC
or
24V
DC battery/power supply.
ENVIRONMENTAL PROTECTION:
Waste electrical products should not
be
disposed
of
with
household waste. Please recycle where facilities exist. Check with
your Local Authority
or
retailer
for
recycling advice.
IMPORTANT:
Scanstrut Ltd. accepts no responsibility for any injuries
or
other damages arising from the use
of
their products in any
circumstances.
WARRANTY:
A 2 year, non-transferrable warranty covers this Scanstrut product
only and not any devices that are mounted in it
or
on
it. No
warranty is given for users' devices and users expose their devices
to
hazards, known
or
unknown, at their
own
risk.