Owner's Manual
Sm
art
LED
li
ght
guid
e:
Solid
red
Product has power and
ready
to charge.
Solid
green
Product charging.
Flashing
red
1.
Foreign
object detection:
metallic object placed on top
that
is
not
Qi
compatible.
or
2.
Thermal cutout:
internal temperature
is
too high/
low.
Wait
for product to return to operating temperature.
Flash
i
ng
green/red
Input current
is
too
low.
This
product
is
designed to securely mount phones under
normal usage conditions.
The
end-user
is
entirely responsible for
conditions
in
which their device
is
used.
See
WARRANTY
section
for further details.
Scanstrut recommends installation is carried out by a
qualified electrician.
No
liability is accepted
for
damage
and/or injury caused
by
incorrect installation.
WARNING:
This product
is
to be connected to a 12V
DC
or 24V
DC
battery
power source
only.
The power supply must be switched off before installation.
An
appropriate
fuse
or circuit breaker must be used between
the battery / power source
and
this product. Check for correct
polarity of
all
wiring before switching the power on.
This product may contain high voltages.
Do
not tamper with the
product.
This product
is
NOT
approved for use
in
hazardous/flammable
atmospheres.
Do
NOT
install
in
a hazardous/flammable
atmosphere e.g. engine
room.
Before drilling any
holes,
ensure
the
area
behind the mounting
location is clear of
wires,
fuel
and
all
other hazardous objects.
Ensure
any holes cut
will
not significantly
weaken
the structure of
the mounting surface.
If the product needs to be mounted outside, it must be mounted
in
a location safely above
the
waterline,
where
it
is
not at risk of
being submerged.
CAUTION:
IN
EXTREME
USAGE
ENVIRONMENTS
PERFORMANCE
MAY
VARY.
The
product
is
designed specifically for the charging
of
Qi
compatible devices.
The
cable must
be
retained and not interfere with mechanical
systems.
This
product contains no user serviceable components.
Do
NOT
attempt to repair or alter the product
in
any
way.
This
product
will
charge through non-metallic phone cases
up
to
-3mm
thick.
Phone
cases may alter
overall
charge performance.
When
used
in
a very high/low ambient temperature/direct or
prolonged sunlight the product may temporarily shut down, this
is
a
safety feature of the electronics.
The
IP
rating
is
only
valid
if correctly installed
as
per these instructions
and
on
a perfectly flat, non-porous, smooth surface.
When
selecting a mounting location, avoid places exposed to
heat-radiating appliances and poorly ventilated
areas.
EMC
INSTALLATION
GUIDELINES:
Scanstrut products conform to Electromagnetic Compatibility
(EMC)
regulations, to
ensure
that electromagnetic interference between
equipment
is
minimised.
Correct installation
is
required to
ensure
that electromagnetic
interference
is
kept to a minimum.
WIRING:
When
extending the cable from battery/power source to the product,
ensure
there
is
consistently a minimum of 1 0V being provided to the
product. A wire gauge
of
18AWG
(0
.82mm2)
is
recommended for
any
length
of
cable extension.
The
schematic
in
step 7
is
to illustrate how
the
product should be
connected to a 12V
DC
or 24V
DC
battery/power
supply.
ENVIRONMENTAL
PROTECTION:
Waste electrical products should not be disposed of with household
waste.
Please
recycle
where
facilities exist. Check with your Local
Authority or retailer for recycling advice.
IMPORTANT:
Scanstrut Ltd. accepts no responsibility for
any
injuries
or other dam-
ages
arising
from the use of their products
in
any
circumstances.
WARRANTY:
A 2
year,
non-transferrable warranty covers this Scanstrut product
only
and
not any devices that
are
mounted
in
it or
on
it.
No
warranty
is
given
for users' devices and users expose their devices to hazards,
known or unknown, at their own
risk.