Service manual

7020
SOLUTION:
CAUSE: Fixing heater/2 failed.
SOLUTION: To check the fixing heater /2 lamp, perform the following.
1. Access the 47 multimode (power the machine ON, while holding down on the 4 and 7 keys)
input code 45, press *-2-*.
2. Press the print button and see if the fixing heater/2 comes ON.
3. If the lamp does not come ON, replace the fixing lamp/2 (p/n 26NE83030).
USAGE:
1
DF314, how to tighten the hinge pressure.DESCRIPTION: SOLUTION ID:
116900
SOLUTION:
The DF314 hinge pressure can not be tightened.
Note: If the DF314 feeder is not staying in the upright position correctly and is falling onto the
platen glass, replace the pressure hinge (p/n 13GL10110).
USAGE:
1
LCD messages are in Japanese language.DESCRIPTION: SOLUTION ID:
116980
SOLUTION:
CAUSE: Incorrect software dipswitch settings for language display.
SOLUTION: To program the machine to display English language, perform the following:
1. Access the 25 mode (turning the machine ON while pressing the 2 and 5 keys, then pressing
the OK key).
2. Use the function keys below the display window to access and set the following software
dipswitches to display English language:
5-0 set to 1
5-1 set to 0
USAGE:
1
FK101, when mixed original mode is selected, the document is scanned twice.DESCRIPTION: SOLUTION ID:
117439
SOLUTION:
This is normal operation of mixed original mode. The document is scanned twice for size
determination.
Notes:
1. The mixed original feed process is the same as in the double-sided copy mode.
2. Refer to DF314 Service Manual (2/2000) page 5 and 13 for more detail on the mixed original
feed process.
USAGE:
1
FS107, parts change to the Paper detecting board (p/n 13GQ60190) and Detecting spring
(p/n 13GQ60210).
DESCRIPTION: SOLUTION ID:
117806
SOLUTION:
[[Changes to these parts have been made to prevent the Detecting spring from detaching from the
Paper detecting board.| IMAGE V:\bitmaps\fs107partschange.bmp SCROLL]]
The hook portion of the spring is fixed with adhesive in manufacturing.
1. The shape of the hook portion of the Detecting spring has been changed in manufacturing. The
new part number for the Detecting spring is (p/n 13GQ60211).
2. A notch has been added to the Paper detecting board to hook the Detecting spring. The new
part number for the Paper detecting board is (p/n 13GQ60191).
Notes:
1. The Detecting spring and paper detecting board are not interchangeable; the current and new
types cannot be mixed.
2. The new Detecting spring and the new paper detecting board must be replaced as a set.
USAGE:
1
After resetting the PM counter, CALL FOR PM message is still indicated at power up.DESCRIPTION: SOLUTION ID:
117975
SOLUTION:
CAUSE: The PM cycle is set to zero (0), causing the machine to constantly detect the need for a
PM.
SOLUTION: To program the PM cycle, perform the following:
1. Power the copier OFF.
2. Access the 25 mode (power the copier ON, while pressing the 2 and 5 keys).
3. Touch [2. PM COUNT/CYCLE] on the touchscreen.
4. Touch [2. PM CYCLE set] on the touchscreen
5. Input the desired PM cycle using the numeric keys. Enter upper 3-digit (hundred thousand, ten
thousand and thousand) only.
6. Touch [SET] on the touchscreen.
7. Power the copier OFF/ON to exit the 25 mode.
Note: The factory default setting for the PM cycle is 100,000 copies.
USAGE:
1
Shadows around the edges of Booklet mode copies.DESCRIPTION: SOLUTION ID:
117998
SOLUTION:
CAUSE: The RADF Centering adjustment is incorrect.
USAGE:
1
91
Copyright 2005, Konica Minolta Business Solutions U.S.A., Inc.
May 2005