Service manual

7020
is highlighted.
6. Press EDIT on touchscreen until desired quantity is reached.
7. Press BACK twice.
8. Press RETURN to revert to standby mode.
FK101, how to program to initialize in fax mode.DESCRIPTION: SOLUTION ID:
114520
SOLUTION:
To program the 7020 to initialize in fax mode, perform the following:
1. The 7020 firmware must, at minimum, be flashed to level 28 system and 25 Image and the
FK101 firmware must, at minimum, be flashed to level 15.
2. From the copier mode, press the HELP (?) button, located to the right of the touchscreen.
3. From the touchscreen, select Key-Ope mode.
4. Enter a Key Operator passcode if applicable.
5. Select [1. FAX].
6. Select FAX SCREEN SET.
7. Press the left down arrow to scroll to the next page.
8. Scroll down to FAX SCREEN FIRST.
9. Press EDIT to set FAX SCREEN FIRST to ON.
10. Power OFF/ON the sub switch (SW2) on the left side of the operation panel.
Note: Enabling this option only allows the 7020 to initialize (power up) in the FAX mode,
Auto-Reset timer or button will not bring the 7020 back to FAX mode.
USAGE:
1
FK101, will faxes in memory be lost if power is turned OFF?DESCRIPTION: SOLUTION ID:
114594
SOLUTION:
The backup battery will hold the FK101 settings and image data for 60 minutes when fully charged.
USAGE:
1
FK101, how to program the Communication Journal.DESCRIPTION: SOLUTION ID:
114743
SOLUTION:
To program the Communication Journal, perform the following:
1. Access the Key operator mode (press the help key) help mode will be displayed.
2. Press (Key-ope mode) located in the lower left hand corner, key operator mode will be
displayed.
3. Press [2. Fax] fax initial setting menu will be displayed.
4. Press [Report output set] report output mode will be displayed.
5. Communication Journal is the first option displayed.
6. Press [edit] until desired setting is displayed. Setting ranges are (OFF, or Daily, or 100+ Daily.).
7. Press [BACK] to exit to Fax initial setting menu.
8. Press [BACK] to exit to the key operator mode.
9. Press [return] to exit to the main copy screen.
USAGE:
1
FS107, how to disable the STAPLE and SORT feature in the OUTPUT mode.DESCRIPTION: SOLUTION ID:
114861
SOLUTION:
To disable the STAPLE and SORT feature in the OUTPUT mode, perform the following:
1. Access the 25 mode (power the copier ON with SW2 on the operation panel, while pressing the
2 and 5 keys).
2. Select option [1. SOFTWARE SWITCH].
3. Scroll to software dipswitch 20-4.
4. Press the ON button once. The top of the display should now indicate SOFTWARE SW20-4: 1
5. Power the copier OFF/ON to return to normal copy mode.
USAGE:
1
Intermittent F46-11 and faded copies while copying.DESCRIPTION: SOLUTION ID:
114963
SOLUTION:
CAUSE: The V-mirror assembly (Mirror mount plate/2 assembly) is bent and binding on the Lens
cover.
SOLUTION: Replace the V-mirror assembly (Mirror mount plate/2 assembly) (p/n 26NA-6191).
USAGE:
1
With Mixed Originals selected, unable to select Rotation group or Rotation sort (grayed out).DESCRIPTION: SOLUTION ID:
116418
SOLUTION:
CAUSE: Rotation group and Rotation sort are incompatible output modes with Mixed Original
mode.
SOLUTION: The following mode are incompatible with the Mixed Original mode:
1. Incompatible basic copying: Using platen glass (unless Platen store mode is used).
2. Incompatible Output modes: Rotation group and Rotation sort.
3. Incompatible Applications: Sheet/Cover insertion, Combination, Booklet, Transparency, Image
insert, Book copy, Special original (Folded original, Non-standard size, Upside down), Repeat, Fold
erasure, AUTO layout, Image shift, Non-image area erase and Stamp.
USAGE:
1
F35-6 occurs at power up.DESCRIPTION: SOLUTION ID:
116699
90
Copyright 2005, Konica Minolta Business Solutions U.S.A., Inc.
May 2005