Service manual

7020
8. Touch [EDIT] on the bottom of the touchscreen to change the setting to OFF.
9. Power the copier OFF/ON to exit the Key Operator Mode.
Can the watermark be reduced in printer mode?DESCRIPTION: SOLUTION ID:
91706
SOLUTION:
In printer mode the font can be changed thus reducing the size of the watermark
Note: The watermark cannot be reduced in copier mode.
USAGE:
1
Where is the serial number located on the 7020?DESCRIPTION: SOLUTION ID:
92220
SOLUTION:
The serial number is printed on a white bar-coded label located on the inside of the right-side door
on the right-hand side of the machine.
USAGE:
1
FK101, T09 and T76 errors, when sending confidential faxes through a PBX system.DESCRIPTION: SOLUTION ID:
92560
SOLUTION:
CAUSE: The V8/V34 protocol parameter is set to ON.
SOLUTION: To program the V8/V34 protocol to OFF, perform the following:
1. Power the copier ON.
2. Press the HELP key.
3. Touch [Key-ope mode] on the touchscreen.
4. Touch [2. FAX] on the touchscreen.
5. Touch [Special set] on the touchscreen.
6. Using the numeric keypad enter 9272 for password.
7. Touch [OK] on the touchscreen.
8. Touch [Function parameter setting] on the touchscreen.
9. Touch [Communication] on the touchscreen. [COMM parameter You can change setting] will be
displayed in the dark blue band at the top of the touchscreen and [V8/V34 protocol] will be
highlighted on the touchscreen.
10. Touch [EDIT] on the touchscreen until the set value displayed for V8/V34 protocol is [OFF].
11. Touch [BACK] three (3) times.
12. Touch [CANCEL] one (1) time.
13. Touch [BACK] one (1) time.
14. Touch [RETURN] one (1) time to return to the normal mode.
USAGE:
1
FK101, how to program two-sided fax reception mode.DESCRIPTION: SOLUTION ID:
93038
SOLUTION:
To enable two-sided receptions, perform the following:
1. Access the Key Operator Mode (press HELP, then touch Key Ope mode at the left front of touch
screen and then enter the Password if necessary).
2. Touch 2. FAX from the Key Operator Mode screen.
3. Select Tx/Rx mode set.
4. Select Reception output mode by pressing the down arrow on the right side of the touchscreen.
5. Edit the selection to display After all.
6. Press the down arrow in the lower left corner to display the next page.
7. Select 2sided reception and edit the selection to display ON.
8. Press BACK to return to normal operation mode.
USAGE:
1
Can the 7020 be programmed to print a TCR report using paper from a specific paper
drawer?
DESCRIPTION: SOLUTION ID:
93100
SOLUTION:
It is not possible to print a TCR report using paper from a specific paper drawer.
USAGE:
1
How to determine which IP unit is installed in the main body.DESCRIPTION: SOLUTION ID:
93969
SOLUTION:
To determine if the IP011 is installed, perform the following:
1. Press Scanner/Printer button
2. Press Setting button on the touchscreen.
3. Press 1 on the touchscreen for [Settings].
4. Press 5 on the touchscreen for [Test Print].
5. Press 1 on the touchscreen for [Demo/Configuration] Page.
6. Press Copy button to return to standby mode.
7. The configuration page will read IP011 System Configuration.
To determine, if the IP421 is installed, perform the following:
1. Press Scanner/Printer button
2. Press Setting button on the touchscreen
3. Press 1 on the touchscreen for [Test Print Menu].
4. Press OK on the touchscreen.
5. Press 3 on the touchscreen for [Config Data].
6. Press OK on the touchscreen.
USAGE:
1
84
Copyright 2005, Konica Minolta Business Solutions U.S.A., Inc.
May 2005