Service manual
7020
the proper firmware is installed based on the model main body. See information above.
VII. See [[7020/7025/7030/7035 Technical Bulletin #6| URL
http://techweb.konicabt.com/tpm/media/7020tb06.pdf]].
VIII. A 7035 equipped with a DF314 with an old style board flashed to firmware version below
20, currently level 16 or 17, will produce a copy that is stretched (enlarged) from lead-to-trail when
scanned through the DF314.
IX. A 7020, 7025 or 7030 equipped with a DF314 with an old style board flashed to firmware
version 20 will produce a copy that is compressed (reduced) from lead-to-trail when scanned
through the DF314.
X. See [[DF314 Revision of Rom Notice PDF file| URL
http://techweb.konicabt.com/tpm/media/df314-20.pdf]].
CAUTION: Flashing the DF314 CB with the incorrect firmware version may permanently damage
the DF314 CB.
*[[Trademark ownership information| FILE V:\TEXT\TRADEMRK.TXT NEW]]
Code 26-2 or 26-3 after upgrading firmware.DESCRIPTION: SOLUTION ID:
119731
SOLUTION:
CAUSE: Incorrect software dipswitch settings in the 25 mode.
SOLUTION: To verify 25 mode software dipswitch settings, perform the following:
1. Access the 25 mode (power the copier ON, while pressing the 2 and 5 keys).
2. Select [1. SOFTWARE SW].
3. Using the up/down arrows, scroll to software switches 24-0 and 24-1.
4. Select OFF.
5. Power the copier OFF/ON to exit the 25 mode.
USAGE:
37
How to program platen APS to select 8.5x11 with small size originals.DESCRIPTION: SOLUTION ID:
82241
SOLUTION:
To program platen APS to select 8.5x11 with small size originals, perform the following:
1. Access the 25 mode (hold down the 2 and 5 keys at power ON).
2. Select [1] (SOFTWARE SW).
3. Press the left down arrow 4 times.
4. Press the right up arrow 5 times. The top of display should indicate SOFTWARE SW 21-5:0
5. Press the ON button once. The top of display should now indicate SOFTWARE SW 21-5:1
6. Power OFF/ON to return to normal copy mode.
Note: This change to software switch 21-5, in the 25 mode, will allow platen APS to automatically
select 8.5x11 paper when copying a small size original (i.e., check, business card, drivers license
etc.).
USAGE:
36
How to print the system configuration page, 7020.DESCRIPTION: SOLUTION ID:
98249
SOLUTION:
Note: There are currently two print controllers (IP011 and IP421) available for the 7020.
Depending on which controller is installed, the procedure to print the System Configuration sheet is
slightly different.
To print a system configuration sheet, perform the following:
1. Power the copier ON.
2. Press the SCANNER/PRINTER key, located at the top of the operation panel.
3. Touch [SETTING] on the touchscreen.
4. If the display shows '1. Setting' at the top, complete the steps under the IP011 procedure. If the
display shows '1. Test Print Menu' at the top, complete the steps under the IP421 procedure.
IP011 procedure:
5. Touch [1] at the bottom of the touchscreen.
6. Touch [5] at the bottom of the touchscreen.
7. Touch [1] at the bottom of the touchscreen. The system configuration sheet will be output within
approximately 30 seconds.
8. Press the COPY key, located at the top of the operation panel, to return to the normal mode.
IP421 procedure:
5. Touch [OK].
6. Touch [3] and then [OK]. The system configuration sheet will be output within approximately 30
seconds.
7. Press the STOP key, to return to the normal mode.
USAGE:
36
FS107, F77-5 while copying and/or during finisher initialization intermittently.DESCRIPTION: SOLUTION ID:
114756
SOLUTION:
PROBABLE CAUSES:
1. A bind in either the paper pressure and/or the shutter plate drive systems, both are driven by
M707 (Paper pressure motor). Lubricate all the drive gears to the paper pressure and shutter plate
drive systems with Plas Guard*.
2. The metal bracket that supports M707 may be positioned on an angle causing a bind to the drive
USAGE:
36
8
Copyright 2005, Konica Minolta Business Solutions U.S.A., Inc.
May 2005