Service manual
7020
10. Select [12. Memory SW].
11. Press the arrows, in the lower left corner, and scroll to page 3/3 of the memory switches.
12. Press the down arrow on the right side and highlight Job Memory Recall.
13. Press EDIT to change the Job Memory Recall setting to ON.
14. Press RETURN three times to return back to normal copy mode.
15. Press the OUTPUT button located to the right of the touchscreen.
16. Select (highlight) the desired exit tray to be used as the default for copy jobs and press OK.
17. Press the APPLICATION button located to the right of the touchscreen.
18. From the APPLICATION screen, select JOB MEMORY located in the top right corner.
19. Press ENTRY located at the bottom of the job memory screen.
20. A CHECK MODE screen should now appear, verify that these setting are acceptable as copier
default and press OK. If settings are not acceptable, return back to normal copy mode and change
settings as desired and then continue programming starting at step 15.
21. From the job memory screen, press the down arrow and scroll to job memory #15.
22. Select (highlight) #15 and press OK.
23. Enter a name of your choice and press OK.
24. Press OK to return back to normal copy mode.
Note: To summarize, programming the 7020 in this manner forces the copier to automatically recall
job memory #15 when it initializes and auto-resets. All fax receptions will ignore job memory recall
and only react to what's programmed into Key Operator mode/ copier initial settings.
Severe developer spew on front and backside of all copies. The first half of the copy is
legible, but the last half is smeared with developer.
DESCRIPTION: SOLUTION ID:
153749
SOLUTION:
CAUSE: Loss of 24V DC on CN8-1 on the DC Power Supply (DCPS).
SOLUTION: Replace the DC Power Supply (p/n 26NA84510) as needed.
SPECIAL NOTE: Solution provided by Rick Johnson KMBS Windsor (KMPS)
USAGE:
2
J11-0 error message.DESCRIPTION: SOLUTION ID:
153758
SOLUTION:
CAUSE: Tray 1 feed roller hub has become damaged. The shaft is rotating, but the feed roller
does not turn.
SOLUTION: Replace the feed roller hub (p/n 26NA40100).
SPECIAL NOTE: Solution provided by Steve Carson, Southern Copier.
USAGE:
2
DF314, J63-0 occurs during copy mode.DESCRIPTION: SOLUTION ID:
155342
SOLUTION:
CAUSE: Restart timing is incorrect.
SOLUTION: To set RADF restart timing, perform the following:
1. Access the 36 mode (power the machine ON while holding down on the 3 and 6 keys).
2. Press the [2. Timing adj.] key.
3. Press the [2. Restart timing] key.
4. Press the [NEXT] key until the desired RADF adjustment item appears in the message display
area.
5. Press the [COPY] key.
6. Set the RADF adjustment chart on the RADF and select 11x17 size paper. Then press the Start
print button to make a copy. Adjust the "RADF double side (second side)", then make a test copy
in double side-single side mode and check the restart timing of 2nd output paper.
7. Check the restart (leading edge) timing of the output paper.
Standard value: Within ± 3.0 mm (life size).
8. Press the # button while pressing the * button to return to the restart timing adjustment screen.
9. If the restart timing is different from the standard value, enter a value from the numeric keys,
then press the [SET] key to store the adjustment value.
Input range -50 (slow) to +50 (fast).
1 step = 0.1mm.
10. Repeat steps 5 to 9 until the restart timing becomes a standard value.
11. Power the machine OFF/ON to exit the 36 mode.
USAGE:
2
Hecon* key counter availability.DESCRIPTION: SOLUTION ID:
156570
SOLUTION:
A kit (p/n SE95-4020) is available which includes all necessary mounting hardware and wiring. It
does not include the key counter (PCUA 950816). If individual parts are ordered referring to
[[Technical Operations Bulletin A4 D5| URL http://techweb.konicabt.com/tpm/media/A4D5.pdf]]
dated 6/25/03, the adapter wiring harness (p/n 1206K0010) is not needed since it is included with
the kit. Use the long adapter wiring harness. The short one is not needed. Directions are included
with the kit.
Note: To view the PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded
for free from the Adobe* Web site at: [[http://www.adobe.com/products/acrobat/readstep2.html|
USAGE:
2
79
Copyright 2005, Konica Minolta Business Solutions U.S.A., Inc.
May 2005