Service manual

7020
4. Select bit 1 of the switch using the middle up arrow.
5. Select ON (1) to enable the IP011.
6. Turn the copier OFF, then ON to exit the 25 mode.
FS107, intermittent J72-21 while copying.DESCRIPTION: SOLUTION ID:
132485
SOLUTION:
CAUSE: The paper exit connecting clutch has failed.
SOLUTION: Replace the paper exit connecting clutch (p/n 13GQ77181)
USAGE:
2
Intermittent cycling of power, during copy operation or at power up.DESCRIPTION: SOLUTION ID:
137776
SOLUTION:
CAUSE: The DCPS fan (FM1) failed.
SOLUTION: To check the DCPS fan (FM1), perform the following.
1. Access the 47 multimode (power the machine ON while holding down on the 4 and 7 keys) input
code 42, press P-4-P.
2. Press the print button and see if the DCPS fan (FM1) comes ON.
3. If the DCPS fan (FM1) (p/n 26NA80510) does not come ON, replace it.
4. Power the machine OFF/ON to exit the 47 multimode.
USAGE:
2
The machine powers OFF during copy mode.DESCRIPTION: SOLUTION ID:
137781
SOLUTION:
CAUSE: The DCPS fan (FM1) failed.
SOLUTION: To check the DCPS fan (FM1), perform the following.
1. Access the 47 multimode (power the machine ON while holding down on the 4 and 7 keys) input
code 42, press P-4-P.
2. Press the print button and see if the DCPS fan (FM1) comes ON.
3. If the DCPS fan (FM1) (p/n 26NA80510) does not come ON, replace it.
4. Power the machine OFF/ON to exit the 47 mode.
USAGE:
2
Page numbering is missing for the odd pages of the second set.DESCRIPTION: SOLUTION ID:
138591
SOLUTION:
CAUSE: Firmware bug with level 33 Control firmware.
SOLUTION: Install level 33cia Control firmware.
USAGE:
2
F35-6 at power up.DESCRIPTION: SOLUTION ID:
140456
SOLUTION:
CAUSE: The fuse mounting plate assembly has failed.
SOLUTION: Replace the fuse mounting plate assembly (p/n SP00-0110).
SPECIAL NOTE: Solution provided by Paul Butler, Copy Products, Inc.
USAGE:
2
The hard counter does not work.DESCRIPTION: SOLUTION ID:
148875
SOLUTION:
CAUSE: The SCDB failed.
SOLUTION: To check the SCDB, perform the following:
1. Access the 47 mode (power the machine ON while holding down the 4 and 7 keys), output code
43.
2. Press the print button and watch for a change at the total counter.
3. If there is no change of state, using a volt meter check for 24V DC at CN66-6 on the SCDB.
4. If there is no 24V DC at CN66-6, replace the SCDB (p/n 26WA-9050).
USAGE:
2
IT101, how to program a specific finisher exit tray for fax receptions and another finisher
exit tray for copy jobs.
DESCRIPTION: SOLUTION ID:
151224
SOLUTION:
To program the 7020 to have fax receptions exit into one finisher tray and copy jobs into a different
finisher tray, perform the following:
1. From the copier mode, press the HELP (?) button, located to the right of the touchscreen.
2. From the touchscreen, select Key-Ope mode.
3. Enter a Key Operator passcode if applicable.
4. Select [1. System/Copier].
5. Select [2. Copier Initial].
6. Select [5. Output].
7. Select (highlight) the desired exit tray to be used for fax receptions press OK.
8. Press RETURN to return back to the System/Copier setting menu.
9. Press the down arrow to scroll to the next System/Copier setting menu screen.
USAGE:
2
78
Copyright 2005, Konica Minolta Business Solutions U.S.A., Inc.
May 2005