Service manual

7020
2. From the touchscreen, select Key-Ope mode.
3. Enter a Key Operator passcode if applicable.
4. Select [1. System/Copier].
5. Select [2. Copier Initial].
6. Select [5. Output].
7. Select (highlight) the desired exit tray to be used for fax receptions press OK.
8. Press RETURN to return back to the System/Copier setting menu.
9. Press the down arrow to scroll to the next System/Copier setting menu screen.
10. Select [12. Memory SW].
11. Press the arrows, in the lower left corner, and scroll to page 3/3 of the memory switches.
12. Press the down arrow on the right side and highlight Job Memory Recall.
13. Press EDIT to change the Job Memory Recall setting to ON.
14. Press RETURN three times to return back to normal copy mode.
15. Press the OUTPUT button located to the right of the touchscreen.
16. Select (highlight) the desired exit tray to be used as the default for copy jobs and press OK.
17. Press the APPLICATION button located to the right of the touchscreen.
18. From the APPLICATION screen, select JOB MEMORY located in the top right corner.
19. Press ENTRY located at the bottom of the job memory screen.
20. A CHECK MODE screen should now appear, verify that these setting are acceptable as copier
default and press OK. If settings are not acceptable, return back to normal copy mode and change
settings as desired and then continue programming starting at step 15.
21. From the job memory screen, press the down arrow and scroll to job memory #15.
22. Select (highlight) #15 and press OK.
23. Enter a name of your choice and press OK.
24. Press OK to return back to normal copy mode.
Note: To summarize, programming the 7020 in this manner forces the copier to automatically recall
job memory #15 when it initializes and auto-resets. All fax receptions will ignore job memory recall
and only react to what's programmed into Key Operator mode/ copier initial settings.
How to flash the 7020 firmware with the ISW Trns utility.DESCRIPTION: SOLUTION ID:
83265
SOLUTION:
To flash the firmware, perform the following:
SETTING UP THE ISW UTILITY
1. [[Obtain the ISW Trns utility file from the Konica web site| URL
http://techweb.konicabt.com/tpm/media/iswhowtoget.txt]].
Note: While on this page, download the [[DF314 and FS107 files| IMAGE v:\bitmaps\ISW018.bmp
SCROLL]], by clicking on the appropriate link and following instructions.
2. While still at Konica's web site, download the 7020 firmware. To download the firmware
programs, perform the following:
a. Click on the back arrow to return to the previous page.
b. Click on [Eproms for Low Volume Copiers].
c. Click on [List] button.
d. To start the download, click on the [[control or image firmware program| IMAGE
v:\bitmaps\ISW015.bmp SCROLL]] link and follow the instructions.
3. [[Install the ISW application program onto a PC or laptop| IMAGE v:\bitmaps\ISW005.bmp
SCROLL]].
4. [[Set up the ISW Trns utility| IMAGE v:\bitmaps\ISW004.bmp SCROLL]] by following the setup
directions.
5. [[Set up the folders| IMAGE v:\bitmaps\ISW008.bmp SCROLL]] for the BIN files.
6. When the [[ISW Trns utility main window| IMAGE v:\bitmaps\ISW009.bmp SCROLL]] pops up,
the BIN file data can be selected, verified, and sent to the machine for flashing the firmware.
Notes:
a. There are two types of [[data sources| IMAGE v:\bitmaps\ISW010.bmp SCROLL]] -
ORIGINAL (batch data) and DIVIDED (divided data). The 7020 utilizes the DIVIDED selection for
the Control BIN files and the ORIGINAL selection for the Image, DF314 and FS107 BIN files.
b. The Country selection must be KBT for the USA.
COPYING TRANSFER DATA (UPDATE DATA)
Run the ISW Trns program to [[copy transfer data| IMAGE v:\bitmaps\ISW012.bmp SCROLL]]
(update data) to the PC.
CONNECTING
[[Connect a parallel interface cable to the copier.| IMAGE v:\bitmaps\cjc292.bmp SCROLL]]
ISW connector is located on the right rear side of mainbody and is the lower of the 2 connectors.
CAUTION: If a parallel data transfer is to be executed with the ISW Trns program, the ECP mode
setting of the PC parallel port should be cleared. ISW Trns does not support parallel data
transfers. If a parallel data transfer is launched with the PC set in ECP mode, the transfer could be
aborted by an error occurring in between. It would be necessary, therefore, to [[disable ECP mode|
IMAGE v:\bitmaps\ISW011.bmp SCROLL]] before run ISW Trns on a PC with the ECP setting.
UPDATING
[[Update the ROM data on each control board using ISW Trns.| IMAGE v:\bitmaps\ISW014.bmp
USAGE:
48
5
Copyright 2005, Konica Minolta Business Solutions U.S.A., Inc.
May 2005