Service manual

7020
10. Touch RETURN to restore the BASIC SCREEN to perform copying operations.
How to scan two small originals from the platen glass and have both images on one side of
a copy.
DESCRIPTION: SOLUTION ID:
100202
SOLUTION:
To program the copier to scan two small originals from the platen glass and have both images on
one side of a copy, perform the following:
1. Press the APPLICATION key.
2. Select STORE MODE.
3. Select COMBINATION.
4. Select 2-in-1.
5. Select OK twice.
6. Center the first side of the original with the scale plate and press SCAN.
7. Flip the original over and center the second side of the original with the scale plate and press
SCAN.
8. Press the START key.
USAGE:
4
FK101, NO PAPER is displayed in Fax mode and the machine will not print received faxes.
Paper is loaded in all trays.
DESCRIPTION: SOLUTION ID:
104264
SOLUTION:
CAUSE: Incompatible programming between Copier/System Key Operator Mode and Fax Key
Operator Mode. The ATS/APS settings for each paper tray, in Copier Key Operator mode Memory
switches, are set to OFF and the RX feed tray (fix) setting in the Fax Key Operator mode TX/RX
mode set is set to AUTOMATIC.
SOLUTION: To resolve this problem, either the ATS/APS setting for at least one paper tray, must
be set to ON, or the RX feed tray (fix) setting must be set to a fixed paper tray.
To program ATS/APS for each paper tray, perform the following:
1. From the normal Copier mode, press the HELP (?) button located to the right of the touch
screen.
2. Press KEY-OPE MODE located in lower left corner of the touch screen.
3. Press [1] System/Copier.
4. Press the DOWN arrow located on the lower left corner of the touch screen to access the
second page of Key Operator Mode selections.
5. Press [12] Memory SW.
6. Press the DOWN arrow located in the lower left corner to scroll to page 2 of the Memory SW.
7. Use the UP and DOWN arrows located on the right side to scroll to the ATS/APS settings for
each paper tray.
8. Press EDIT to enable (ON) ATS/APS for the tray or trays desired.
9. Press Return three times to return back to the normal Copier mode.
To program RX feed tray (fix) setting in the Fax Key Operator mode to a specific paper tray,
perform the following:
1. From the normal Copier mode, press the HELP (?) button located to the right of the touch
screen.
2. Press KEY-OPE MODE located in lower left corner of the touch screen.
3. Press [2] FAX
4. Press TX/RX mode set.
5. Press the UP or DOWN arrow located on the lower left corner to scroll to page 2 of the TX/RX
mode set.
6. Use the UP and DOWN arrows located on the right side to scroll to RX feed tray (fix).
7. Press EDIT to change this setting to a desired specific fixed tray.
8. Press BACK twice, and then RETURN once to return to the normal Copier mode.
USAGE:
4
DF314, blur caused by the original skewing over the slit glass.DESCRIPTION: SOLUTION ID:
104755
SOLUTION:
CAUSE: Incorrect tension between the reading roller and the slit glass.
SOLUTION: Adjust the RADF height adjustment screw located through the hole in the top of the
rear RADF cover (p/n 13GL12020) to set the height adjustment indicator (p/n 13GL45550) at the
center of the scale. To view the RADF height adjustment indicator, open the top cover of the RADF
and look to the left of the rear jam release lever (p/n 13GL45730).
USAGE:
4
FS107, addition of tension pulley and rocking gear/D mounting plates.DESCRIPTION: SOLUTION ID:
109204
SOLUTION:
The part number for the tension pulley (13GQ48300) mounting plate (front and rear) is 13GQ-1540.
The part number for the front rocking gear/D (13GQ77130) mounting plate is 13GQ-1520. A part
number for the rear rocking gear/D mounting plate is not available. If this plate is required, contact
parts order entry (1-800-284-5555) and request a parts escalation.
USAGE:
4
47
Copyright 2005, Konica Minolta Business Solutions U.S.A., Inc.
May 2005