Service manual

7020
SOLUTION:
CAUSE: If faxing from the RADF, no image will show on the TCR report because the machine
does not use the memory to send. The image being reduced is the operation of the machine.
SOLUTION: This is normal operation when using quick transmission faxing through the RADF. If
image on the TCR is required then set the machine for memory transmission. To set the machine
to memory transmission, perform the following:
1. Press ? (HELP) button.
2. Press Key-Ope button on the touchscreen.
3. Enter key operator passcode, if required.
4. Press FAX button on the touchscreen .
5. Press Tx/Rx mode set on the touchscreen.
6. Press Edit to select Memory Tx.
7. Press Back button twice.
8. Press Return.
USAGE:
66
DF314, after performing paper size detection adjustment, the original size is still not
detected correctly.
DESCRIPTION: SOLUTION ID:
103077
SOLUTION:
CAUSE: Incorrect resistance of VR301 (size detect VR).
SOLUTION: To verify the output of VR301 (size detect VR), perform the following:
1. Access 47 mode (turn the copier ON, while pressing the 4 and 7 keys) input code 60, press star
(*) 09(*),
2. Place 8.5x11 original in the document tray.
3. LCD display should show a value of 217.
4. If unable to show a value of 217, go to the next step. If 217 is displayed in the LCD screen, go
to to step 11.
5. Remove the 5 screws located on the bottom of the document tray.
6. Remove the white gear on VR301 (size detect VR).
7. Place 8.5x11 original in the document tray.
8. Rotate the black knob on VR301, until a value of 217 is displayed on the LCD screen.
9. Power machine OFF/ON.
10. Perform the original size detection adjustment.
11. Place an original in the document tray. If the size is still incorrect, perform the paper size
detection adjustment as follows:
12. Access the 47 mode (turn the copier ON, while pressing the 4 and 7 keys) output code 69.
13. Place 5.5x8.5R original in the document tray.
14. Press Start button.
15. Press the Stop/Clear button.
16. Press Star (*) button.
17. Press 1 to display <069-001>, and press (*) again.
18. Place 8.5x11 original in the document tray.
19. Press Start button.
20. Press Stop/Clear button.
21. Power machine OFF/ON.
USAGE:
58
DF314, how to perform original size detection adjustment.DESCRIPTION: SOLUTION ID:
89134
SOLUTION:
To perform the original size detection adjustment, perform the following:
1. Access the 47 mode (power the copier ON with SW2 - operation panel switch, while pressing
the 4 and 7 keys).
2. Enter 6, 9 (display should read <069-000>).
3. Place 5.5x8.5R original in the document tray.
4. Press Start button.
5. Press the Stop/Clear button.
6. Press Star (*) key.
7. Press 1* to display <69-001>.
8. Place 8.5x11 original in the document tray.
9. Press Start button.
10. Press Stop/Clear button.
11. Power machine OFF/ON with SW2.
Note: The 7020/7025/7030/7035 service manual (3/2001) page 4-79 is incorrect regarding this
adjustment.
Step 3 minimum width position is 5.5x8.5R and Step 7 maximum width position is 8.5x11.
USAGE:
56
FK101, how to program a specific finisher exit tray for fax receptions and another finisher
exit tray for copy jobs.
DESCRIPTION: SOLUTION ID:
93954
SOLUTION:
To program the 7020 to have fax receptions exit into one finisher tray and copy jobs into a different
finisher tray, perform the following:
1. From the copier mode, press the HELP (?) button, located to the right of the touchscreen.
USAGE:
53
4
Copyright 2005, Konica Minolta Business Solutions U.S.A., Inc.
May 2005